Having problems with your Bosch Dishwashers ?

Bosch SMS4012 - E-NRSmS4012AU/11 FD7309041276not sure of its age but this dishwasher wont commence its cycle when I turn the left dial (but If I hold the handle latch up, it starts) there is no error code facility on this unit. Would it be worthwhile getting a technician to fix it or should i just buy a new one !! Thank you - Rena.


Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch SMS4012 - E-NRSmS4012AU/11 FD7309041276not sure of its age but this dishwasher wont commence its cycle when I turn the left dial (but If I hold the handle latch up, it starts) there is no error code facility on this unit. Would it be worthwhile getting a technician to fix it or should i just buy a new one !! Thank you - Rena.


... Bosch Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

Dishes are not getting cleaned after cycle. Glasses are smoky after cycle and I noticed that the upper spray arm appears not to spin. What would cause upper spray arm not to spin? Is this something I can fix or do I need to have a technician fix it?


Hello kharyespy,\015\012 First we have to address the obvious. Are you making sure that there aren't any large spoons sticking up from the silverware basket. Are there any objects hanging down from the top, or from any where ... Jenn-Air Dishwashers

Getting an F1 code. Online search indicates I need to call in a technician because Flood switch has been activated. No water leaking anywhere. Is there anytihng else that would cause this code to appear?


Yes, we had this problem until we started using the high efficiency detergent. If you put to much in, it will overflow and cause the F1. You can fix an F1 by taking out the bottom drawer (unplug first) and drying out the control board (it is under ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

MY FATHER IS WORKING ON A LXIH HOBART. THE UNIT IS SHOWING ERROR CODE E173. IS THERE A WAY I CAN FIX THIS PROBLEM OR A WAY TO GET THE ERROR CODES.


Hi,\015\012\015\012This is what I found in the manual...and on a couple of other sites....Machine won't fill or won't fill high enough(LX18, LX30 display shows "E0," "E2," "E3," or "E4")1.Low water pressure — ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Rats got into the heating coil and ate away the insulation. How and where do I get that fixed? It's a Northstar 3,500 OSI hot unit. My zip code is 28226 in Charlotte, NC.


Any of the companies listed below can help you and are located in your area. These are all trained and certified service centers that specialize in pressure washer repair among other things.Sincerely,Aron KerrLanda Northwest ... Northstar Pressure Washers

Bosch SHE44c getting a E6 code????Just finished E1 code by re-soldering the board and the first wash after fixing that error, I get an E6 code and it did not drain. During the repair of E1 code, I cleaned all hoses out and made sure I had no problems...What is the troubleshoot to search for E6 code?


Thanks, that perfectly nailed my problem. Bad / burnt solder joint on a SHX45P05UC/57 model. A little solder, and it may last a while. But next it fails that way I can order the motherboard without even opening it up. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Danby ddw497w will only be about 5 min into cycle when digital code E2 appears it then starts beeping 2 min after this it just stops the unit is only one day old it ran once yesterday fine now i get this code no matter what cycle it is on I bought mine new off the internet and it's been running great for about 2 months. Now I can't get it to drain and E2 shows, I can't get my money back because I've had it more than 30 days, if the solution is a pump, I'm tossing it and getting a good one from


E2 is a hose issue. There is either a kink in the hose, the hose is too high to drain or the pump is faulty.1-800-26 DANBY ... Danby DDW497W 22 in. Countertop Dishwasher

Mod. mdc5100aww ser. 28126829ax purchase date dec. 02 i called the serviceman he said the sprayers are pluged. i'm on a fixed income. with food house payment medicine dr. bills. i can't afford to get it fixed. i tried to get the bottom sprayer off. i could not get it off. now i have it unsnapped & can't get it back together. if you can help me i would appreciate it!!!!!!


... Maytag Dishwashers

My dishwasher will not drain. it goes through the first 10 minutes of a program then i get the OE error code. i have checked my hose for kink or clogged-there is none, i have made sure it was level. i would like to get the filter off but it looks like i would have to take the drain pump out from the bottom to check if any thing is plugging it. was just wondering if anyone has any tips that would help. thanx


1)check the drain pump working\015\0122)check any block from drain pump to drain hose. ... LG LDF6810 Built-in Dishwasher

I have a Bosch SHE56C05UC/40. The unit fills and drains ok but the circulation pump will not operate. I run the diagnosis according to another of you posts and came with an error code E1 which is a heating code. Why would this prevent the pump from running? Your diagram show a flow switch in the heating circuit which won't close unless the pump runs. A diagram of the pump circuit would helllllp.


Follow the instruction code in your ins.manual if you do not have go for free download : www. fitness.manualsonline.com or www.ret ... Bosch SHE56C02UC / SHE56C06UC Dishwasher

Kitchenaid kuddo1dppa I own a KitchenAid KUDD01DPPA, 2 drawer dishwasher. I am not a technician, however I have had a lot of experience in repairing various appliances and am savvy with electronics and mechanical technical issues. Here's the problem: I was getting rinse error codes in both drawers, pulled the bottom drawer out, removed the cover to the circuit board and used a dryer to dry up the moisture on the flood switch. Now I am getting Fill Failure error code on both drawers. I have g


Test this steps and fix it. God bless you\012 \012 Water Inlet Valve\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

Unit would not drain, found soapy water in unit. Checked for obstructions...None found...start cycle then hit cancel/Drain and nada...no noise, no drain...nothing...Entered the diagnostic mode on the unit and reads E1 which describes a heat problem?????Pretty proficient at fixing things, need a little guidance...Please help...


Hello,\015\012\015\012Welcome to Fixya.\015\012\015\012\015\012I can provide you with a complete service manual in a "pdf" attachment, but I`d requre a email address.\015\012\015\012I know what the problem is ... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher

Electrolux 1113312-20 Hi - my dishwasher circuit board has burnt out (melted) and i need to replace this section. The details on the unit state:- Computime CODE: ELE4157 Electrolux CODE: 1113312-20 Hardware CODE: 156050732 SW: DMA24_MR 230V/roHz T65 Date: 09-281 Can anyone help to advise the best place to get one


... Electrolux Dishwashers

We have a 100% failure rate on multiple parts on two Maytag dishwasher units and no longer can get replacement parts from anyone. Any ideas of what to do? Here is the latest summary we sent to Maytag: Thank you for the help last fall. As a follow-up, we are still having very bad results with your product. You authorized replacement of the unit which was done. After one dishwashing, THE NEW UNIT SHOWED THE SAME PROBLEM (WOULD NOT TURN ON). I called in and you referred us to a senior te


Well iam sorry to here of you major problems.if the control board has been replaced several times and no luck fixing it there may be a problem with the main power supplied to the unit,as well as having a problem with the wiring harness.usually a manu ... Maytag 24 in. MDBH940AW Built-in Dishwasher

I have the "rinse" error code on my kitchenaid double drawer dishwasher kudd01dppa1. I've turned off the power, then it worked for one load and the code reappeared on both drawers again. What should be a next step? it says in the manual that the "rinse" error code means that something happened to the flood switch...? Can this be fixed without calling out the kitchenaid technicians? thanks


... KitchenAid 23 in. KUDD01DPPA Stainless Steel Dishwasher

I'm getting a PF power interupt code. When I press the "Start/Cancel" button the code goes away. Unfortunatly the unit will not power up. It appears to be completely dead. If I cycle the breaker the PF code comes back and we start the process again. What's wrong, help!! Bob


Hi,If pressing the cancel button doesn't get rid of the power failure error\015\012 "PF" then you have a bad control board. So you will need to replace \015\012the control board itself.You could try to disconnect the power su ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Hello, I have a Fisher Paykel Double dishwasher (DD-603) - about five years old and then top unit is literally going nuts. It turns itself off and on, beeps constantly, and will not run through a cycle. What is causing this issue and how can I go about fixing this problem?. What parts do I need to buy? How do I remove the front panel of the dishdrawer to fix this problem? Do it yourself repair instructions would be terrific.


It sounds like it needs a new computer board (the whole thing) so you cant do it yourself it needs to be orded in. \015\012\015\012If you have any questions please dont hesitate to ask ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

FDB750RCC1 When I start the DW, the motor hums loud then soft then loud then soft...if I advance the dial some sections of the cycle nothing will be running and others the motor is on, but no water is getting into the unit. I just replaced the inlet valve and solenoid and that didn't change anything. I can see water in the recirculating pipe running up the unit, but it will just try to make it up and fall back down. Not sure how to proceed...my thoughts would lead me to the main motor, but


Can you hear the water solenoid click when it calls for water? If so, check that the water source valve is on and water comes out of the valve. Check the entry hose for kinks. Remove everything under the lower arm down to the deck keeping track ... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

I have a new Bosch Dishwasher.I just turned the Unit on and 10 Minutes into the Wash Cycle it comes up with Error Code E 16. There is no information in the Operating instructions about what this means or how to fix it. I have been on the phone for 1 hours on hold listening to elevator music after ringing BSH Home Appliances Pty Ltd Customer Care I just install in using the Installation Guide. I have 20 years experiance in Appliance Repairs. Does anyone know what E 16 means and what is the fix.


... Bosch Dishwashers

Hi where can I get operating manual for Siemens ecosense dishwasher. recently bought property and appliance was already installed. Previous owner did not leave a copy and i now get E24 error code, with water remaining in base of unit - assume something to do with waste pump or pipe?!


... Siemens Dishwashers

I WAS LOOKING FOR A SHORT DISWASHER TO REPLACE MY 32" HIGH DISWASHER WHICH LEAVES WATER AT THE BOTTOM AFTE R THE CYCLE HAS FINISHED. IT DOES NOT LEAK. OTHER INTERNET SITES HAVE CONFIRMED THAT A 24" WIDTH WASHER IS IMPOSSISBLE TO REPLACE AT 32" HEIGHT. DOES THIS DISHWASHER SOUND LIKE IT WOULD BE WORTHWHILE TO FIX AND WHAT WOULD BE INVOLVED?


... Hotpoint 22 in. 7892 Built-in Dishwasher

I have a hobart lx-g model which i purchased used a month ago. At the start everything worked great...then when ever i would push the "off" button it would shut down and restart by iteself... lately i've been getting lots of error msg's (one was E4...) and now it overflows all the time, its as if it's gone banana's... what do I need to do to fix my problems (chane the cpu???)


Hi,Initially would suggest to check that the power supply requirements are satisfied. You might also need to check the breakers. Depending on the exact model number, the AC supply can be as shown below: ... Hobart Dishwashers

Sometimes the cycle would get stuck (like transmission not working). Now making noise but not taking in water to wash. Machine about 8 years old and used daily. Isi it worth fixing? Sevice call is $140 plus parts and labor. If not what would you buy in its place? SHU3032UC/UC12


... Bosch 24 in. SHU30 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1403 seconds