Having problems with your Bosch Integra 500 SHX45M0 Built-in Dishwasher ?

Bosch Dishwasher SHX45M I have cancelled cycle and reset but pump will not shut off. how do i reset complete control panel


Answers :

Repair Help & Product Troubleshooting for Bosch Integra 500 SHX45M0 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch Dishwasher SHX45M I have cancelled cycle and reset but pump will not shut off. how do i reset complete control panel


... Bosch Integra 500 SHX45M0 Built-in Dishwasher

Dishwasher front panel lights are all blinking in unison. Pump has removed all water from bottom including sump. Pump and lights will not shut off or reset with dishwasher door closed or OPEN. I have shut the circuit breaker off to keep from burning up the pump. Problem continues if I reset circuit breaker.


It would help to know what the make and model of the dishwasher is.\015\012\015\012Most likely the flood switch at the base has been activated. ... Dishwashers

Leak from a De Dietrich Integrated Dishwasher has caused 3 red lights on the left of the Control Panel to flash and also a Blue Light on the right hand side of the Control Panel to flash. On resetting the Appliance Controls, the machine starts pumping out and then closes down, with the Control Panel lights flashing again. Help


Pull the built in unit out and tilt towards the rear right leg and the water will drain on to the floor. The Dishwasher then restarts but the anti flood sensor will reactivate after 2-3 more washes. Do not know final fix yet. ... De Dietrich Dishwashers

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

I have a KitchenAid dishwasher model KUDC10IXWH1 that has no control power. I have already verified that there is 120V at the control board. The unit kept the lights on after the cleaning cycle was done and I couldn't shut them off. I reset the electrical breaker and now nothing works, but the board has power. Please give any advice you might have. I was thinking of replacing the board, but I'm not sure if it is the board or the front control panel. Any way to tell?


... KitchenAid 24-in Built-In Dishwasher White ENERGY STAR KUDC10IXWH

I have a GE monogram zbd5900 that continues to drain, won't shut off. The drain pump just runs. None of the lights on the control panel will come on, tried pressing and holding buttons to clear, nothing. Turned off and on circuit breaker (even left it off overnight) and did not change. Drain is not blocked, pulled the unit out and put water in the bottom and it pumped the water out just fine. any thoughts?


See if you can access the tech sheet, should be on the right side of the underside of the unit after you remove the toe panel, or perhaps in the console. Almost sounds like a stuck key pad but the tech sheet might shed more information on this malf ... Dishwashers

Dishwasher problem Hi We have a Whirlpool GU 2300, the machine has stopped and is the clean LED on the control panel is showing a 7 pulse sequence which I guess is a fault alarm. I have tried resetting, checked the door switch and looked at the pressure sensor at the drain pump outlet. I changed the heating element and fitted an uprated control card earlier this year. Any ideas?


I solved the reset by pressing the air dry and reset buttons 6 times in sequence, the whole panel array lit and I was then able to reset. I have had no problems since and have used it 6 times. I initially thought that the chipset had a volatile memor ... Dishwashers

I have a 13 month old Bosch SHE58c dishwasher. The pump runs constantly and will not refill the tank. There are no error codes thrown on the control panel, but not sure there are error codes for this model - the manual doesn't mention any. So I have removed the side panel and can see the bottom pan is bone dry and I made sure the overflow drain switch was not bound and operates freely. Is there some type of reset button or other task I can perform to continue troubleshooting this problem? Repair


I have exactly the same problem. Turn on the machine and it just pumps and pumps, door controls do nothing. According to the technician who came and looked at it the problem is a bad control board. He ordered the part and we are waiting on it. ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have a pldb998cc0 frigidaire. The tech who came out told me the problem was the control panel and that they don't make them anymore. There is not apparent arc marks so it did not short out. We have turned it on and off to try to get it to reset and all that happens is the front panel lights all go on for 5 seconds then die out. There is no sound at all of pump or water. I talked to the manufacturer and they do not manufacture this part anymore. Any suggestions before I have to pitch it and go


As much as i love what i do i see so many bad techs this guy lied simple! the least he should have done was try another board if he was sure that was the fault he would have its simple electronics fault finding he must have at very least tested the b ... Frigidaire 24 in. PLDB999S Stainless Steel Built-in Dishwasher

I have a Diplomat ADP8242 Dishwasher that continues to run during its wash cycle. The machine starts and heats up correctly but will not switch to its rinse cycle and just keeps running with 2 intermitent beeps. I have tried to reset the programe which does pump the water out and resets the control panel, but unfortunatly does not clear the fault. Can you help?


... Dishwashers

I have an Asko 1585 dishwasher. It drops the inlet valve on step (step 12), and the recirculation pump (next step) tries to pump with no water. Later at about step 47, the inlet valve begins to work again and the dishwasher finishes the cycle without a problem. I have had the board checked, and all of the power supply and transfer circuits are good. That leaves the processor. Is there any combination of buttons to press which can completely reset the controller board?


... Asko 24 in. 1585 Built-in Dishwasher

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

Bosch shy66c drain motor keeps running after wash cycle is complete, can't reset using control panel or circuit breaker , pull dishwasher out and tilt it 45 degrees, there is same water on the flo


... Bosch 24 in. SHY66C05 Stainless Steel Built-in Dishwasher

I have a GE Quiet Power 3 that has completly died. I cannot get a light to come on or anything to beep when pressing buttons. I checked the circuit breaker and outlet and they are both working fine. I tried pressing and holding the reset button on the front control panel and nothing. It seems to have just died at 2 years old. Anyone have a solution? GE wants $80 just to look at it.


A dead set simply means a cut off of power supply. Open the back cover of your dishwasher . Locate the area where the AC cord is located and look for the plastic fuse holder which is usually installed in one of the AC cord line open it and replace t ... Dishwashers

The dishwasher does not pump all of the water out. There is an inch or two left in the bottom of the dishwasher after the cycle has completely run. The control panel has been recently replaced on this dishwasher and it did not correct the problem. Help?


You likely have a dirty or faulty water level sensor in the machine that needs to be cleaned or replaced. ... Dishwashers

Cycle interupted until pressure applied to door, near control panel. Fault is intermittent. Sometimes I need to lean a chair against it to keep it going. Door clicks shut nicely and does not leak. Cycle always starts but often will not complete without a thump. Is pressure inside bowing the door and activating a safety switch?


Problem on the safety switch\015\0121)try to adjust the safety switch to contact properly with the door.\015\0122)any screw is there on switch means loosen the screw &adjust to contact with door. ... Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher

SMEG STX dishwasher does not complete the wash cycle, stopping after 3 minutes on all cycles displaying error code E1. The machine seems to start with the usual whirring noise but then stops after 3 minutes without pumping in water. The machine is a few years old now but has needed 2 new control panels already although this does not appear to be the problem this time. Any suggestions? Thanks DW


... Dishwashers

Hi, ^The GE dishwasher (PDW788000SS) will not fill in either "rinse only" or "normal wash" modes. The control panel lights up with all functions. After selecting rinse only or normal wash and pressing/holding the start/reset button down for several seconds to reset the unit the drain pump comes on for approx 90 seconds as advertised. Checked the float switch and there is no continuity in any position of the little switch arm and the switch arm has no spring on it. Seems like this is a faile


Hello there:If there's no water entering your dishwasher in these cycles as you described, check these:\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 ... GE 24 in. Profile PDW7880G Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

I have a bosch she5al06uc/05 and it seems to run for a long period of time. I end up manually shutting it down. It doesn't make any sound indicating that the cycle is done and I have tried resetting it to the default settings with no success. I'm not sure wat exactly is suppose to be flashing wen in the control panel either. any help would be appreciated.


Hello,Welcome to FixYa.Based on your description I'd say the issue is with the control...unfortunate ... Bosch SHE5AL06UC 24 in Builtin Dishwasher

My whirlpool DU930PWSQO dishwasher won't start. Drain will work, other control panel lights work . Tried shutting power off/on and the heat dry - normal reset sequence but that didn't work. Any ideas?


... Dishwashers

I have a Maytag quiet series 300, model # MDBTT60AWW. The front control panel have some green lights on but the start/cancel button won't work. The dishwasher will work for 5 days and quit for 2-3 days then work again. I tried to reset the main electrical panel hoping the dishwasher will reset too but it didn't work. I opened the panel on the front door to see if water is getting into the electronic panel but it is dry. I'm wondering if it is the front control panel itself is the problem. I want


... Maytag Dishwashers

Kitchen Aid Dishwasher model # KUDK03CTSS3 The control panel lights are blinking rapidly, several of them. Nothing works, even after powering off and on again. I see there are instructions to reset the control panel on these before calling for service. How do I reset the panel on this model?


... Dishwashers

PLD2560LCC1 Frigidaire Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1273 seconds