Having problems with your Bosch Evolution 800 SHE98M05UC Stainless Steel Dishwasher ?

My Bosch SHE98M will not respond to pushing the Cleartouch buttons. It is just stuck displaying the normal wash. It will not respond to pressing any of the touchpads. When the door is closed it displays "not started". I have powered the unit down by switching it off at the supply, then restoring power but there is no change. It appears as if the cleartouch panel is no longer sensitive to touch?


Answers :

Repair Help & Product Troubleshooting for Bosch Evolution 800 SHE98M05UC Stainless Steel Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch SHE98M will not respond to pushing the Cleartouch buttons. It is just stuck displaying the normal wash. It will not respond to pressing any of the touchpads. When the door is closed it displays "not started". I have powered the unit down by switching it off at the supply, then restoring power but there is no change. It appears as if the cleartouch panel is no longer sensitive to touch?


... Bosch Evolution 800 SHE98M05UC Stainless Steel Dishwasher

Power washer - model jcb-pw20tss. TSS=total stop system. seems to be ''stuck'' on my model. Can you suggest method to free up and restore pressure which will allow me to switch on machine again. Mains electric =OK Fuse = OK Connected to water supply =OK


... Pressure Washers

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

Wont restart after power surge & verifying power supply restored


The control board may have been damaged by the power surge. You should install a surge protection device on the incoming power line, thereby protecting everything in the home from damage.\015\012\015\012If you need help with this, go to t ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

An electrician switched off the power whilst doing other work. Power was restored OK. But when we came to use the dishwasher there appeared to be no power to it i.e the control panel remained blank. We have checked the fuse box and all appears to be in order.The appliance is a Siemens FD 8909 dishwasher


Maibe the internal fuse of the dishwasher blow for a spike, check first if you have power at the socket if so is highly posible that you have a blown fuse in the dishwasher ... Siemens Dishwashers

Model G2582 SCVi We have F70 fault displayed. Have turned off water supply but drain pump continues to run even with machine supposedly switched off. Is there a way to stop as it will take 3-4 days to get a service engineer here. Note can't simply throw a switch in fuse box as this also takes out multiple other power ponts


... Dishwashers

I have a Maytag Jet DWU9902AAB. We had a power outage and when power was restored the dry light was on and I can't get it to clear or do anything. I have tried turning the breaker switch of then on, but still nothing. Any ideas??


... Maytag Dishwashers

On my Kenmore Ultra Wash Dishwasher model 665 the Normal Wash light is blinking even though the previous cycle finished successfully. Also I can't start the dishwasher -- it doesn't respond to any of the buttons. I have powered it off and on and the Normal Wash light comes back on within 5 seconds of restoring power.


Http://appliancejunk.com/forums/index.php?topic=2933.0\015\012\015\012\015\012\015\012Hi. please find above your service and repair manual, bel ... Dishwashers

I have power to the unit but there are no lights on door when closed. Unit will not respond to any buttons and lock not on.I have opened up the door panel and have power to the door switch and then to the board.What is my next thing to check?


Ok so you have power going to the unit at the bottom if the unit is not under warranty? first are any LEDs operating at all when door is opened? if not you most likely have a control issue to test this you would remove the screws along both sides of ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Good day after the power is turned on to my brand new kudc03fvss dishwasher, nothing happens. have made sure that the power supply is ok and that the door is properly closed. there is 115 volts at the circuit board inside but nothing happens. no lights, no response to switch etc. just dead. need some advice


You said your getting 115 volts and that is across the power wire and its neutral not a power and ground.. i had a case like this last week and when i got there the unit had power if tested from black to ground but not from black and the white neutra ... Dishwashers

My Siemens L34A dishwasher will not respond to turning the power on and off, nor any dihswashing settings. It appears to be 'frozen' with the lights on the control panel permanently on, I have tried to reset it by turning it off at the breaker switch, but with no luck.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Check continuity to the door switch if that appears to be fine\015\012then it is the control ... Siemens 24 in. SL34A006UC Built-in Dishwasher

The dish washer ran its full cycle but won't shut off. the little pump motor in the very bottom keeps cycling water in the bottom. it won't shut off when you open the door, it won't shut off when you push the power button and the front switches won't respond. the little light on the front of the dish washer is blinking and it has never done that befor normally the lites are always on solid.....


The drain stuck cycle ( I presume you mean drain pump running constantly ) are directly related with overfill scenarios for Asko dishwashers of this ... Asko D3122XL 24 in Builtin Dishwasher

Indesit dishwasher idf125 door will not click shut. This has happened before. Have tried cleaning filter etc. Low salt indicator light is on. I do not think we need to put salt in as we are in a soft water area {scotland} Have tried switching off power supply and leaving it for a while. It is only about 2 years old


... Indesit Dishwashers

Dear sir In an attempt to dislodge a blockage of my sewer line using Draino and a plunger some of the Drano ended up in the dishwasher and now the dishwasher will not run. My dishwasher is a SHU3036UC/U12. When starting the unit up it empties the unit but the cycle newer ends, in other words the timer does not advance to the next cycle, I have determined that the timer motor works by removing it from the unit and supplying it with power. One thought is, can the water level switch be stuck in


HiCheck this video and clean the drain pump assembly: ... Bosch SHU3036UC Dishwasher

Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?


Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher

My Kenmore ULTRA WASH dishwasher model #1603* does not respond to any command. When I select a desired washing I only get a blinking light on my selection and nothing else. If I select ''Cancel/Drain'' it blinks as well. I receive no response at all if I select ''Start/Resume''. To stop the blinking I must turn off the circuit breaker. When I restore the power, the control board is not lit, however, selecting any of the wash cycles and the blinking starts once again. The manual refers to a blink


Replace timer/program module\015\012Vitally ... Kenmore Dishwashers

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

My dishwasher tripps out when it is plugged in, how can it be resolved? ----- when i plug the dishwasher into the socket, it cuts the power supply to some electrical points around the house. It trips out a switch in the electrical terminal box, what can i do about this?


There is a shorted component in the dishwasher that must be found and repaired. Requires hands on troubleshooting.Eric ... Dishwashers

Hi I have a bosch SGV4313 dishwasher. The operating switches on the top inside of the door do not light up and do not appear to have power supply to operate. Anybody any ideas


... Bosch Dishwashers

ASKO dishwasher D3122 drain pump wont stop pumping and the machine wont respond when we press any of the program or start/stop buttons. the program light is flashing. We can turn the power off with the main switch on top of the door but when turning it back on the pump starts pumping again. please tell me how to fix this problem so we can get it up and running again.


... Asko D3122XLSS Stainless Steel Dishwasher

Karcher B402 pressure washer Motor runs as soon as power supply connected, on/off switch does not seem to make a difference and no pressure at outlet? Was working fine, stopped for half an hour, came back and wouldn't work. Thanks Bob


Bob I had this happen to my Karcher, the pressure seals have blown. $Au200 for service and replacement from karcher dealer. tyhey would not sell the parts for a DFY ... Pressure Washers

My Kenmore 665.15962990 has just quit working. There is water in the bottom that did not drain. The panel is just dead, none of the digital spaces will respond to touch. The stock #15962. There is power to the unit. The door switches check out OK. What should I check next and how?


You have a blown thermal fuse. You can change this by unscrewing the the inner door from the outer door and changing the fuse part#3376359 here is a picture to help you see how to open the unit up.\015\012 ... Kenmore Dishwashers

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch Comments: Aug 22, 2009 - I tested the door swich and I have power on both poles when it is closed. there is 2 switches on the latch but the one with power to it powers up the circ


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0896 seconds