Having problems with your Bosch Integra® 500 SHX46A0 Dishwasher ?

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


Answers :

From your description, I doubt that the problem is door latch is the cause.\015\012
\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing to the next cycle (inlet water) and because the pump runs even when the door is open, I agree that the controller card may have failed.\015\012
\015\012If possible, inspect all the wire connections (remove main power before you do this) ... if there is a loose connection, the controller could do odd things.\015\012
\015\012Good Luck!  Please report back what you find, OK?
Repair Help & Product Troubleshooting for Bosch Integra® 500 SHX46A0 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

My 501HT has stopped draining. It runs through a couple of cycles until the water inside builds up enough to leak out through the door. I have tested the cam switches #3 and #4 and they are opening and closing as the cam turns. How do I test the drain S/V and how do i know if the pump is reversing?


Hello Dabean\015\012Have you sort out your problem yet if not please email me your problems and I try to sort them out for you my email address [email protected] God Bless hav ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Bosch SHX43M05UC Dishwasher. To wash, you select the cycle and then close the door to start the wash. Now when I push the on button, the pump turns on. I can't tell if it's pumping water or not but it's not supposed to start until the door is closed.


... Bosch SHX43M05UC Built-in Dishwasher

Have a Bosch shy56a05uc dishwasher that suddenly stopped working to a point. I believe it is related to the door latch switch, because I don't feel the door securely latch shut when I close it, and I also don't get any cycle lights or times registered on the LED readout. If I depress the on switch, the drain pump will start even with the door open, and, depending on how long I leave the switch on, water will start to fill in the dishwasher, open or not.


Does your dishwasher electronic control or mechanical timer? if mechanical timer, I encounter a similar problem n change the mechanical timer. that problem solved.\015\012\015\012Prince P ... Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

Good morning, I have a F&P dishdrawer ds605i (i think!) single drawer intergrated front. I dont know whats happened to it. The last cycle it decided not to empty the water out, so i manually emptied it. Now it seems stuck. All it does is run the fan. i can't start a new cycle. The start/pause button allows me to open and close the door as normal and i can hear the lid opening and closing.......... I have tried turning it off for a day at the wall switch. I have also noticed i can


Hi \015\012I guess the model no. you have sent is not correct,however given bellow are links from where you can troubleshoot your problem to your dishwasher which is related to your issue:-\015\012 ... Dishwashers

Pump starts as soon as main switch is turned on, even with door open. Also does not even try to fill. Does count down if you close the door and let it run but no water so no effect. I am guessing control board or anti-flood? Thanks


Is your door switch defective,that will cause same symptoms ... Bosch 24 in. SGV57T03GB Built-In Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Machine cannot finish cycle and is stuck in pumping out mode. Only tiny amount of water in drain basin at bottom, no excessive water. Was set at 10pm, still attempting to drain 8am! Has no diagnostic dials or manual over rides so continues on whether door is open or closed, even if I switch off and on again. Possible related issue, recently finish at end of washes has been "grainy", far from perfect, surfaces slightly sandy feeling.


... Bosch 24 in. SGV43A03 Built-In Dishwasher

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Dishwasher model: se6 tie1 Fitted under kitchen work-top. Problem: After setting a program & switching on & closing door ? there is a normal sound from within but if door is opened there is no evidence of water being pumped in. I previously cleared food debris from the drainage pump area (including under the pump cover), checked the spray arms and checked the water supply was getting as far as the long in-take pipe. As it seems problematic to remove the (screwed in) dishwasher, I have not che


... Dishwashers

My Bosch SHY56A02 dishwasher won't fill....When cycle is started, it seems to pump water out but none in. Water feed is good....Added water manually and it pumps out immediately. Also, unit continues to run with door open...door switch is not jumpered. Could it be the fill valve? More likely the control module? Thanks for your help!


Hi,\015\012\015\012As water is filling in your dishwasher a float rises along with it. When the float reaches a predetermined level it shuts off the flow of water by activating a switch thereby preventing a leak. Sometimes the float can g ... Bosch Dishwashers

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

I have a Bosch Exxcel dishwasher which runs the drain pump constantly even with the door open and despite there being now water in the machine at the cycle wont start. I have checked the warer amtrix and the ffed hose to the sump for blockages. The float switch operates OK but when the water drains down the float drops and the water is pumped in, then the float rises and water leaks out and the drain pump kicks in again and no more ater will come in unless you push the float down. Inside the bas


I am not sure about this model but most models run a drain cycle for a set period at the start of a wash cycle and then move on to normal filling and cycle of machine provided the various switches are at the low level it will carry on to its set cycl ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Bosch Dishwasher SHV4313GB/17 Wont switch off ! The machine keeps running even when you open the door The pump is trying to drain water away (even though there is no water left in machine ) Have tried to reset it as instructed but to no avail. It has beeped like it has finished cycle but the pump wont switch off HELP PLEASE !


Introduction: This may work for your problem, but only if you're finding that you cannot get further water to flow into your machine. If your machine fills OK, then this ISN'T a solution to your problem. If your machine doesn't fill but your drain m ... Dishwashers

Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.


If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1777 seconds