Having problems with your Bosch Dishwashers ?

My Bosch SHY66 does not heat the water. How can I differentially diagnose the heater being the problem from the problem being a failure of the thermal switch?

\015 Bosch SHY66 no longer heats the water; what's an efficient diagnosis?\015

Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch SHY66 does not heat the water. How can I differentially diagnose the heater being the problem from the problem being a failure of the thermal switch?


... Bosch Dishwashers

Hi I have a Zanussi ZDF501 dishwasher that stopped heating up intermittently. It got worse and I fitted a new heater and all was ok for a few months. Then the intermittent failure started again. Note that I tested the old heater and it is actually OK without a short circuit so I don't think it was the problem adn can be re-used. Could it be the thermostat or heat sensor? I am concerned it might be the PCB since the failure was intermittent. Thanks Dave


In my case, although the solder joints on the relay looked poor, improving them didn't help. I had to replace the relay. Fortunately, Maplin stock a compatible one, JM67X for 1.99. See ... Zanussi Dishwashers

I have Whirlpool control board part #8267371. The problem is that the dishwasher does not complete a cycle. A green light on the door will flash. From what I understand it indicates a failure in the heater at some point. I replaced the heater and all I am left with now is the possibility that the control board has failed. So my question is this. Are there common problems associated with these boards ? Which components should I be looking at ? I don't have a schematic. Or is there anyone that can


Yeah, I'm in the middle of that, too. There's a thermal fuse you can check with a meter just above the control panel inside the front door. It should be 0 ohms. Then it's the control board, I guess. Looking for the same one myself right now. I'm goin ... Kenmore 24 in. 16032 Built-in Dishwasher

I have a JennAire jdb1090aws dishwasher. It's about 4 years old. The symptom is no water flowing through dishwasher. Approx 3 months after installation, the same symptom occurred. Tech resolved with float switch adjustment (no charge). Has run fine every since. I have not checked water supply, but doubt this is the problem (new water heater 3 months ago, sediment gone). I suspect the float switch is bad or out of adjustment. How do I trouble shoot float switch in dishwasher? Connect ohm mete


Hi,The procedure to test the float switch :-http://www.partselect.com/dishwasher+test-float-switch+repair.htmMost for no water entering the dishwasher, there are 2 main causes. One is the float switch and the other ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

Email [email protected] i have a cma c dishewasher It was going through a cycle and it just stopped. there is power to the switch (Cycle starter switch on front.)also the heater also is now not working What could be the problem the relay switch??


... Cma Dishmachines CMA-66L Dishwasher

HE error My LG LD-14aw1 is showing HE error code - Heater Circuit is troubled???. (Not as much as owner!!!). I have repaired several dry solder joints in the control module, which have been causing various operating failures, but the HE problem has got me stumped. Can anyone provide me with a wiring diagram of the machine and or the control module? I'd like to trace the heater circuit to see if I can find the fault. Many thanks


From the manual: Errors: HE: Heater circuit failure.Please call your Authorized Service Center or LGECustomer Service at 1-800-243-0000(US), 1-888-542-2623(Canada). ... LG 24 in. LD-12BW5 Free-standing Dishwasher

We have about 5 bauknecht oven and we have a problem with the heater element adn selector switch,where we can buy the spare parts in singapore


... Bauknecht 24 in. GSF8971 Built-in Dishwasher

Hi In the middle of a wash cycle, my dishwasher tripped the circuit breaker on the wall. I diagnosed this by unpluggin dishwasher, plugging in a different appliance and switching circuit breaker back on. new appliance worked OK. When dishwasher had cooled, I tried it again on same circuit (which I knew was working properly). The lights came on for about three seconds, and then the circuit breaker cut back in again, so I knew it was the dishwasher that was causing the problem. Is there anyt


Ck the connections where the cord hooks to the wiring harness. look for hot or shorted wiring . also ck the contro panel for the same . generaly if you have a power draw like you are saying then you can see t ... Dishwashers

Kitchenaid kuddo1dppa I own a KitchenAid KUDD01DPPA, 2 drawer dishwasher. I am not a technician, however I have had a lot of experience in repairing various appliances and am savvy with electronics and mechanical technical issues. Here's the problem: I was getting rinse error codes in both drawers, pulled the bottom drawer out, removed the cover to the circuit board and used a dryer to dry up the moisture on the flood switch. Now I am getting Fill Failure error code on both drawers. I have g


Test this steps and fix it. God bless you\012 \012 Water Inlet Valve\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

I purchased an 18 inch frigidaire dishwasher in February of 2006 - model fdr252rbs serial # th 54593325 my instruction catalogue states that there is a 2 year warranty on the motot. Unfortunately the appliance repairman diagnosed the problem as the motor burn out or failure. I cannot believe that a motor should die after only 2 & 1/2 years I have purchsed many frigidaire appliances over the years and had great respect for their quality which has evevidently been lost For that reason I sha


WHEN I CALLED ELECTROLUX I WAS PUT ON HOLD FOR 45 MINUTES AND \015\012WAS NOT ABLE TO COMMUNICATE MY PROBLEM TO ANY ONE.AND WAS \015\012FORCED TO LISTEN TO ' we appreciate your patience' please hold' over and over\015\012 during tha ... Electrolux Dishwashers

Hobart lx30H Fuse f1 3.2amp 250vac blown, f1 feeds relay board. No booster temp, pump and sump heater active (OK). Can problem be from other devices that are driven from the low power relays on this board or are we looking at a board failure as the only answer. No skinny on door panel, Can't get access to OEM repair manuals anywhere on line Thanks


Possible bad relay coil ... Hobart 24 in. LXIH-3 Built-in Dishwasher

I have an 8 year-old Kenmore 665.16912 dishwasher. Worked fine until two days ago. Then it stopped working altogether: nothing lights up on the front panel. I have checked the 120 in the electrical box, the door switch is working, the thermal fuse is working and there is 120 volts at the white and black connections to the timer control board. I bought a new timer control board for $120 and that did not fix the problem. What else could be causing the unit to completely stop working?


If all are really good then the only thing it con be is the display (8269205) $25.00 part, if it's bad dishwasher wont run ... Kenmore 16912 Built-in Dishwasher

I have a kitchen aid dishwasher model number KUD101TJBLO. I have had the thermal fuse replaced numerous times. It may run two weeks ir it may rub two cycles then the fuse blows. My serviceman has given up on finding a solution.He has replaced the control board and the door switch. However it continues blowing the fuse. I read on the internet that you need to replace the entire wiring kit that comes with the fuse but my repairman says this will not fix the problem and refused to replace the kit.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please check for the short on the wires near the heating element. Also check the resistance of the heating element, it should not be more than 1.6 K ohms. Also ma ... KitchenAid Dishwashers

No power. how can i tell if my problem is door switch, thermal fuse or circut board?


... Whirlpool 24 in. DU915QW Built-in Dishwasher

I have a kenmore 665.13593k600 dishwasher replaced both door switches and the thermal fuse once now the fuse blew again what might be the problem


... Kenmore Dishwashers

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

High limit light goes on and unit shuts off about 20 seconds into start of cycle. Disconnected both wash and rinse heater elements problem continues Disconnected white wire at high limit thermostat problem continues disconect white with blue tracer problem continues whacked thermostat with pliers no luck whacked rinse heater thermo with plers no luck relay for rinse heater clacks and unit shuts down


Well, while I must admit that "Percussive" maintenance, sometimes works, as you have discovered there is more to servicing than, just "Giving it a good whack" lol.\015\012\015\012The problems with these units, is usually to do with the Thermost ... Jackson 25 in. TempStar HH Free-standing Dishwasher

Fisher paykel dd 603 top drawer no power heater plate thermal fuse ok


... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

WHAT ARE THE THERMAL FUSE SPECIFICATIONS FOR KENMORE ELITE MODEL 66513122K701SERIAL NUMBER FY1211868 AND WHAT IS THE PART NUMBER FOR A THERMAL FUSE KIT? WE HAVE HAD TWO FUSES BLOW AND THERE DAMAGE TO THE WIRING ON THE LEFT HAND SIDE OF THE CONTROL PANEL THAT CONNECTS O THE SWITCH. THEIR IS DISCOLORATION ON THE PARTS AND WIRING. WE HAVE SEEN EXPERTS STATE THAT IN ORDER TO CORRECT OUR ISSUE WITH THE FUSE BURNING OUT WE NEED A THERMAL FUSE KIT AND WE NEED THE SWITCH AND THE WIRING THAT CONNECTS TO


Http://appliancejunk.com/ge/dishwasher/31-9137.pdf\015\012\015\012A ... Dishwashers

I have a AM14 (ML32614) Hobart dishmachine, my tech is having problems with the new style door switch (ordered 918320-00001) which is the round black barrell style. the old switch was a flat type switch. He is having problems mounting, please help.


... Hobart AM14-253 Free-standing Dishwasher

My asko dishwasher(1504) keeps running sometimes, The time will run down to 1 min on the disply and stay there and run on and on until I turn it off. Prior to this another problem occured, when the washer does shut off on it's own, the display will read F1(Falt in the heater), I am wondering if one problem has to do with another. The heater problem I can deal with but not the continueous running.


F1 doesn't mean that it's always the heating element itself, often it \015\012can be the control board relay that has shorted and isn't sending power \015\012to the element. If the element is the faulty part, you'd be looking at \015\012about $250 f ... Dishwashers

Model Karcher 320H 1.141-205 When first switched on the pressure builds up and then the machine keeps no switching on and off, opening the trigger on the lance and it works ok, close trigger and the pulsing starts again, if left like this it would probably burn the motor out. I have lubricated the brass/plastic piston the operates the on/off switch but problem still exists. I have also opened the pump chamber but cannot see any debris or problems with the rubber seals. Any help would be most app


... Karcher 1550PSI Pressure Washer

I have a karcher 650m, when assemlbed the off on switch wont work, when dismantled the switch seems to work, tried greasing the switch, anybody know how to fix this problem??


... Pressure Washers

My dishlex dishwasher is a model 560 silent range with eco save and has a printed circuit type switch arrangement it has man code of b8833ww or 88833ww the problem is that the pause start button activates but dose not latch in I suspect that the problem is with a latching relay behind the switch panel as i have had the front off and cleaned the contcts with contact cleaner! all of the buttons work including pause ! any advise would help as would a wiring diagram and or a operation or wor


Latching relay or door lock assembly need for you to check on that model number 560 silent range wont come out on dishlex's site should be a dx followed by some numbers try also to shut off the main power for 7 minutes to the unit to reset the contro ... Dishwashers

My Hotpoit FDL570g dishwasher (that is less than 2 years old) is tripping the circuit breaker originally during a wash and now when the unit is switched off and and door is closed. I thought it may be a door lock / microswitch problem and replaced the microswitch. The dishwasher was good for four seperate washes but now the problem has come back when crockery is loaded when the machine is switched off. I'm going to check for bare / rubbed leads but not expecting to find this with a dishwasher of


Hi,\015\012\015\012If your washer is tripping the breaker when it is switched off, this is often a sign that water has leaked - or is leaking - into the bottom of the washer under the washing compartment where there are lots of exposed el ... Hotpoint 24 in. FDW60 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0694 seconds