Having problems with your Bosch Dishwashers ?

Replaced the control board in Bosch Dish Washer SHE44C and the cycle times are reversed???

\015 The pot scrubber cycle is shorter than the reg. cycle.\015

Answers :

I think this board requires coding to your particular model?? your dishwasher has four selection button and a delay start, whereas the module has five selections and delay as it is used in several different modesl. The coding info should have been in the box with the part and may need to be carried out directly on the module with the fascia panel removed. If you post the part number of the module I will see if I can get you the coding information..
Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replaced the control board in Bosch Dish Washer SHE44C and the cycle times are reversed???


I think this board requires coding to your particular model?? your dishwasher has four selection button and a delay start, whereas the module has five selections and delay as it is used in several different modesl. The coding info should have been i ... Bosch Dishwashers

My SHE4402UC/36 dishwasher malfunctioned all the lights were flashing and the machine was trying to drain. The guy came out and replace the control board. The dishwasher now read 199 on all cycles except the rinse and hold, the santitized light does not come when its done. The repair guy told me the count down timers were flakey on the the Bosch dishwashers and it would learn my dishwashing patterns in time. So 6 cycles later the dishes are still damp at the end of the cycle-the length of the cy


Well its not baloney but it is cheesey. normally changing the module is the cure but it has to be programmed correctly. bosch has a recall so check it out and see because the recall is free and the tech is suppose to know how to program it. go to the ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

When I press the start/resume control, the dish washer start/resume light blinks 2 to 3 times, then turns-off. then the dish washer beeps several times; however, the dish washer does not start. when turned the breaker switch off and on, and then I press the start/resume control, the dish washer go through a normal wash cycle. The next day when I press the start/resume control, the same thing happens. 2 to 3 blinking lights followed by beeping for several seconds. Dish washer does not start


... KitchenAid KUDC10IXSS Builtin Dishwasher

I have a Bosch dishwasher, model #SHU43C02UC/14, which has stopped working - no water enters the inside nor is there any drain cycle - just nothing. At the same time, I had to have the new control board put in as part of the Bosch recall. The tech comes out, puts in the new board - still nothing. He says something is wrong with the board even though the problem existed before the new board was installed. He takes everything back to his shop and tells me he's trying to contact Bosch tech support


... Bosch Dishwashers

The "clean" light blinks 8 times, then there is a pause, then it blinks once. The dishes are clean but not dry, as if it has not completed the drying cycle. We had an engineer out to fix it who said it was the circuit board and that the blinking light code indicated "too much suds", he replaced the circuit board, but it didn't make any difference. It's an intermittent problem: sometimes the machine completes its cycle OK. I ran it with just vinegar and nothing else in (no detergent, no dishe


... Kenmore Dishwashers

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

I have a Bosch dishwasher, stainless steel front- with buttons on the inside top( same as display, and the washing cycle won't start. Water seems to be running into the washer, as I can hear it, but the cycle never starts. Recently, I had clogged garbage disposer issue that has been resolved. The dish washer drains into the disposer, and I had free standing water left behind in the washer for 2days during this time.. Could this be the issue? Can you help me figure out this problem? Thanks!!


... Bosch 23 in. SHU 8805 Built-in Dishwasher

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

I have a Bosch dishwasher she44c05uc/40 It is 3-4 years old. Recently I noticed that the cycle times have gotten much longer. Since then there is a sewer smell in the washer especially when starting a new cycle it comes out of the disposal. I'm wondering if the pump isn't heating the water hot enough. I've also noticed that the dishes aren't getting near as clean as they were before all this started. Especially stuck on food. It used to clean everything now dishes almost need rinsed.


Hello,Welcome to FixYa ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a kitchen aid dishwasher model number KUD101TJBLO. I have had the thermal fuse replaced numerous times. It may run two weeks ir it may rub two cycles then the fuse blows. My serviceman has given up on finding a solution.He has replaced the control board and the door switch. However it continues blowing the fuse. I read on the internet that you need to replace the entire wiring kit that comes with the fuse but my repairman says this will not fix the problem and refused to replace the kit.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please check for the short on the wires near the heating element. Also check the resistance of the heating element, it should not be more than 1.6 K ohms. Also ma ... KitchenAid Dishwashers

MAYTAG MDB7600AWQ DIAGNOSTIC CHECK USING CONTROL BOARD AUTO AND MANUAL, ARE GIVING ME A HIGH CURRENT WASH MOTOR DIAGNOSIS.(NORMAL WASH FLASHING) THE BOARD ITSELF CHECKS OUT OK. ALL FUNCTIONS WORK AS THEY SHOULD.WASHER FILLS THEN ATTEMPTS TO RUN FOR (ABOUT 3 SECONDS) IT WILL DO THIS 3 TIMES THEN BOARD GOES BLANK. ALSO, THE WASHER WILL FILL WITH THE DOOR OPEN??? BUT WON'T ATTEMPT TO WASH. REPLACE WASH MOTOR?? THANKS lYNN


I would agree.. Here is a site for you to copy and paste in your address bar that I think will be helpful:http://home.howstuffworks.com/how-to-repair-a-washing-machine.htm/printable ... Maytag Dishwashers

I have a Bosch SGS66E02GB/45 that no longer completes a wash cycle. On "Auto 50C" time counts down from 2:58 to about 1:40 then goes back to the beginnnig and repeats. Spray arms are moving, it fills and drains, detergent is dispensed. I have checked the inlet and outlet pipes, the impellor and non-return-valve in the sump, checked the matrix is clear, checked to anti-flood float and switch and replaced the relays on the PCB. Selecting a rinse cycle will complete. Dishes are warm and wet rather


... Bosch Dishwashers

Hi I have a Bosch SGV46M13GB Classix dishwasher. Total cycle time is far greater than the displayed time and the water doesnt appear to be getting hot. I've checked the control board for any dry joints / damage etc - Nothing evident. Is there a wiring schematic available so I can check the voltage to the heater to confirm its the heater thats the problem before I purchase spares. Also, if I need to change the heater - Is there any guidance anywhere ?


First thing to do is check and make sure that it is connected to the hot water line. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

We have a n eight year old fully integrated asko dishwasher. Only the rinse cycle works, so I rinse many times - last rinse with detergent and then run the short program which does not wash, but will dry the dishes. The circuit board was replaced once before under warranty($500.00 labour) and I suspect that we may have to do the same again. Can we find this on the internet and do it ourselves; we have good electrical knowledge. Thank you in advance.


This is most likely an issue with the timer. Timers\015\012don't often fail. But if every other part of the dishwasher seems to be\015\012working properly and the timer knob seems to be stuck in one\015\012place--doing one function continuously--the ... Asko Dishwashers

Bosch she44c dishwasher. Dishwasher times down to 1 min and continues to run until until manually turned off. After further investigation the spray arm do not rotate during cycle. We have also noticed a decline in how clean the dishes are


Hello, Welcome to Fixya.. On bosch dishwashers the "1" is actually an error code and not coincidentally the reason it runs forever ( likely doesn't dry or clean well either right ? ). Here`s the most likely reason why it has detected the error... Eve ... Dishwashers

Bosch #SHE44C dishwasher does not fill. No power to the water solenoid, but power coming out of the control board and the emergency shut off float and switch is working. I need a manual with a wiring schematic and cycle sequence so I don't have to tear it completely apart to trace every wire. Thanks


... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Normal cycle time for a Bosch dish washer model # sgv53e43gb


... Bosch Dishwashers

Hello, Firstly, thank you for what you do, you help so many people and I know it takes time. I have a Bosch SHE44C06-UC Dishwasher. I fixed the E1 (Heating Circuit) error. First, before I found the writeup about the solder joint, I bougut a new heater and replaced it, ithe part included the element, flow switch and high temp sesor soall are new, then I fixed the solder and E1 went away and the cycle finsihes and the dishes are clean and dry. Still I check the error codes and still have


... Dishwashers

My Kitchenaid dishwasher (model KUDS02SRSS0) keeps burning out my dispenser. First I replaced the dispenser, then I replaced the control board and dispenser, it worked for two weeks and now I have a melted solenoid again in my dispenser. I've measured voltage to the solenoid and it is getting 110V through the entire diagnostic cycle. This is wrong. It should only get power at some point during the cycle to open the dispenser. It appears the control board has failed again and in the same wa


HI. The relay that controls the voltage and timed release command, via logic chip, is indeed damaged(stuck on). This is a common theme with this particular design. The original control board was recently replaced with a substitution model ... KitchenAid 24 in. KUDP01DLBS Free-standing Dishwasher

I have a Bosch SHU53513UC/U12 dishwasher. My initial problem is that the washer smells bad after a cycle and I've noticed some water sitting in the bottom of the unit. After running a diagnostic test, it results in a "2" heating fault. I followed your advice and used a current coil to and attached it to the GYBK-a1-3 hot wire on the control board. After running the test again, it only gets as high as 1.15A and manual says it should reach 11A. What should I do next?


Hello,Welcome to FixYa. ... Dishwashers

GE Dish Washer GSD 2800 DO3 runs a partial cycle...(even empty) and then beep and gives a message on control panel "washer arm blocked". Even ran without dish rack in washer still got the message. Push reset button and washer starts back runs a couple minutes and then stops and then beep and gives the same message on control panel "washer arm blocked" again. There is "NOTHING BLOCKING" the washer arm!


The rotating arm has a magnet in it to let the controls know if it is turning. Yours is not turning so \012\012\012\012check the jets for blockages... you might have to remove the arm to clean them properly ... Dishwashers

Bosch dishwasher Does not heat up in the washing cycle and does not drain down at the end of the cycle. End of cycle the display sticks at 1 and the drain pump operates until the machine is switched off or reset. Followed the suggestion in another thread to look for a burnt solder joint on the control board. Unfortunately my machine is a later model than the board shown and has no poor joints on the board. It would seem from previous answers that the problem is either the controller, the heating


1) The water must be preheating by heating elements and thermostat see how to do it.\015\0122) Timer , test for defective,clean the contact, repair wires for loose, broken, or burn.\015\012\015\012God bless you.\015\012 ... Dishwashers

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1634 seconds