Having problems with your Bosch SHE56C02UC / SHE56C06UC Dishwasher ?

HAVE ERROR CODE E1, WATER IS NOT HEATING UP . NO VOLTAGE COMING OUT OF CONTROL PANEL TO HEATING ELEMENT


Answers :

Macmarkus \015\012Rank: Guru bosch.gif dishwashers_small.png
\015\012Rating: 98%, 1499 Votes
\015\012\015\012\015\012Hello,

Welcome to FixYa.
\015\012
\015\012The error code on your Bosch indicates a heating fault has been detected. To determine why you'll need to run a diagnostic program and perform a couple of test's. I can provide the data of what to look for but you will require a multimeter...preferably one that includes a "clamp on" ammeter to measure current or the amount amps being drawn.
\015\012
\015\012First to enter the diagnostic...
\015\012
\015\012macmarkus_59.jpg
\015\012
\015\012To interpret errors,
\015\012
\015\012macmarkus_60.jpg
\015\012
\015\012Then finally the test to determine if you have a faulty heater or a control...it's typically the heater relay on the control itself.
\015\012
\015\012macmarkus_61.jpg
\015\012
\015\012Let me know what you make out of this info or if any of it is not clear you can post your email address and I'd be happy to send you the entire service manual as an attachment to an email.
\015\012
\015\012Thanks for choosing FixYa and good luck. If this indeed was all the info you require or solved the problem please take a moment to rate the info when you're completed.
\015\012
\015\012Thanks again,
\015\012
\015\012Regards,
\015\012
\015\012Macmarkus :)
\015\012
\015\012
\015\012
\015\012
\015\012
\015\012
\015\012
\015\012
\015\012
\015\012
\015\012
\015\012
\015\012
\015\012
\015\012

Repair Help & Product Troubleshooting for Bosch SHE56C02UC / SHE56C06UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

HAVE ERROR CODE E1, WATER IS NOT HEATING UP . NO VOLTAGE COMING OUT OF CONTROL PANEL TO HEATING ELEMENT


Macmarkus \015\012Rank: Guru ... Bosch SHE56C02UC / SHE56C06UC Dishwasher

Ken wood kdw60w10 dishwasher no hot water, there seems to be no power to the inline heating element, showing 30ohms resistance and power directly applied when removed from the dishwasher and it heats up. No fault codes on panel, works normally apart from no hot water, any other ideas? Many thanks


... Dishwashers

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

I have a Fisher & Paykel 913T soft touch dishwasher. On all types of washes when the wash cycle starts there is no 230 volts on the element & after 5 minutes the wash cycle finishes & then goes onto to the next cycle. None of the wash or rinse cycles heat the water but on the dry cycle their is 230 volts onto the element & dries the dishes OK. Is my problem the power supply PCB or could it be the Controller PCB? Does the 230 volts to the element on dry cycle come from the same cicuit on the po


Have you considered the possibility the water temperature sensor may be faulty.\015\012\015\012If the controller is getting false water temp reading then it may never turn the heater on.\015\012\015\012Generally with FP dishwa ... Dishwashers

HOD6615 Vision one dishwasher - water is not heated, errors after 15-20 mins. Element seems to meter out ok, is this more likely to be the safety switch or control panel, any tests to prove. Could anyone tell me what part the safety switch plays in element connection.


... Hoover Dishwashers

HDW101SS does not heat water. Heater element mearures 28 Ohms. Temp Limiter is N.C. Temp controllers TS50 & TS60 not found. On economy wash timer moves as normal then stops when red heater light should come on. If the timer is assisted one click it will progress as normal but no hot water.


Hi.If the temp limiter shows no continuity, there will be no voltage reaching the element contacts. The high limit is connected in series with the heating element. If the hi limit is open the element will not get power. Any technician wil ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

No heat up of water or any temperature raise . Dryning not in functing either . Heating element without voltage supply, during normal sequence of operation. Has found relay Eberle with part no T-nr 3940620 in investigation of electrical loop. Please come up with a possible malfunction . Thank you very much Best regards Erik Rasmussen


... Miele 24 in. G665 Built-in Dishwasher

I have a whirlpool dishwasher DU915WKSO: when I turn the dishwasher on, the heating element comes on but no water comes into the unit. I recently replaced the garbage disposal and th dishwasher worked fine for a time or two. Since then I have only been able to get water in it once. Like I said, the heating element works but no water in the dishwasher. Thanks for any help.


... Whirlpool DU1055XTS Built-in Dishwasher

I have a Bosch SHV55M03GB dishwasher which does not heat the water. The programme cycle also sticks at the last minute. Any ideas, heater element or control panel? Thanks.


If cycle proceed normally after waiting for a while, then the control is probably OK. It stands by a while because it does not read correct temperature before proceeding.If the appliance is connected to both hot and cold water, open more ... Dishwashers

Kenmore Elite Stainless Steel 24 inch tall Model 66577963K701. The heating element works for "heated dry" but not for "Hi Temperature" wash. It used to do so and when I opened the door a nice blast of steam would come out. My hot water tank is a great distance from the washer so we usually run the hot water tap in the sink for a bit until hot water comes... but the heating coil no longer kicks in on any of the cycles (Smart Wash / Normal Wash ). The high limit switch works and as I said, th


... Kenmore Dishwashers

I have an Indesit IDL500 dishwasher. It had stopped heating the water up, it looked as if it had short circuited and so i replaced it, i have power going to the element. A couple of forums state that it may be the pcb behind the timer/selector switch. Does this pcb control the program selection and heating of the element? or is there a thermostat that controls the stop and start of the heating element? Any help would be greatly appreciated


Hi\015\012\015\012The unit\015\012has two thermostats and you can test both of them for continuity before\015\012replacing, no continuity replace the thermostat. Hope\015\012this helps...please post back fo ... Indesit 24 in. IDL500 Built-In Dishwasher

Our dishwasher was taking in water, circulating it but not heating it up or moving through the cycle. My husband took the control panel off and there were some scorch marks on it so we got a new one. He replaced the control panel and the dishwasher went fine for one night. It heated up and washed everything perfectly. The next day when we put it on it was back to square one plus the lights on the control panel are now not working. Just wondered if anyone has any idea what we could do or are


Yes it's time to visit the dump ... Siemens 24 in. SE64A630GB Built-In Dishwasher

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Water not heating up and heating element not heating up either. Water is hot when coming into dishwaher.


DSBELL, see if your model has a serial number in the range of FR3701001 to FR5008380. If so they had a quality issue with the heater. The element itself should be round and not angular. Call for service, it will be covered. If this is not the case yo ... Whirlpool GU2400XTP Built-in Dishwasher

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a GE dishwasher model GLDL560N10SS. I noticed a burning smell coming from it the other day and then realized that although I can hear water running into the dishwasher when I start it, it never actually runs in the sense that the water is pushed through the various outlets to wash the dishes. I'm assuming that it is because the unit is dry and the heating element is still coming on that it is causing a burning smell. If I open the unit and reset it, it pumps the water back out into the si


The problem sounds like it is in the water inlet selonoid. Pull off the bottom panel and this is the part that the main water line hooks to there is a selonoid and it has a plugg inconnection to it unplugg it and check for power when the unit is supp ... Dishwashers

Ok so my dishwasher wasn't heating the water and wasnt completing a cycle and throwing up a code 3 ....I changed the element which heated the water first time but it has now gone back to not working


Seems it may be switch related. More info please. Thnxhead.ready(function(){ fixyaVideo.embed('E515D91','8096481','1_vvb0s80h','976401');}); ... Dishwashers

Hiya, I have a Bosch Dishwasher SGV4313GB that wont heat the water, it gets stuck with cold water continually washing (pre wash??) the delf. Its a built in and I have opened the inside metal panel and exposed the control unit (PCB) there is no blackened/loose soldered joint to be resoldered. I am at a loss as to what else in the heating circuit to look for. Can you point me in the direction of what I should look for next? Kind regards Mark


... Bosch Dishwashers

FDB834RFS0 FRIGIDEAIRE DISHWASHING M# FDB834RFS0 Precision Wash System.... All control panel blinking.... Main power turn of and repower then ONLY HI TEMP WASH and NO HEAT DRY LIGHT ON. How do I enter control panel mode to clear blinking lights? Could it be faulty element inside dishwasher? Any suggestions gladly appreciated. Tks .. AA


... Frigidaire Dishwashers

Zanussi zdt6053 in built dishwasher not starting. When pressing the control panel on/off button the 65 deg normal wash light comes on. When pressing the program selection button nothing happens. When closing the door the machine does not start up. Is there a fault in the control panel circuit board? Would water pressure prevent the machine from operating?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

I have a Miele Dishwasher G1023U , after pressing on/off button the control panel light comes on in the drying cycle not the Wash/Rinse . Water does not come into the machine , can not turn it off at stop/start button only at Main on/off power button. Only had Dishwasher 2 weeks, was working fine. The water tap is on, no kinks in hose.


... Dishwashers

Asko D1776 - Heating element stays on after the cycle has ended. I have to turn off at breaker panel to shut down. What part controls this heating element?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your description it is likely a faulty control board, unfortunately. Here's what you can do to check...\015\012\015\012**Turn off a ... Asko D1776 Stainless Steel Built-in Dishwasher

My Maytag Model # mdb7130aww will not fill with water. I did the auto function test and it completed without any codes but when the water valve was supposed to come on, it didn't. Everything else functioned. I tested the resistance of the valve and my multimeter went from 1 to .90 or so when I checked the terminals. Also, this problem is intermittent and when I check the voltage to the valve it reads around 70 unplugged and 120 when its plugged up to the valve. Does this mean the water cont


... Maytag MDB7130 Dishwasher

The dishwasher does not drain the water out entirely. There is now water left at the bottom of the dishwasher. The water comes up to the heat element.


... Frigidaire FGHD2433KF Builtin Dishwasher

Hello, I would appreciate if you have any suggestions regarding my GE dishwasher. It turns on and seems to want to work but the rinse cycle does not produce any water, it makes noises like the water is coming out and rinsing but when I open the dishwasher the dishes are not wet. I've checked the water valve, turned the control panel off and on, I'm wondering if it is just clogged, any suggestions? Thank you.


Hi,\012Here is a tip that will help you to find out why water will not come into thedishwasher... Dishwasher Trouble No Water entering Dishwasher ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1869 seconds