Having problems with your Bosch Roto-Power Lance for AQUATAK 1250 ?

The foam only works for a couple of seconds ?


Answers :

Repair Help & Product Troubleshooting for Bosch Roto-Power Lance for AQUATAK 1250

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The foam only works for a couple of seconds ?


... Bosch Roto-Power Lance for AQUATAK 1250

I own the Siemans SL34A006UC dishwasher which had the recall repair completed. Now it doesn't work right. The unit goes through any of the cleaning choices but when it comes time to drain, the unit stops for a few seconds, swishes water for a couple seconds, stops again, then swishes for a couple seconds, stops and then goes back in to regular cleaning mode until the timer reaches zero. At each drain cycle, it does the same thing earlier mentioned 3 times in a row, then back to washing. The unit


You say "dishwasher which had the recall repair completed." (sic) "Now it doesn't work right" (sic)\015\012\015\012Being a professional I must advise,and that, if this is the case, th ... Dishwashers

My karcher G2000QT WORKS AT HIGH PRESURE FOR A COUPLE OF SECONDS AND THEN STOPS THEN A COUPLE OF SECONDS LATER WILL START AGAIN WHATS GOING ON?


Sounds like a blocked lance jet to me. remove lance jet, clean it . run machine watch for steady streeam of water, if not a steady stream of water, it could be pulling in air on the suction, or its bleeding air from the inlet pipe.hope th ... Karcher 2500 PSI Pressure Washer

My Kitchenaid ModelKUDI01TJBL0 only leaks at initial start up. Just after the water fills, the first few seconds of the wash cycle. It pours out the front door for a couple seconds than no more for the rest of the wash. It is level, no cracked arms, or loose pumps.Splash guard is in place. The float seems to be working, not too much water in the bottom. I am stumped. Although I do feel that it has something to do with the level of the water being too high, when the arm starts turning, it makes a


Is the unit level or leaning back if leaning back it is morelikey filling too much if level make sure the float moves up/down easy if not clean ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

I have a Whirlpool model DU1055KJVQ1, Type 575-0 under-counter dishwasher which is less than 2 years old. In the last couple of weeks, it wouldn't start intermittently, and I would need to hit cancel on the keypad, and then restart. Now that doesn't work. When I try and start the dishwasher, it doesn't work. I press Normal for the cycle, heated dry for the Option, and then hit Start. The buttons light up for 20 seconds or so, nothing happens and then they go out. Any ideas?


... Whirlpool Dishwashers

I have a Lifestyler Expanse 1500, Model #831.297330 that was in water in a hurricane. After months of letting it dry out, I tried to use it. It would be fine for a couple of minutes, then go as fast as it could, then go to Error. Now it just goes a couple of seconds, then goes to Error. I traced the motherboard with a pencil eraser and sprayed it with electronics spray. Nothing works.


... RTO Dishwashers

I'm trying to get a Durabuilt pressure washer (model DB1303) to work. After hooking up the water hoses I plug it in and turn on the power. It sounds like it's running but there is no increase in pressure and it runs continuously. I only let it run for about 10 seconds and then turned it off. I tried it a couple of times...no luck.


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

I recently bought a second hand karcher 205 it worked fine for the first couple of times then suddenly started leaking water


... Karcher Pressure Washers

My De Dietrich dishwasher turns on but then turns off after a couple of minutes with no water entering dishwasher. I found some instructions and turned on and off 5 times (and unplugged). This worked once and full cycle ran but not the second time. Not sure if it is worth paying 165 call out charge or getting new machine as 7 years old


... De Dietrich 23 in. DVF110J Built-in Dishwasher

When i turn the dial to start the dishwasher, it buzzes for a couple seconds and then nothing. I saw some water on top of the dishes, and the heating element is working as it hissed when i splashed water on it. I tried different settings, and still the one buzz sound and nothing


The busses the nothng is the motor . but it should have filled with water so ck the float in the front cornnor ( just lift it up not too far and let it down . so this a couple of times and see if waater will come in ... Kenmore 18 in. 14432 / 14439 Built-in Dishwasher

Hi Bought karcher k5.80 some time ago It didnt work well and I put it away however got it out again its blasts then trickles water on for couple of seconds the off again. What if anything can I do?


I got the same problem as msellar1. Anyone got any ideas to resolve??? [email protected] \015\012Thanks.\015\012Basically, turning the spray nozzle to r ... Karcher Pressure Washers

My karcher 3.550 pump not working after pulsing for a couple of seconds


... Karcher Pressure Washers

The hidden control panel has only about half the lights showing what function is pressed. A couple of days ago the washer would not start. The only function which would work was the far left sensor light. After trying to cut power and pushing other buttons, to no avail, we let the machine sit a couple days. It now works again with only half the lights on function pad working. It acts like there was a electrical short.


First retrieve the tech spec sheet behind the toe-kick panel located near the floor and run the diagnostics if it will let you do so w/o the full operation of the keys on the pad,then if it wont the touchpad or keyboard on the front that you use to s ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

Hotpoint df32 my df32 stops working during its water intake The water intakes come in 3 10 to 20 second pumpings.Its always after the second .spurt that it stops. In order to start it working again,sometimes a quick on/off of the main jkitchen water tap will start it, otherwise I have to advance the timer manually


REPLACE WATER INLET SOLENOID ON WASHER ... Hotpoint 24 in. DWF32P Free-standing Dishwasher

Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr


WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers

My dishwasher is working well but makes an intermittent whistling noise, 10 seconds 'on', 10 seconds 'off'. The machine is 2 years old and runs on water from a softening unit (less than 0.7 moles/litre). None of the manual's suggestions has worked. How can I stop this noise? Thanks, Jim.


This is caused by a partially blocked valve or inlet, it is a little blocked, and this sound you hear is the air pushed through it making a sound. You need to clean out the inlet valves. \012\012\012 ... AEG 24 in. Favorit 80860iW Built-in Dishwasher

Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely. the oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any. I will


There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing. Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. It is v ... Dewalt DPH3100 Gas Pressure Washer

Pdw 9200 jo3ww dishwasher- The start button doesn't work. The arrow keys work and the heated dry button works. I tried turning the power off for 30 seconds and it still doesn't work any ideas?


... GE PDW9200N Built-in Dishwasher

Greetings! My Bosch SHE3305UC/UC12 has worked faithfully until last week when we had to pull it out of its home to retile the floor. Upon reconnecting all of the connections, it no longer works properly. The initial drain cycle works, so the flood switch is fine. But after draining, it just quietly hums. The test cycle actually seems to move to the next step for about 30 seconds, before also just humming. I'm thinking I need to check the valve, but not sure how to do it on this mod


Hi\015\012\015\012The hum sound indicates a bad motor and it should be\015\012replaced. Hope this helps...please post back for further assistance.\015\012\015\012Daniel ... Dishwashers

Hi there I've got a Miele G572 dishwasher that works perfectly, except that it trips the circuit breaker when it tries to fill with water. The heating works, the timer advances, the spary arms rotate and it drains well. It is a second-hand unit that worked for about 3/4 of the first cycle, then it tripped the earth leakage detector. Cheers John


If it it is tripping the circuit breaker when filling , then the problem is localized to following parts:Inlet Valve.Wiring Harness to Inlet Valve.Water Level switch.Timer control Board.Afte ... Miele G2670SCSF Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

Hello, Our kitchenaid DW has stopped working. Non of the buttons cause a any of the lights to turn on. Of course, it will not start. On its last working cycle, it had a very strange washing cycle. It almost sounds like the water was not splashing around (even though I opened it while it was working and noticed water at the bottom). I checked the circuit breaker, and it is not tripped. For a couple of weeks, the DW had started making a kind of metallic noise while in the washing cycle. Also,


It is nice to see a problem described with such a depth of observations. It helps in closing on to the possible causes of the problem.\015\012\015\012For the moment let us make sure there are no remnants of the glass left in the dishwashe ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hello, my Bosch Classixx dishwasher SGS43E42EU/21 has me stumped. It starts by taking in water but when "filled" pumps out for a couple of seconds then refills for say 10 seconds more before another 2 or 3 seconds of pumping out. This cycle continues for ages without starting to wash. I've tried various things: - checked the Auto Stop valve isn't being activated by leakage (removing the polystyrene float and bottom tray makes no difference - there's no leak) - the valve seems to operate it


Hello Dave,\015\012\015\012Sounds like an overfill problem - the symptoms are consistent with a failed pressure switch. Water enters the dishwasher through a chamber which has a float arm connected to a small microswitch -this is the pres ... Bosch Dishwashers

We have an AM-14 dishwasher. It now will not work on auto. It would sometimes and then not and now only on manual. We have had a couple people in to look at it. One says the main board was bad, so it was replaced and the problem continues. The board that was removed was put into another washer and it worked ok. We were told then that that a wire from the motor was wrong and thats when we called in another person. That person said the board was bad and they couldn't work on it. We are in Lancaste


... Hobart AM14-253 Free-standing Dishwasher

Unit shuts off on first try, always works the second time.


Dear Sir:you have 2 options:1) The board can be faulty, tight any connector, loose wire, break, or burn. see if some component is heated. 2) The start button can be dirty , or stuck, clean with special spray contact cleaner.3) Test th ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0967 seconds