Having problems with your Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher ?

SHE58C05UC/46 dishwasher won't complete cycle

\015 Gets about half way through full cycle then time resets to a higher number. Starts countdown again and gets to "1" and continues to run. opening door has soapy water. Does not matter what cycle is chosen. Has same behavior. Doing a cancel/drain does exit out of cycle.\015

Answers :

Repair Help & Product Troubleshooting for Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I own a Bosch dishwasher that has operated perfectly for about ten years. The model is: SHU9915UC. Now it wont complete the cycle. The undissolved detergent is all over the dishes. After running 4 more complete cycles without any detergent the same undissolved powder detergent remains on the dishes. I have also executed a cancel/drain cycle. The filters are not clogged. I am great at repairing many tools and automotive "stuff" and don't want to call a repair facility. Please help.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I just read your previous post and I wouldn`t replace that timer/control just yet. There is a way to visually inspect the control.\015\012\015\012 ... Bosch 24 in. SHU53 Built-in Dishwasher

Heller Dishwasher DWH16 has completed cycle and the door wont open. I put it on again wishful thinking and it still wont open. Can you please advise.


... Maytag Dishwashers

My bosch sgv53e13gb dishwasher wont complete a wash cycle


... Bosch 24 in. SGV53E03 Built-In Dishwasher

My dishwasher wont turn off. keeps cycling or begins a cycle anew once its completed


Defective timer motor.\015\012Replace the timer. ... Kenmore Dishwashers

I have a EuroTech dishwasher Model# EDW254E/SB. It was working fine but now it gives the Err code:er1 Its not letting incoming water in i know that. As well I have been told to try reducing the water pressure at the facet. Did that nothing.It drains but wont cycle to the next stage and let water in. I am presuming there is a valve of some sort not opening? And does the dishwasher have to be completly romoved to fix. Thanks


Hi and welcome to FixYa. I am Kelly. \015\012\015\012This is a water level sensing problem. Look inside your lower wash tub area and see if you either see a circular device off to one side or a finger like device sticking up about 2 inc ... Dishwashers

EDW5500DSS wont completely drain water Okay so now that my dishwasher runs, when it finishes a cycle it has a nice puddle of water at the bottom that never drains completely out. I am assuming its a relay or something because I looked for a floating switch (did not find), I can hear a pump sound as if it wants to pump the remaining water out, but, it doesn't. I really want to solve this problem soon so I can order the new door seal and needed part together. Checked the line out and of course i


The srainer over the pump could be clogged not letting the water drain quick enough. Be sure the screen is cleane out. I believe you would have already checked and cleaned this. I believe it is the impeller on the pump that pumps the water that is ei ... Dishwashers

WHIRLPOOL ADP 8540 dishwasher has blinking light on all the time (blinking in cycles of 4). When you turn it on (by holding the button down for around 4 seconds) it wont complete the cycle and you need to keep restarting it. can anyone let us know what the problem may be


See this step: ... Whirlpool Dishwashers

WHIRLPOOL ADP 8540 dishwasher has blinking light on all the time (blinking in cycles of 4). When you turn it on (by holding the button down for around 4 seconds) it wont complete the cycle and you need to keep restarting it. can anyone let us know what the problem may be. Thank you TD


WHIRLPOOL ADP 8540 dishwasher has blinking light on all the time (blinking in cycles of 4). When you turn it on (by holding the button down for around 4 seconds) it wont complete the cycle and you need to keep restarting it. can anyone let us k ... Whirlpool Dishwashers

Candy cfd612 dishwasher. wont complete cycle


... Candy 24 in. CD622 Free-standing Dishwasher

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

Dw009 e3 code wont complete cycle - Danby DDW496W Free-Standing Dishwasher


... Danby DDW496W Free-Standing Dishwasher

I have a linea dishwasher model LDW 3SS i think it is about 3 years old , it used to start but not complete the cycle just stop halfway and then would only work if you slammed the door or pushed front of machine and now it wont work at all ???


Even though this is an old issue, I thought it would be good to close out.\015\012\015\012I had the same issue where the dishwasher would stop at two certain point in the program. If I'd manually advance past that point, it would keep goi ... Dishwashers

My built in Frigidaire dishwasher model FDB126RBS2 wont drain to complete cycle


... Frigidaire 24 in. FDB126RB Built-in Dishwasher

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

The start stop button is flashing on my asko D 3250 dishwasher and it wont complete the cycle when i push this button.


... Asko 24 in. D3250 Built-in Dishwasher

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

I have a bosch dishwasher model # I believe is SHX4AP05UC it keeps tripping my braker in the middle of washing wont complete a cycle any suggestions?


Adam, in order to help you, you must provide me with more info. What size breaker is tripping. What does the maufactor's manual reads about what size circuit it must be plugged into. If your house is a little old you probably have a 10 amp breaker th ... Bosch Dishwashers

Wont drain Kenmore dishwasher is not draining ... standing water after the cycle completes


Hi,Here is a tip that I wrote that will help you with your dishwasher ... Kenmore 24 in. 15079 Built-in Dishwasher

I just purchased the Haier HDC1804TW/TB/TS countertop dishwasher today. I have it all hooked up but it won't run a complete cycle - all lights flash which the manual indicates excessive amount of water cycle not completed...allow dishwasher to complete full cycle...ummm...i'm not keeping it from doing so...help!


... Haier 17 in. HDT18PA Built-In Dishwasher

Kenmore Limited Edition Ultra Wash Dishwasher. Model 665 15892100, Ser. FL4910642 E71195, Stock #15892. Loaded dishwasher, started it, and went to store. When we came back, it appeared cycle had not completed (greasy and wet dishes) and the dry cycle had definitely not run. Bottom of dishwasher is filled with water. Tried to cancel/start the machine but control is completely blank and does not respond.


Hello,Welcome to FixYa.The issue with your dishwasher is more than likely the "thermal fuse" inside the control panel...it is all too common with those machines unfortunately.I've at ... Dishwashers

Danby countertop dishwasher model:ddw396w. doesnot drain between cycles or after completeing all the cycles. I cleaned the strainer, still doesn't work.should I put drain/clog clearing liquid in the dishwasher and complete one cycle?or any other tips?


Change the pump ... Danby 22 in. DDW396 Free-standing Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

Hi I have a Bosch sms 4012 dishwasher that was in our house when we bought it around 14yrs ago.It really has been an excellent appliance but for the past few months the control knobs have become 'sticky'and relatively hard to turn. Now the dishwasher is not completing the cycle properly by stopping intermittantly,taking almost double the cycle time to complete and not draining properly. Do you think this is just a blockage in the drainage system or something much more complex requiring a technic


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1991 seconds