Having problems with your Bosch SHE6AP0 Builtin Dishwasher ?

Countdown display is flashing saying 2:10 but dishwasher does not respond to pushing any of the buttons (light stays on Power Scrub and does not respond to selecting other wash cycles). On'Off button works but none of the other buttons responds. Machine does not begin washing when door is closed


Answers :

Repair Help & Product Troubleshooting for Bosch SHE6AP0 Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

Countdown display is flashing saying 2:10 but dishwasher does not respond to pushing any of the buttons (light stays on Power Scrub and does not respond to selecting other wash cycles). On'Off button works but none of the other buttons responds. Machine does not begin washing when door is closed


... Bosch SHE6AP0 Builtin Dishwasher

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

I have a maytag mdb6650 aww dishwasher. The dishwasher just stopped. The light on the control panel is on. If I push the buttons to try a different cycle, the light over light wash remains lit, so the buttons don't seem to respond. I was wondering if it is the control assembly, or if the door switch is not working. The handle cracked a while ago, but if the dishwasher still worked even though the handle had cracked in half.


... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Viking dishwasher M# DFUD142-PSS drains a little bit only then starts refilling, start button is blinking. When pressing the 2 buttons to drain have to press several times until responding then it drains just fine, also no push button light is on when pressing for drain. After doing all this machine worked fine for one wash only, then the same problem again after the wash cycle the water stays in the machine. Please help, thank you


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Kenmore 66516812990 touch pad not responding, cancel/drain button works, but sensing cycles will not operate.


... Kenmore Dishwashers

We have started experiencing a problem with our Kenmore Elite 655.15982 dishwasher. Each time we close the door, NoHeatDry lid would go on immediately. It would stay as is of would go flashing. If you touch any button, LockOn lid would go on. Then no other buttons would respond. And often both NoHeatDry and LockOn indicators would be flashing... We tried turning machine for an extended time on the fuse, etc. At times it would work for some time and then cycle get stuck again at the same p


These errors are due to a faulty control board and needs to be replaced. If its still underranty get it fixed before it expires as it is a costly repair to replace. ... Dishwashers

Cycle buttons not responding option buttons working wont start


... Maytag 24 in. MDBH940AWS Built-in Dishwasher

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

My Maytag NDB9601 will not start any cycle. You can select the cycle and the display will show the time, but the start and delay buttons, located on the front, not the top with the cycle buttons, will not activate. This leads to the dishwasher not working at all. It worked in the morning, but not in the evening. Dishwasher is 1 year old.


Sounds like a possible door switch problem. \015\012\015\012If you take that area of the door apart, check the ribbon cable for keypad. You can clean the connector with a pencil eraser. ... Dishwashers

Our Frigidaire Dishwasher buttons stopped working. If we push normal cycle it will not select as well as other cycles. The last time it happened the maintenance guy came and turned it on and off and it started working again. That didn't work this time. We still can't select some of the wash buttons


You will have to replace that selector switchhttp://tclaundryrepair.com/ ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

Hi, We have a Smeg ST 663 dishwasher that does work. However, sometimes when you want to use it and turn the power button on it beeps twice with the red light flashing and you can't get it to work or change the settings. Sometimes if we leave it for a while and try it again later it will work, but it is annoying as sometimes it won't want to work for ages and we really want our dishes cleaned! The dishwasher doesn't have many buttons on it (a power button, cycle selection button and 1/2 load


Hi,\015\012\015\012Turn machine on and press and hold the programme select button till the light goes out about 5-7 seconds see if this resets it if it does start a cycle and see what happens.Otherwise the pcb as its not responding to an ... Smeg Dishwashers

Maytag 24 in. MDB8951AWS intermittent button problems and incomplete wash cycle. The buttons work sometimes ... sometimes not. We also have experienced incomplete wash cycles when the buttons do let us start a cycle. Sometimes it completes correctly. Suspect control board, as I expect a membrane failure to cause incomplete cycle unless it is making a Stop/Cancel contact by itself. Can anyone chime in on thoughts?


... Maytag 24 in. MDB8951AWS Stainless Steel Built-in Dishwasher

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

Hello, Our kitchenaid DW has stopped working. Non of the buttons cause a any of the lights to turn on. Of course, it will not start. On its last working cycle, it had a very strange washing cycle. It almost sounds like the water was not splashing around (even though I opened it while it was working and noticed water at the bottom). I checked the circuit breaker, and it is not tripped. For a couple of weeks, the DW had started making a kind of metallic noise while in the washing cycle. Also,


It is nice to see a problem described with such a depth of observations. It helps in closing on to the possible causes of the problem.\015\012\015\012For the moment let us make sure there are no remnants of the glass left in the dishwashe ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

Has power all the way past the latch, but cycle selection buttons dont respond


Hi nipdoes2,\015\012\015\012I'm Harvey the Master Plumber.\015\012\015\012Your problem is: You followed the power as far as the door switch.\015\012\015\012If you follow it past the door switch you'll find a bad c ... Whirlpool SUD6000HQ Dishwasher

Cycle buttons working. Start button not working.


... Kenmore Dishwashers

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Controls do not respond, only the drain button works.


Hi,Could you run a diagnostic test for me and let me know what happens? It takes about 10 minutes and will shut off at the end of it. It should do the following:Fill with water for 2 minutes,Main motor for 2 ... Whirlpool 24 in. DU915PWP Built-in Dishwasher

Hi, I've got a dw 681es wh nemo dishwasher. I turn it on, it starts working but it sounds funny....and nothing happens. after a while the start/reset button flashes and then it doesnt continue. Any clues? I start it on the quick wash cycle but it quickly flicks to the rinse cycle when this problem occurs. I used to just reset and it worked again but now it just wont work.


... Fisher and Paykel Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0992 seconds