Having problems with your Bosch Dishwashers ?
Bosch dishwasher white wire connection in machine terminal box got hot and melted the wire nut.
Repair Help & Product Troubleshooting for Bosch Dishwashers
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Bosch dishwasher white wire connection in machine terminal box got hot and melted the wire nut.
... Bosch Dishwashers
Bosch she3ar76UC/07 In the box where the house current is connected , the load wire (white) has been hot and insulation burned. No visible damage on the back side feeding the dishwasher. Cleaned up the white re connected, have power, dishwasher will not turn on. Any ideas, is there a fuse somewhere? Thanks
I am installing a Kenmore dishwasher model 13743. I have direct wired the washer?s terminal box wires to the wall power via a BX wire and the washer doesn?t respond. None of the panel buttons are active. With a multimeter, I find that there is voltage on the wall wires and on the dishwasher end of the BX cable wires that hard wired to the wall current. Even though, when I connect the dishwasher?s terminal box wires to the BX wires as directed in the Installation Instructions (white to white,
Next step to check the door switch...the door must close and the switches on the door must close to send power to the control...let me know ... Dishwashers
I'm attempting to reuse a Maytag dishwasher motor for a bench grinder. Since this is a reversible motor, I'm not sure how to connect the wiring to a simple switch so that it works in one direction only. The motor has 4 wires: blue, gray, red, yellow. Not sure which to connect to the hot (black), return (white) and ground (bare) wires from the romex and can't find a wiring diagram online for this dishwasher. Any ideas? Thanks.
... Hobart 29 in. AM15-1 Free-Standing Dishwasher
HI. Trying to install a LDF6920ST Dishwasher. Question about the wiring. The wires coming out of the machine are Black, Green with a yellowish stripe and White (the white one has a label attached to it with a "N" on it). The plug wires are 3 side-by-side. They are gray, green and gray. Which wires do I connect with which wires?.
... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher
While installing maytag dishwasher mdbh949awb, a wire became unplugged under the machine; noticed it dangling down after all water, drain etc. were connected. It's a brown wire; 2 strand; it has a white plastic plug/connector on the end. Any proposed solutions, short of removing the machine and starting over, would be greatly appreciated Thanks.
... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher
We have a Bosch SHU9925UC dishwasher, installed in 2002. In August 2010, the water didn't drain, and a service technician discovered melted wire nuts at the main incoming power junction, presumably due to a loose connection there. He re-wired it. Now it's March 2011 and yesterday we smelled electric fire smoke coming from the dishwahser, opened it up and again found melted wirenuts. So is it really just poor installation, given that now 2 different installers have created the same problem?
... Bosch SHU9925UC Built-in Dishwasher
I'm installing an electrolux dishwasher, the first thing I'm going to do is the electric wire. I know I have to attach the black white and green (ground wire).I've done this before with my Maytag and it was a breeze. When I open the elec. box on the electrolux dishwasher the black white and green wires go into the box from the Dishwasher and then THROUGH THE BOX AND THEN BACK INTO THE DISHWASHER>>>>>THERE IS NO END........... In the Maytag I just opened the box on the dishwasher and the ends of
There should be a complete wire connection already there ready to be plugged in. If not, typically at the back of the unit there should be a black plastic box that when opened will indicate 3 terminals. live - neutral - and earth. Looks to m ... Electrolux Dishwashers
Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un
... Bosch SHV4803 Dishwasher
I wired a ge dishwasher ..white to white and black to black. the ground..green wire a screwd to the dishwasher.. turn it on and everything worked ok til the pump came on and the the black to black connection overheadt and starte a fire.... what did i do wrong...note my house wire has only white and black...thanks
Well, hard to say at this point. Your wiring sounds correct, but there may be some other stuff going on which you may have not anticipated. First off, what size breker is attached to the wires you connected to the machine. Most household machine requ ... Dishwashers
Bosch APEXX model number SHY99A05UC/14 lost power. Power input line appears to have arced (white power line and wire nut show signs of stress). The power breaker did not throw at the junction box. Already cut back wire and re-attached new wire nut along with replacing the breaker at the junction box. Still no power. There are no other visible signs of power stress or water damage underneath the unit or inside the doo panel.
I do not have access to the user or service manual for this model.\015\012However, such symptoms could be result of heater element or thermal overload fuse blowing. Do you remember having a very hot dishwasher when the it lost power.\015 ... Bosch Dishwashers
I need the steps to change the hose assembly on my Whirlpool portable dishwasher. When I got it someone had cut the sink connections off so my son connected it to the water and drain with my washing machine which was in the kitchen. However, I have moved and want to use it as portable. I purchased the new hose assembly for the sink faucet, I just need instructions on how to take the dishwasher apart and connect the new hoses.....HELP PLEASE!
... Whirlpool 24 in. Portable Dishwasher Dishwasher
Dishwasher fills with water and then stops. No lights are on at all. I cked wiring and circuit breaker and no issues there. I then flipped off circuit breaker over night. Got up next morning and flipped breaker back on. Dishwasher lights were on and when I pushed Start button, it ran fine. Now it is doing same thing except circuit breaker trick dont work like last time. THERE is NO issues with wiring or connections to dishwasher.
... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher
My dishwasher did not come with power cord. what kind of cord do it need and how do i connect the cord? On the new cord how will i know which one to connect to the white and black wire? The dishwasher is Whirlpool model du930pwsb, Sku numbmer 451-5344.
120 Volt 16 gauge, 3 wire power cord.\015\012\015\012Brass Screw is Black, White Screw is is Common, Green is Ground....Try Home Deport for a cord. If no screws are on the dishwasher, use wire nuts and elec. tape ... Whirlpool 24 in. DU930PWP Built-in Dishwasher
There was a short in the junction box. i fixed that by stripping wires and installing new wire nuts. the dishwasher ran. for some reason the water is NOT entering the dishwasher
There is a chance that the coil on the fill valve has become bad. If the valve was being operated at the time the short occurred the coil could have overheated and burnt up.A couple ways to check it would be;\015\012\015 ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher
My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14
The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher
I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a
The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers
Moved my dishwasher and the wires came off need to
... Kenmore 24 in. 16269 Built-in Dishwasher
GOT A KARCHER HDS755 BUT THE BURNER DOES NOT WORK.IT HAS FUEL GOING TO THE NOZZLE AND HEAPS OF SPARK.WHEN I OPERATE THE MACHINE WITH THE BURNER SWITCH ON AND FUEL LINE DISCONNECTE FROM NOZZLE,MACHINE WORKS FINE WITHOUT HOT WATER.WHEN RE CONNECTED,THE MACHINE WANTS TO CUT OUT.
Hi Please check your oil zzle is not blocked at all. Remove the burner head and renew the nozzle. If that fails you will need to check the fuel pressure from your fuel punmp which should be at least 9-10 bar. ... Pressure Washers
We have been given an indesit IDL40 Dishwasher It was given with a hot (red) pipe, but I suspect it may have been the only one they had I only have a hot feed available as the washing machine is plugged into the other Can it be connected to a hot feed or do I need to get my plumbing gear out?
Have a 15 day old Thermador Dish washer direct wired to the circuit breaker, replacing a DW that was there for 10 years. Wiring is the same age. The unit will not turn on and I took the cover off the electric cover the hot wire had melted the connection. what's going on? model DWHD630gcm
... Thermador DWHD630GCP Dishwasher
Which of the two wires conecting power cord in dishwasher is the hot wire
... Kenmore Dishwashers
We have a 6 year old Jenn Air dishwasher model JDB2150AWP We had a cracked door close unit which we replaced but got a short while restoring connections I am wondering if there is an internal circuit breaker, relay or fuse on these machines that we need to check and possibly replace since we cannot get it to run at all. No power or lights at all. I believe all connections are secure and we replaced the door close unit with new parts.
... Jenn-Air 24 in. JDB2150AWP Built-in Dishwasher
I have an Asko DW1875 dishwasher (10yrs old) which has just recently started having problems. The initial symptom was that during a washing cycle, unit showed '1' and inside became very hot (melting some plastic cups/plates in unit). On further investigation (with diagnostic mode), the dishwasher is filling and draining with no problem. When circulation pump runs there is barely any water pressure in blades (just dribbles out) and water leaks into undertray via a plastic white tab near front (v
... Asko D1876 Dishwasher
BF41 Dishwasher with a leak stuck in mid cycle Hi, I have a 'general domestic Appliance Ltd' BF41 (95+G709394) dishwasher which recently started leaking at the door. After replacing the seal the problem seemed to ease, then recently the problem started all over again and the leaking got worse. A couple of day ago I couldn't stop it leaking and now it's stuck in mid cycle and even though the water is washing inside the machine it never gets hot inside or finishes the cycle. Ive tried stopping and