Having problems with your Bosch Dishwashers ?

Replacing a fuse in dishwasher

\015 Water left in dishwasher after cycle, no power to panel\015

Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher 66513752K601 keeps blowing the thermal fuse. (Bi-Metal W10258275). I have replace the Thermal fuse several times. After i replace the fuse for some reason after a few months or less it will blow it out again. I have also replace the front panel assembly after it stopped working correctly. I would like to know how to test the dishwasher to find out the root cause of the fuse issue. I don't want to be replacing the fuse every time and don't have the $$ to buy a new dishwasher. Everythin


... Dishwashers

IDL750 - Fuse trips when turned on. HELP! We had some electricians here to install a new electrical socket for a new fridge. They put the new socket in the same wiring as for my existing dishwasher!! The first time I tried to start the dishwasher cycle with the new fridge plugged in, the circuit box fuse tripped. Now, even with the fridge turned off, the dishwasher makes the fuse trip when turned on. Is there a fuse inside the dishwasher that has blown and needs to be replaced? or a ground brea


Hi.The first step is understanding if the problem is the socket or the appliance. Find an extension long enough to reach a different socket. Move the appliance to reach the power cord, and connect the dishwasher to a different power sock ... Indesit 24 in. IDL700 Built-In Dishwasher

I have a kitchen aid dishwasher model number KUD101TJBLO. I have had the thermal fuse replaced numerous times. It may run two weeks ir it may rub two cycles then the fuse blows. My serviceman has given up on finding a solution.He has replaced the control board and the door switch. However it continues blowing the fuse. I read on the internet that you need to replace the entire wiring kit that comes with the fuse but my repairman says this will not fix the problem and refused to replace the kit.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please check for the short on the wires near the heating element. Also check the resistance of the heating element, it should not be more than 1.6 K ohms. Also ma ... KitchenAid Dishwashers

We replaced thermal fuse (inc all wires), worked for about 2 months. Replaced thermal fuse again, ran it 2x's, 2nd X it broke. We have a new thermal fuse on hand, but need some advice on what could be causing the problems. When the dishwasher does work, it cleans as if new.


Probably a bad heating element, You may want to change that to before replacing the fuse again. ... Dishwashers

Hi I have the Kitchenaid dishwasher KUDIO1FLSS2 and all the buttons work except the two most important ones, the heavy and normal cycle. I had a service person out about 6 mo. ago and he said the control panel was about to go bad and replaced a fuse. He ended up coming again a week later and replacing the fuse with a stronger fuse. Now it's acting up again and I'm sick of hand washing dishes and don't feel like handing over another $300 or more if I can do it myself or maybe I just need to buy a


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Whirlpool dishwasher model DU1055XTSQ2 will not run. Only half of lights on control panel working. Probably need to replace control panel. Do I need to replace the bi-metal fuse also. What does the bi-metal fuse do, how would I know if bi-metal is bad, what are symptoms.


... Whirlpool Dishwashers

Thermal fuse Dishwasher konked out mid-cycle and now no power to control pad. We've already had the thermal fuse replaced once (machine is only 2 years old!) and this appears to be the same issue. I tried to open the front and I think I can see where it is but not sure how to get it out and replace it AGAIN. I wasn't able to get the inside panel completely apart from the front of the unit so I was somewhat limited. I'd rather save the service charge if I can and there's n


Http://www.partselect.com/MultiModels.aspx?ModelNum=KUDS35FXSS&SearchTerm=fuse&RefineSearch=0Maybe this link will help ... KitchenAid KUDS35FXSS Dishwasher

My dishwasher has no power. A service tech came a few months ago and replaced the mother board along with a fuse. Am I having a short and need to replace the fuse? If so,where and how would I do that?


... KitchenAid KUDM01TJBS Dishwasher

I have a Whirlpool DU1055XTSS dishwasher that completely stopped working. I took it apart, found the thermal fuse to be bad, ordered a new, then replaced it and it worked for 2 loads. Now the thermal is open again. What could be "taking it out"? Is the thermal fuse strictly a thermal or does it repsond to current? It's 2 years old, i have already replaced the heating element, the main control board, and now the thermal....twice.


Hi.If the thermal fuse is blowing, that means that there is overheating.Common causes for overheating are:Thermostat cutting off too late.Plugged element.Plugged element means that the element sta ... Whirlpool Dishwashers

Bimetal fuse The incoming power was blinking off and on due to a storm, it caused the bi metal fuse to fail in the dishwasher when it was not operating, the fuse was replaced with kit #w10258275, now two weeks later the fuse has failed again while operating.These fuses are expensive, I would like to know the value (amps) of these fuses so that the system can checked to try and find out the reason for failure, or maybe you might have an idea where to start. Thanks Tad


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

My Whirlpool GU2400XTP dishwasher keeps blowing the fuse. It sat up for 6months because the control panel went out and I couldn't afford to get a new one. Finally replaced the panel and the thermal fuse blew during the first wash cycle. I tried to put a 15AMP fuse in it's place to check it out before I bought a new thermal fuse and it too blew during the first cycle. Any ideas?


Are you replacing the wires along with the fuse? It is important to change the wires too as they are usually the cause for the fuse blowing. Be sure and get the fuse kit that includes the wires. \015\012\015\012Is your water too hot? Hot ... Whirlpool GU2400XTP Built-in Dishwasher

We have a 6 year old Jenn Air dishwasher model JDB2150AWP We had a cracked door close unit which we replaced but got a short while restoring connections I am wondering if there is an internal circuit breaker, relay or fuse on these machines that we need to check and possibly replace since we cannot get it to run at all. No power or lights at all. I believe all connections are secure and we replaced the door close unit with new parts.


... Jenn-Air 24 in. JDB2150AWP Built-in Dishwasher

When on/off button de-selected large flash from top of door. Main consumer unit tripped and fuse in plug found ruptured. Fuse replaced cb reset but dishwasher has no power. Fuse rechecked found to be good.


Dishwasher stripped down and found MAIN WIRING HARNESS chaffed agains door during opening and closing. New loom in region of £100 so repared old loom. ... Dishwashers

Does GU3200XTS Dishwasher have a reset. Our dishwasher stopped about 45 mins left in cycle, we have replaced fuse but dishwasher does not work.


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

KitchenAid dishwasher: KUDS01FL - I have had to replace the fuse every year and now I can't even get through on cycle with the fuse going. It is now dead again! It almost makes it through the full cycle and then stops (fuse blows)- no power - and there is some water left in the bottom which I have to physically remove. I spent a fortune on repairs every year since I bought it and would like to try to avoid another charge. I appreciate any help that you can offer. Thank you, Carol


I would check the pump. It may be slightly jammed or have debris which is causing it not to fully move or cause it to move very hard popping the breaker. Also with a jammed or broken pump, that can also cause water to be left in the bottom of the mac ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My Beko D3422 FS was washing normally and the residual current device tripped approximately half way through the cycle. I have unplugged the dishwasher and checked the plug socket with various other appliances. None have tripped the RCD. I have stripped the Dishwasher to look for any disconnected terminals or shorted wires and cannot find anything obviously burnt or any signs of shorting. The 13amp fuse in the dishwasher plug is fine. Are there any components I can test or replace which wouldgi


... Dishwashers

I have a fisher & Pakel dishwasher and it appears to have brown a fuse inside the machine which means it does not work at all and the problem occurred during the wash cycle. This means the seal (which is a top piece that's lifted and lowered by two motors. When the seal is in the lowered position it creates a complete seal but it also locks the drawer (single drawer dishwasher) so it cannot be pulled out. I repaired the dishwasher two years ago. One of the lifter motors didn't work. I replaced t


According to the service manual there is no problem in manually forcing open the drawer in the situation where the power has failed part way through the diswasher cycle.\015\012\015\012The problem is that once you force the lid open, you ... Fisher and Paykel Dishwashers

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

Kitchenaid Dishwasher (KUDM01TJ) replaced thermal fuse, blew out again after two loads, could there be a larger problem?


... Dishwashers

Kenmore 665.1646 dishwasher. A nearby lighting strike killed some electronic devices in our house. We have electricty to our dishwasher but the console will not light at all. The fuse, latch switch and overfill switch all check out good. We replaced the electronic control, 8539379, and still have no lights. What else could it be?


Hi.If you have tested fuse, overfill, latch, and you have a new electronic control, then it is necessarily a wiring problem. However, since wiring problem causing this after lighting is quite uncommon, I suggest double checking all the re ... Dishwashers

Whirlpool Dishwasher No Power: GU1200XT dishwasher thermal fuse in power up circuit blew & was replaced about two months ago. It has blown again. Both times it was after wash was finished but water was left in tub. Would appreciate suggestions on what may be causing the hi temp condition and how to verify.


I have a similar problem with my whirpool diswashre GU2500XTPB1. I check thermal fuse (on the board. It is OK (continuty). Right door switch _ OK, Left door switch _ weaker a bit). It still not work) I do not know what to check? ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

My whirlpool dishwasher Model No. ADG 450-3 is not heating the water. Can you let me know where the element is or is there a fuse i could replace. Where would I get a diagram of the inside workings of this dishwasher?


... Dishwashers

I have a Whirlpool DU1055XTSS dishwasher that completely stopped working. I took it apart, found the thermal fuse to be bad, ordered a new, then replaced it and it worked for 2 loads. Now the thermal is open again. What could be "taking it out"? Is the thermal fuse strictly a thermal or does it repsond to current? thanks


Water is getting on the wiring somewhere, take it apart right after a cycle and see if you have a door leak, or the motor is going bad ... Whirlpool DU1055XTS Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1154 seconds