Having problems with your Bosch SGE63E05UC 24 in Builtin Dishwasher ?

I have a Bosch SGE63E05UC dishwasher that keeps intermittently showing an "E:25" error code. Occasionally it will get all the way through a cycle without going into error, but more often than not it will error and stop. So far the main control module in the front panel and drain pump have been replaced and the problem persists. All hoses have been checked and are clean (unit is only 1 year old) and drains well, when it does drain. Any suggestions?


Answers :

Repair Help & Product Troubleshooting for Bosch SGE63E05UC 24 in Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosch SGE63E05UC dishwasher that keeps intermittently showing an "E:25" error code. Occasionally it will get all the way through a cycle without going into error, but more often than not it will error and stop. So far the main control module in the front panel and drain pump have been replaced and the problem persists. All hoses have been checked and are clean (unit is only 1 year old) and drains well, when it does drain. Any suggestions?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

We have a GE profile dishwasher that will not drain. We have replaced the keypad control and control module and it still will not drain. When we put it in service mode, we can get it to drain that way but when it is taken out of service mode, it goes right back to the same problem.


Its the timer issue:--\015\012what the timer does is control the motor and drain valve. If the timer doesn't work properly, the water may not drain and you need to replace the timer. This problem is common. ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Electrolux EIDW6305GS1 will not run , keeps flashing error code 11 which indicates drain valve problem. I have replaced drain valve, wash pump, float valve and reed switch but no luck, still flashing error code 11


... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Bosch dishwasher shu5300. Replaced control panel. Then replaced drain pump. Will not drain water. Can hear drain pump kick I and drain water for 2 to 3 seconds then stops


Have you checked the water is one, can you hear buzzing from the inlet valve, likes it's calling for water but not getting any?? ... Bosch 24 in. SHU53 Built-in Dishwasher

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

I have a 13 month old Bosch SHE58c dishwasher. The pump runs constantly and will not refill the tank. There are no error codes thrown on the control panel, but not sure there are error codes for this model - the manual doesn't mention any. So I have removed the side panel and can see the bottom pan is bone dry and I made sure the overflow drain switch was not bound and operates freely. Is there some type of reset button or other task I can perform to continue troubleshooting this problem? Repair


I have exactly the same problem. Turn on the machine and it just pumps and pumps, door controls do nothing. According to the technician who came and looked at it the problem is a bad control board. He ordered the part and we are waiting on it. ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Asko d1976 soap dispenser doesn't open/deliver soap during the cycle - no error codes/water pumps & drains ok Do I need to replace the module or is there a wax motor that needs replacement? Is there a service/repair manual out there for askos? I also have an asko washer (6021) & dryer (T721) so having a service manual would be handy!


... Asko D1976 Built-in Dishwasher

Electrolux EIDW6305GS1 will not run , keeps flashing error code 11 which indicates drain valve problem. I have replaced drain valve, wash pump, float valve and reed switch but no luck, still flashin


Success....Error 11 on Electrolux dishwasher?\012 I have an Electrolux EWDW 6505 which in the start of a wash cycle would start beeping and Error code 11 would display.\012 The problem: Drain Valve (Small copper lever switch inside)\01 ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Our GE model GSD4320Z00B is having a problem with the drain system. I've run the unit in the test mode and it does pump the dishwasher down. The problem is the unit does NOT pump down during a normal wash cycle. The fact that the unit works in test tells me it is not the pump. I've checked all the hoses and drain paths and there are no obstructions, again verified by the fact it works in test mode. Any test that can be used to determine the problem besides replacing parts one by one?


... GE 24 in. GSD4320Z Built-in Dishwasher

I have been interacting with Daniel about my Dishwasher Smart Dispenser problem. The last thing he had to say to me was that I needed to replace my drain pump. Before doing this, I would like an explanation of why a new drain pump will solve my problem since my dishwasher is draining just fine...it is my Smart DIspenser that is clogged up and not working ?? See the discussion here: Dear go4t9ers, There is a new Comment for the I would like to run the Smart Dispenser Purge Solution on


Ok first this is the schematic for your entire machine http://www.s ... Dishwashers

My Whirlpool wdf530payw dishwasher is not draining. I ran the service diagnostics using the control panel, and the code that came back was Function code 8, and Error code 2 "Drain Motor Electrical Problem". The possible causes listed are: a. Loose Connection in drain motor circuit, and/or open drain motor winding. b. Open Fuse on control to drain motor c. Faulty drain motor drive circuit on the control When I hit the "Cancel/Drain" button there's an faint buzzing sound for about 2 minut


... Whirlpool Dishwasher. Front Control Dishwasher in White WDF530PAYW

I have a Jenn-Air JDB9910AWB dishwasher. The problem I am having is everything seems to work fine until the drain cycle. It sounds like the pump is frozen. After selecting the drain button you can hear a click in the control panel followed by a 1-2 second growl in the pump but it doesn't turn or pump. I am assuming the pump runs in reverse for draining? Is it safe to assume the pump is bad?


... Jenn-Air JDB9910 Dishwasher

I get an LE error message on my LG Dishwasher. I replaced the pump. Still get the LE error. Replaced the main control. Still get the LE. No blockage in the pump. What now?


When you receive the LE error code, unplug the machine for approximately 15 - 20 minutes. This will reset the microprocessor.Oversudsing is the main cause of LE error codes. Using non-HE detergents or too much detergent will cause stress ... Dishwashers

HE error My LG LD-14aw1 is showing HE error code - Heater Circuit is troubled???. (Not as much as owner!!!). I have repaired several dry solder joints in the control module, which have been causing various operating failures, but the HE problem has got me stumped. Can anyone provide me with a wiring diagram of the machine and or the control module? I'd like to trace the heater circuit to see if I can find the fault. Many thanks


From the manual: Errors: HE: Heater circuit failure.Please call your Authorized Service Center or LGECustomer Service at 1-800-243-0000(US), 1-888-542-2623(Canada). ... LG 24 in. LD-12BW5 Free-standing Dishwasher

My Bosch SHX46A06UC/42 stopped working today. I can hear the drain pump constantly pulsing about once every second. I checked the control board and found a relay contacted burned. I re-soldered the relay so it now has a good connection, however the drain pump still just pulses. How do I verify if the drain pump is bad or if the relay failed, or yet another problem?


... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

Hi. I have a 3 year old LG dishwasher. It will not drain. Display shows OE. I completely cleaned the drain assembly inside the DW. I checked the discharge line, it is completely clean. I disconnected the drain line from the air vent assembly at the sink and ran the DW, still will not drain. I disconnected the discharge pump wires and ran current directly, the pump works. I replaced the main control PCB, still will not drain. Please advise. Thanks


Measure the electric resistance of the Drain Motor. (Value should be 20-40 Ohms) If it is out of spec, replace it.\015\012\015\012Please reply with what worked best. Thanks! ... LG 24 in. LDF 7811 Built-in Dishwasher

Have GE Dishwasher model GLD6700N20WW,unit has stopped draining! Took apart and pump was running when check, but no water coming out. Checked drain line and pulled apart pump housing, all clear. Thought maybe pump has a silinoid built inside of it and was stuck shut, so bought new pump and same thing, no water will go thru! Please help me? Is it control module, or turbitity sensor possibly?


... GE Profile PDW8600J Built-in Dishwasher

When I replaced my garbage disposal I forgot to remove the knockout tab that would have allowed my my bosch SHE58C05UC dishwasher to drain into the disposal. I discovered my error the first time I ran my dishwasher and discovered that none of the water had drained. I then removed the knockput plug and reattached the drain line. My dishwasher now drains correctly but makes a loud sound whenever the pump turns on. Have I ruined my pump or is there something I can do to eliminate the loud noisy pum


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thank You for using\015\012FixYa. To start with check the pump and try to clean it out, then check drain\015\012hose for any obstructio ... Bosch Dishwashers

Our Asko D3112 was not draining, so we had maintenance drain the hoses to clear any blockage but it did nothing. They said it must be our pump not working. I ran one more cycle to see if things went back to normal, however now our pump won't shut off. We have to unplug the machine just to get the pump to stop. We had a repair technician come to look at the dishwasher and he says that it is a problem with the control panel/computer system. Something tells me it is a merely a loose wire and that w


Check your manual to see if you have a drain pan at the bottom of the unit, and a 'float' that checks for water collecting there. On at least some Asko models, water collecting in the pan causes the float to rise, which then changes the operation of ... Asko 24 in. D3112 Free-Standing Dishwasher

Dishwaser whine I replaced the module control assembly after a power surge fried the module. Replaced original module with WD21X10372. When turning the power on. No lights working and dishwasher emitting a whining sound. Can you solve the problem?


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Plastic Pieces We purchased our ASKO 1385 dishwasher 7-8 years ago. Over the years, I have found "small square, thin, pieces of gray plastic" inside. Where are these coming from? Also, we have replaced the drain pump 2 years ago and looks like we'll be replaced the main pump within the next few days as no water is going through. We are looking at paying big $$$ for that pump. Almost half as much as purchasing a new dishwasher. Is this a common problem?


Yes, I have the same problem and it is the upper bearing rack, not the pump impeller. The new bearing kit is $30.00 (another is available for $123.00-the same!!). ... Asko 1385 Dishwasher

Dishwasher (Whirlpool Model DU930PWQ0) won't pump out. Problem occurred after door was opened during a cycle. Then the pump-out function ceased to work. Washer fills and pumps correctly during the wash cycle. Any suggestions? My guess is that the electronic control may be faulty and it is not opening the solenoid valve for the drain cycle. The other option I have thought of is that the solenoid valve may be faulty and is not responding to the signal from the controller. The dishwasher is n


... Whirlpool DU930 Built-in Dishwasher

The pump is working and drains the DW if you pour water into the drain. The problem is that this thing appears to be stuck in "drain" mode always pumping out not advancing through the cycle no matter where you turn the control knob to.


You probably have a stuck solenoid which routes the water either to the arms or out of the machine. It is located near the motor and routes to the drain line. Most are removable and may be disassembled for cleaning. If the control knob does not ad ... Dishwashers

Same problem Hi, I have the same problem there is water in the filter basket of the dishdrawer, I have watched the draining process when itgoes to error F1 and there seems to be a cycle of draining then pushing the water back through again. I have checked for blockages as advised above with a wire, no blockage, I have also blown through the outlet hose to the drain and there is no blockage. I am thinking the blockage maybe in the contained section of the pump as the previous man has explained. T


Hi, \015\012Below is the service manual. Use the FU (fill water) function in the diagnostics and then use P2 to drain the water. Open the drawer and watch will testing.\015\012Good Luck\015\012 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any error codes, New World sent a replacement PCB which made no difference except now have no error code. Circ pump, inlet valve, heater, drain pump checked independantly all worked.


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1715 seconds