Having problems with your Bosch Dishwashers ?

Machine doesnt start . when on button is pushed and regular wash button is pushed it goes to agent and cycle is at 0 flashing (both 0 and agent lites).have tried to shut it off and main switch and turned it on and off a few times. and still the same


Answers :

Because the timer controls many operations, a faulty timer can cause many problems. The timer is a complex component, so you shouldn't attempt a do-it-yourself repair. Test the timer with a VOM set to the RX1 scale. To gain access to the timer, remove the front control panel. The timer is directly behind the main timer control knob. Disconnect one of the timer's terminal wires and clip one probe of the VOM to each terminal. If the meter reads zero, the timer is working. If the meter reads higher than zero, the timer is faulty and should be replaced. 
ec47068.jpgBecause the timer controls many operations, a faulty timer can cause many problems. The timer is a complex component, so you shouldn't attempt a do-it-yourself repair. Test the timer with a VOM set to the RX1 scale. To gain access to the timer, remove the front control panel. The timer is directly behind the main timer control knob. Disconnect one of the timer's terminal wires and clip one probe of the VOM to each terminal. If the meter reads zero, the timer is working. If the meter reads higher than zero, the timer is faulty and should be replaced. 
\015\012\015\012\015\012The timer is connected to several wires that supply power to operate the various functions of the dishwasher. To replace the timer, have a helper hold the new timer next to the old one. Connect the wires of the new timer one by one, removing the old wire and connecting the new, to make sure you connect the wires correctly. The wires may be friction-fit on the terminals. If they are, use long-nosed pliers to remove the wires. Don't pull up on the wires, or you may break the connection between the wires and the clips. After connecting the wires, set the new timer in position, secure it the way the old one was secured, and replace the control panel and knobs.
\015\012If your dishwasher won't fill with water properly or isn't drying the dishes, you most likely have a valve or heating element problem. In the next section, we'll discuss how you can assess these types of problems.
\015\012rate it tanks,,,,,,,,,,,,,
Try unplugging power cord for fifteen minutes first, see if this clears the error.
Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Machine doesnt start . when on button is pushed and regular wash button is pushed it goes to agent and cycle is at 0 flashing (both 0 and agent lites).have tried to shut it off and main switch and turned it on and off a few times. and still the same


Because the timer controls many operations, a faulty timer can cause many problems. The timer is a complex component, so you shouldn't attempt a do-it-yourself repair. Test the timer with a VOM set to the RX1 scale. To gain access to the timer, ... Bosch Dishwashers

The Bosch plastic push button (AP2804452) has broken on my SHU9950 dishwasher. The switch itself is still good. I have removed the broken pieces of the bad button from the unit and am now depressing the switch without the button. When I get the new push button, what is the proper way to remove the control panel cover to put the new button in place? Thanks!


... Dishwashers

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

Asko D3530. Program LED does not come on. Also nothing happens when I push Set, Menu or Start. Tried button on the left (cirle with a I, looks like a reset button?). Checked plug, GFI and circuit breaker switch. Still no power and no light no response from various buttons.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012It sounds like you've got a bad power switch or a wire at the power switch or as you described it... (circle with a I, looks like a reset button?) ... Asko 24 in. D3530FI Built-in Dishwasher

I have a magtag quiet 100 series that has a broken handle but still shuts tight and seems to lock yet. Problem seems to be that the rinse only light will stay on for quite a long time and won't let me hit the wash button. When the rinse only light does go off, if I hit the wash button it starts but then switches to rinse only. Sometimes I can get lucky and get it to stay on wash after the rinse button is off for some time. Any suggestions?


... Maytag 24 in. DWD1500A Built-in Dishwasher

The dish washer ran its full cycle but won't shut off. the little pump motor in the very bottom keeps cycling water in the bottom. it won't shut off when you open the door, it won't shut off when you push the power button and the front switches won't respond. the little light on the front of the dish washer is blinking and it has never done that befor normally the lites are always on solid.....


The drain stuck cycle ( I presume you mean drain pump running constantly ) are directly related with overfill scenarios for Asko dishwashers of this ... Asko D3122XL 24 in Builtin Dishwasher

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

I have a maytag mdb6650 aww dishwasher. The dishwasher just stopped. The light on the control panel is on. If I push the buttons to try a different cycle, the light over light wash remains lit, so the buttons don't seem to respond. I was wondering if it is the control assembly, or if the door switch is not working. The handle cracked a while ago, but if the dishwasher still worked even though the handle had cracked in half.


... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Our dishwasher came with our house. Brand new. It is 2 yrs old now, warranty gone. The problem is when you shut the door the machine starts running immediately and keeps running and running and running. You can push the stop button, delay button and it still runs. Also, doesn't clean. model# FDB1050REC4


... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Normal wash cycle- tub fills (?), then comes a loud hummmm and nothing happens. I noticed water level didn't reach heater coil and added water until limiter switch clicked. Still just a loud hummmm. Machine was well into its regular cycle when this first occurred, but now, won't even get past initial fill. Pushing the "Cancel/drain" button activates motor and pump: they work fine.


You are an expert enough reading this. But with a terrible complicated dishwasher. First clear the waterlevel problem.\015\012Rest is a result. You do not need me, join us. Next time buy something more plain. ... Dishwashers

Have a Whirlpool Dishwasher 6ADP 5540. Starts cycle - fills water then about a minute into it the start buttons flashes 6 times and will not continue on. Very rarely, the cycle does continue on. Have turned off at the main switch. But still have this problem. Look forward to your reply. Cheers, Jodie


Hi Jodie,\015\012\015\012An F6 fault code - indicated by the green light flashing in sequence next to the start button - is indicative of a water inlet problem. \015\012\015\012First of all check that the water tap the dishwah ... Whirlpool 24 in. ADP6940 Dishwasher

Kenmore Ultra Wash dishwasher model number 665.1374 or 665.1384 I am a technician. This unit does nothing. It has power and ground. I have tested the door switches. They test good. If I unplug the unit and plug it back in then it will run a drain cycle, at least that is what I think it is doing. The motor runs for about 4 minutes. Once it shuts off, there is no further response. No control indicators illuminate. No response from pushing any of the touch buttons.


... Dishwashers

Ge nautilus beeping blinking light over normal button. When push start/reset, stops for a minute but then begins again. Tried shutting power off for 30 seconds but still no fix. Any suggestions? Thanks!


... GE Nautilus 24" Built-in Dishwasher

My push button on off switch on my smeg df612sdx has dropped off and has now been chewed by the dog, the mech behind the switch stil pushes in and out so it looks like i need a button?


... Smeg 24 in. DWF612SS Free-standing Dishwasher

I have a Frigidaire Gallery dishwasher model number FDB989GFC2. All of the indicator lights on the right side are flashing (Controls lock, add-a-dish, washing, etc.). when buttons are pushed I get no response. Have tried turning off at circuit breaker for 1 hour, when powered back all lights still flashing and still no response from pushing buttons. Any ideas?


You need to rpelace the electronic control board ... Frigidaire FDB989GF Dishwasher

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

I have a Whirlpool GU1100 built-in diswasher that will not clear the pot & pans selection. It is stuck with the pots & pans and the cancel buttons lit and blinking. It will not start or clear. I have tryed to shut the power off for awhile and this has not helped. Other buttons can be pushed and will light but the other two remain blinking. If the clear button is pushed it will clear the other button but not the pots & pans or itself. Is this a problem I can fix myself?


... Whirlpool Dishwashers

After the dishes are done washing, you cannot shut off the washer by pushing on the drain off button on the touchpad.The touchpad is all cracked in front of the button


Warn out close sensor arm. Locate it on door and put a small sticky pad on it to push sensor switch a bit farther. If that works, the adjusting the sensor switch position may be necessary. ... Maytag MDB7100AWB Dishwasher

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

I've tried to use this new machine 3 times. Each time it was never turned off until I pushed the cancel/drain button. Once I let it run for 2 hours before turning it off. This evening I tried the rinse only button and when I checked on it,it had switched to the normal wash cycle. Then I pushed the cancel/drain button.


If this is a new machine and it's under warranty, Have a technician come out and repair it as soon as possible. then fully test it's operation after he is done fixing it . It sounds to me as though it ... Whirlpool Gold GU2275XTV Builtin Dishwasher

I have a Kenmore dishwasher model 66574362K2. It has worked fine until tonight. I opened the door before the end of a cycle, closed the door, and pushed the cancel drain button. There was still water in the bottom but the dishes were basicly finished. Now I can not seem to get the dishwasher to come back on. The lock button seems to be on and it usually is not on. The manual says to push and hold the button for 4 seconds to turn it off. I did that. But now it is flashing between the Heate


Can you press the drain button to drain the water, then shut the unit off and restart??? I have exhausted all my resources to help, thought this may work. ... Kenmore Dishwashers

Hi, Just moved into a place with a DU4500B Magic Chef. After a cycle there is still a clump of wet soap in the main wash cup dispenser and the dishes aren't clean. Yesterday I tried putting the soap in the pre wash and and main wash dispensers but leaving the main wash soap dispenser OPEN rather than clicking it shut, and there was still left over soap in the dispenser and granulated soap residue on the dishes and they weren't clean. Many thanks for your help.


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Magic Chef 24 in. DU4500 Built-in Dishwasher

The clean light keeps blinking and the dishwasher will not start. I pushed the cancel button and it runs for about 30 seconds and just shuts off. Nothing happens when you push the start button.


HiIf clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If ... KitchenAid Dishwashers

I have a bosch SHV43A03GB dishwasher. It has a problem when it cut out water flow in. the guy who repairs it seem s only to have to push a button or switch under the machine to get it to work again, cant find switch/ button- please help!


Programmer not working ... Bosch 24 in. SHU53 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1225 seconds