Having problems with your Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher ?

My Bosch dishwasher, model SHE58C did not completely drain. We were eventually able to use the cancel cycle/drain procedure to get the machine mostly drained, but now all the lights are lit on the panel, and the count down display is 11. I haven't figured out how to reset. I have tried to hit "Cancel drain" and turn on the machine to get into diagnostic mode, but I can't figure out what the codes & light combinations mean because my model is not in any of the online sources I've found


Answers :

I have managed to pick up typical diagnostic error codes for a bosch dishwasher - these are
\015\012
\015\012

0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault
\015\0121 = Aqua Sensor ("Sensotronic") fault 4 = Filling fault F = Filling fault (display occurs during wash, not test)
\015\012
\015\012If more than one fault then the codes are added. So 11 in your case would mean NTC, Heating and Aqua Sensor fault.
\015\012
\015\012Coming back to the original problem of not being able to drain. Do you know if the wash cycle was complete when you realised the dishwasher had not drained?
\015\012
\015\012I am beginning to get the impression the original problem was linked to the dishwasher shutting down due to a heater fault. Either the cycle timed out as the water was not heating or shut down because the NTC (temperature sensor) failed.
\015\012
\015\012The assembly diagrams of your dishwasher can be viewed at this site.
\015\012
\015\012Hope this helps.

Since\015\012 the drain pump will pump the water out using the "cancel/drain" button,\015\012 if it did not work then your problem is likely to be in the drain hose \015\012system or the garbage disposal downstream from the drain pump. Check for\015\012 kinks in clogs in the drain hose. Grease can build up in the portion of\015\012 the drain hose just before it attaches to the garbage disposal.

If\015\012 you are having problems getting the water to drain out of your \015\012dishwasher then there are a few things that you need to check out.

First\015\012 check the drain hose that it has not gotten pinched anywhere. Then \015\012check it to see if it may be plugged with dirt and debris. If you have \015\012it hooked to a garbage disposal make sure that the hole into the garbage\015\012 disposal is open.

If all of that checks out, then check the \015\012screen inside at the bottom of the dishwasher. Excessive food buildup \015\012will block the flow of the water into the pump.

If that is clear \015\012then you may need to remove the bottom rack, and the bottom spray arm. \015\012This will allow access into the pump. Some dishwashers have a diverter \015\012flap that opens to allow the water into the bottom impeller, which is \015\012the pump out impeller. Also check that the bottom impeller is in good \015\012shape and not deformed. The switch that operates the diverter flap can \015\012also go bad. You need to check that it can operate and that is does if \015\012power is applied to it.

By checking all of these things you \015\012should be able to find your problem. You may have to take the time to \015\012eliminate the problems one by one till you get to the cause of your \015\012problem.

Check the below link for an detailed description

http://www.fixya.com/support/r4078724-dishwasher_problems_water_will_not_drain

COURTESY:heatman101 -A senior Expert in fixya..
Repair Help & Product Troubleshooting for Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch dishwasher, model SHE58C did not completely drain. We were eventually able to use the cancel cycle/drain procedure to get the machine mostly drained, but now all the lights are lit on the panel, and the count down display is 11. I haven't figured out how to reset. I have tried to hit "Cancel drain" and turn on the machine to get into diagnostic mode, but I can't figure out what the codes & light combinations mean because my model is not in any of the online sources I've found


I have managed to pick up typical diagnostic error codes for a bosch dishwasher - these are\015\012\015\0120 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault\015\0121 = Aqua Se ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Anyone have experience with a Fisher Paykel double draw dishwasher (model DD24) getting stuck in wash mode? Once it hits exactly 48 minutes it stays there. Only several hours later it cycles through OR you have to turn it off put it in rinse mode to complete. Already tried all the basics (unplugging, no fault codes, cycled through the diagnostics everything good and working). Did the quick diagnostic cycle of 14 minutes and everything cycled through fine. Next step will be to put the bottom cont


... Fisher and Paykel Dishwashers

How do I get anto the diagnostic mode for model # GU3100XTVS Whirlpool dishwasher


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Model mdb8959saso. Recent power failure caused cancel/drain light to blink rapidly. Only way to get it to run is by putting it in diagnostic mode and waiting for codes to stop.Do I need to call for service every time power is interupted?


... Maytag Dishwashers

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

Hobart commercial under the counter diswasher LXIC Model Number 130016. DELIME light comes on every day at startup. Machine will immediatly run (in DELIME mode I think) for about 5-10 min and then get E4 error. We unplug power to the unit let it set, replug it back in after 3-4 cycles of this, it will eventually work perfect for the entire day. I have replaced the Sensor that is on bottom front of the unit in the water trough. ( I replace the sensor to the right if you are looking at the un


Q have your run a descaler . to rid the machine of its deposits . in order for the machine to run properly the parts and pump / screens must be clean . / descaling for deliming . dishwasher and icemakers is comm ... Hobart LXIC-6 Dishwasher

I am not able to get a siemens front loading washing machine at the right price. first they told me that the model was not available now the price of the model in india is too high for the features that are in it. I doubt whether it is a siemens model itself. kindly call me on 8975764416 immediately please. i tried to contact the england phone number also but it was wrongly given in the website of siemens. please help me to get WM14S79BUK or WM14S794ME model of washing machine at the right


... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

Hi, I get a problem reading " E4". I have now switched the machine off and on again, but still it says the same. Incidentally the machine has already pumped the water out, so the 'overfill" is actually not supposed to be a problem. It is KELVINATOR EXTREME CLEAN DISHWASHER, model KD14SS. Please help, how am I to get rid of this problem, I really do not have the time nor the money to get outside help! Anita Kleynhans


... Kelvinator MDP531RF Dishwasher

I have a whirlpool dishwasher model 980 that starts washing normally, but does not continue through the remaining cycles. Is there a way to get the machine reset?


... Dishwashers

Just got a used F&P Smart Drive 5.5 MW059. First few times I used it wouldn't always start on certain settings but once it did start it ran through just fine. On the fourth use, it was very difficult to get it to start and it just stopped after it filled up. Pausing and restarting, shutting of machine and retrying did not help. Was able to advance to rinse mode and got machine to drain water; however, instead of going into spin mode it just attempted to drain continously. I let it do its th


Did not realise this is a washing machine and not a dishwasher.\015\012\015\012Looks like some consultant has already been dealing with you on this problem.\015\012\015\012Hard to say if it is a simple as an inlet solenoid val ... Dishwashers

Gaggenau GM 915-710 UC6 dishwasher will not fill and wash. Close the door, turn lever. Empties water from sump. (drain hose was not clamped above disposal outlet nipple, fixed that) Machine empties sump, but will not stop after sump is dry. Will not initiate fill and wash. Manually stop machine. Can't get control board to do the diagnostic to get an F #. Pressing button 1 and 3 at the same time. A couple of the plastic tabs on the circuit boards plastic support housing that link the


... Gaggenau GI936-760 Dishwasher

ELS63010/S-No 91210714 Electrolux Dishwasher On Controls Top Red Light is flashing.I am unable to get back into normal program mode,and i am not certain if machine is filling. How do i get into setting mode


... Electrolux 23 in. ESL624 Built-in Dishwasher

Kitchen Aid Dishwasher - model: KUDPO2CRBLOrn Ran the dishwasher twice on pots/pans cycle and sani rinse with a special cleaner recommended due to build up and items not getting clean. (soap left all over them) Cleaned machine out great! Now, the only choices that will light are "quick clean up" and "rinse only." Even if I choose them, when I hit the "start" button - the machine will not start. No other lights will light. Machine will not start. Any ideas?? Thank you!!!


... KitchenAid Dishwashers

Model SHE68P02UC/60 There does not appear to be a drying heating element in this dishwasher or did we miss connecting something up during the installation? Unsatisfactory drying on both "normal" cycle and "auto wash" cycle.Drying agent is in machine. What is "condensation drying"? Is this just blowing cool air through the machine and out through the vent? If so it is unsat. How to get the machine to actually DRY the dishes? I'm going to be very disappointed and out over $1,000.00


I am assuming you have the dishwasher connected to the hot water tap which can give water at about 40deg c (120deg F).\015\012\015\012The dishwasher uses steam from the water (after heating it further). So if the inlet water temperature i ... Bosch Dishwashers

Hi I have a LG dishwasher, model LD-2052WH/LD-2052SH/LD-2052MH. The machine is about 30 months old, and used very seldom. In the last two weeks we noticed a very loud "grinding" sound emmiting from the machine. This sound usually happens when you switch the machine on as the water if filling or the wash blades are rotating. What is the cause of this, and how can I get it fixed? Regards Paul Naidoo Ph: 0027 83 651 7558


... LG Dishwashers

Kitchenaid kudso1flss1 is stuck in clean mode. clean light flashing on and off. tried to reboot by unplugging, when i hit cancel it goes into "empty water left" mode, then goes back to "clean" light flashing on and off. Can't get it to go back to "start ready" position.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This is the first thing I'd try, based on your description. ( the clean light is an error code in this case ) On your control panel, If you press these buttons in sequence then close the door it ... KitchenAid Dishwashers

We did not get a install book with our new dishwasher. it is the she 45 mo model. need them badly, because it is different than our old machine. we bought the display model


Hi\015\012\015\012You can download the Bosch Dishwashers installation manual at this link. Just click on "Get this Manual"\015\012 ... Dishwashers

We bought a kitchenaid dishwasher that was a floor model. It did not have a users' manual with it. The Model # KUDL031VWH0. The Serial Number is #FW3001002. How can we get an owner's manual for this machine?


Try this site http://www.manualsonline.com/homepage/?src=04102010 ... KitchenAid Dishwashers

My bosch dishwasher wont dry. The model number is she44c02uc/47. I don't know what codes i need to see to get it to heat. I've tried to hold the cancel drain buttons in to change the code. I get a C1. what does that mean. Thanks for your help. john


... Bosch Dishwashers

The machine does not seem to rinse properly. We have checked the water fill level, water temperature, spray arms are not clogged, have determined it is not a hard water problem and have tried Glass Magic and CLR to verify the lattter. What else can we check to stop getting a film on everything in the machine? Plastics come out terrible, glasses and dishes foggy and sometimes still greasy. The model # is GU2700XTSY0 from the Whirlpool line of Quiet Partner 4. Any suggestions would help. Thanks!


Too much detergent; not rinsing well; hard water... There is an acid wash to revamp glasses/ you'd need to google it... ... Whirlpool GU2700XTSS / GU2700XTSY Built-in Dishwasher

The circuit board on our Miele G646 dishwasher has failed. do we 1) see if we can get another one second hand and in which case what other models have a compatible circuit board 2) try and get the board repaired and who do you recommend 3) bite the bullet and pay an exorbitant amount for a new board or 4) give up and just buy a new machine Thanks


What is the dwasher doing or not doing and how do you know it's the board. More information required please. ... Dishwashers

Have a lg model lds 5811st model dish washer for a little over 2 years and had the le error button .called technican replaced the motor now 4 weeks later the same error button.and the cancel button wont release the water standing in the bottom.also cant get repair man to garanty his work or parts.


Take off the door cover and you will find the wires melted into a black blown in insulation. Carefully free the wires and run a quick check to see if any of the wires are broken. If they are cut them and splice them back together. It takes a while ... LG LDF6810 Built-in Dishwasher

My Kitchenaid dishwasher (model KUDS02SRSS0) keeps burning out my dispenser. First I replaced the dispenser, then I replaced the control board and dispenser, it worked for two weeks and now I have a melted solenoid again in my dispenser. I've measured voltage to the solenoid and it is getting 110V through the entire diagnostic cycle. This is wrong. It should only get power at some point during the cycle to open the dispenser. It appears the control board has failed again and in the same wa


HI. The relay that controls the voltage and timed release command, via logic chip, is indeed damaged(stuck on). This is a common theme with this particular design. The original control board was recently replaced with a substitution model ... KitchenAid 24 in. KUDP01DLBS Free-standing Dishwasher

Frigidaire Model FDB780RCB0 I am getting water in the machine but it seems the arms are not turning what can I do to get that fixed?


The pump in the dishwasher is supposed to provide enough water pressure to turn the spray arms and make them rotate. The pump is faulty and not giving enough pressure or the arms are stuck.Try spinning the arms, if they rotate smoothly, you wil ... Frigidaire Dishwashers

Lock mode can't get the machine out of lock mode. Used the "normal/heated dry" sequence but won't release


TRY UNPLUGGING AND REPLAUG AFTER AFTER 12secs ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0988 seconds