Having problems with your Bosch SHU3036UC Dishwasher ?

Bosch SHU3036UC draining on wash cycle

\015 Our Bosch SHU3036UC dishwasher does not drain at the end of the wash cycle, it seems fine on the rinse cycle. The water that is left at the end of the wash cycle is clean so it seems like the wash cycle is not completing, as opposed to the drain having a clog in it.\015

Answers :

It is probably going to be a grimy door thermostat between the inner and outer panel. its hooked into the back of the soap dispenser. someone would have to take the outer panel off then clean wipe away the caked grime from the thermostat and put it back in its place. if this doesnt fix it then it could be a heat assembly problem or timer problem. in that case you would need an appliance tech out
Repair Help & Product Troubleshooting for Bosch SHU3036UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch SHU3036UC draining on wash cycle


It is probably going to be a grimy door thermostat between the inner and outer panel. its hooked into the back of the soap dispenser. someone would have to take the outer panel off then clean wipe away the caked grime from the thermostat and put it b ... Bosch SHU3036UC Dishwasher

Bosch dishwasher My Bosch dishwasher finished a wash cycle and was showing the "END" light on, however, the motor was still running as though it was stuck on the drain cycle (there is a gurgling sound from where the eater drains off beneath the filter. Subsequently turning the washer on just repeats the apparent drain cycle with a constant gurgling sound (it does not kick into wash mode). The number on the manual is & 258 (7705).


Is all the water draining from the tub? if not the pressure switch will not reset and it will continue to try and clear it self...check drainage system.\015\0122. pressure switch is jammed on..build up in the sensing chamber..commo ... Bosch 24 in. SHU43 Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

My Bosch dishwasher won't drain at the wash cycle, continues to 1 minute and won't drain or finish the cycle. We have checked the drains, the hose and tried different cycles all with the same results of unfinished washing.


... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher

I have a Bosch dish washer model SHX 43 M 0 ZUC / 48 FD 8709 00169 The dish washer is about 1 1/4 years old and was installed by a plumber as part of a Home Depot kitchen remodel. The problem is draining. The quick wash does not drain at the end of the wash. The regular wash sometimes drain and sometimes does not. The auto wash does drain. The lack of draining does not cause problems with the regular wash cycle. I checked the drain hose re the instruction manual and it is correctly installed.


Usually a brush with a flexible shaft will do the trick...\015\012\015\012Like this venturi tube cleaner (available where gas grills are sold)\015\012\015\012 ... Bosch Dishwashers

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

Bosch Integra SHU 9955US/12 - when we start wash cycle, the detergent dispenses and the tub fills with water, but the wash cycle never starts (never spins spray bars). Seems like timer is counting down, though, but doesn't start "washing". After waiting awhile, we are able to use the "Cancel/Drain" mode to drain the water. The drain filter in the bottom of the tub is clean.


Sounds like your motor is burned out. The drain motor and wash motor are seperate on your machine. You can check for power going to the motor, but to do this you might have to pull the dishwasher out. While the cycle is running check for 120 VAC g ... Bosch SHU9955UC Built-in Dishwasher

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

Bosch sgs43eo2gb dishwasher. wash programme completes, water drains out, but machine goes on draining, forever, stuck at around 50 minutes on the facia clock. there is no leak on the machine and everything else has been cleaned and operates perfectly. ie,fills correctly,heats correctly and drains fully but won"t stop draining & refill. Cancel programme and reset and it works perfectly until end of wash cycle again, when it continues to drain even with the door open. There is no leak in the machi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. Please once again check that the hoses are not kinked or drain pump and filter ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch dishwasher Does not heat up in the washing cycle and does not drain down at the end of the cycle. End of cycle the display sticks at 1 and the drain pump operates until the machine is switched off or reset. Followed the suggestion in another thread to look for a burnt solder joint on the control board. Unfortunately my machine is a later model than the board shown and has no poor joints on the board. It would seem from previous answers that the problem is either the controller, the heating


1) The water must be preheating by heating elements and thermostat see how to do it.\015\0122) Timer , test for defective,clean the contact, repair wires for loose, broken, or burn.\015\012\015\012God bless you.\015\012 ... Dishwashers

I think I need to check the water pump/motor on my Bosch SHU43C dishwasher. It seems the water enters at the start of the wash cycle but then there is silence through the remainder of the cycles. Water will not spray. The drain appears to work ok to drain most of the water out. I have the washer out and upside down. Any hints on removing the base to get access to the pump? Should AI be looking at the control panel also for a fault? (the cycles seem to count down ok)


Click below;\015\012Latest Bosch Dishwasher Use and Care Manual\015\012\011\011\011\011May 4th, 2008 by Samurai Applian ... Bosch Dishwashers

I have a Bosch "Classic Electronic" dishwasher that has been in use for only 18 months. If it helps - SGU53E05AU/30 is marked on top of the door.. my problem is that on the last cycle, the water won't drain so I am left with lovely clean dishes but there is water up to the drawer line present and it won't drain until the next wash. I have cleaned all the filters and ensured the pipes are not obstructed. It is odd that it only does it on the last cycle. Could it be the microchip?


Hi there,\015\012\015\012thank you for providing the model #, that helped me narrow down the troubleshooting.\015\012\015\012try the following to fix your problem:\015\012\015\012check for blockage or kink in the d ... Bosch Dishwashers

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Bosch SHE44C05UC/43 dishwasher about 2.5 years old. It just started recently to stay in the wash cycle forever. The number on the LED panel decreases in the normal fashion, but the dishwasher never changes from the wash cycle to the drain and then rinse. I have verified the incoming water temperature is adequate


You must change the module. that will solve your problem. let me know how you made out.:) ... Bosch 24 in. SHU5305UC Built-in Dishwasher

Bosch dishwasher SHE44C02UC, serial # 13693156: Does not cycle. I turn off and drain by pressing "Regular Wash" and "Rinse and Hold" together (need several of these to completely drain), then rinse by starting cycle and repeating above sequence. Slight burning smell also - motor? Is there a way to initialize the sequence, and if there is, is it advisable, given the slight smell? Robert Langridge


Hi\015\012\015\012First, try to hear a hum like sound from the motor however, the burning smell indicates that the motor is unable to work. You can also check that the motor is work ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Bosche 4803 dishwasher, fills, drains but water not reaching wash arms during the cycle, even though I do hear the motor for when it should be happening. Have cancelled drain and restarted multiple times. Checked filters, removed wash arms and verified cleanliness and water passage.


... Bosch 23 in. SHU303 Built-in Dishwasher

Bosch dishwasher won't drain...it washes the dishes great but there is water remaining in the bottom after the wash cycle is finished. I have done the following with no results: 1. checked drain hose to sink and it was clear of debris 2.removed filter and cleared it out as well as removed the bottom cover and checked there...looked clear. please help


Hi\015\012\015\012There are a few things to check with this problem on Bosch Dishwashers. \015\012\015\012As always for safety reasons disconnect the dishwasher from the mains supply before carrying out these checks.\015 ... Bosch Dishwashers

Bosch dishwasher model SHV6803UC/12 - washing cycle finishes with substantial water in pan. Dishwasher turns on intermittently following cycle and drain small amount of water but never close to completely draining pan.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I`ll start by letting you know there are many things which can manifest in the manner you`re describing...or even how one interprets what you`re ... Bosch 24 in. SHX46A05 Stainless Steel Built-in Dishwasher

My Bosch diswasher water inlet work fine, when the wash motor or cycle need to start nothing happens. The timer is advancing normal. Water outlet(drain pump) is also working fine. There is no woosh sound (start of wash cycle) and arms is not rotating.


Hi,\015\012\015\012it sound's like the wash motor is either seized or just stuck, let's hope it's the later. Bosch had issued a service tip about this problem several years ago titled "Loosening Frozen Impellers" strange choice of word's considering ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Our Bosch Dishwasher Not Draining After Normal Washing Cycle


Make sure the filter is not blocked by anything like a straw or just junk ... Bosch Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

I just replaced the drain pump in my bosch shu3307uc dishwasher.When I turned it on it filled with water and then I put it in the drain mode' It drained but it would not allow me to advance to start the wash cycle from the beginning. How do I advance this unit? It was working fine until drain pump went out.


You have to allow the drain cycle to finish completely, or find cancel drain dot points and press both at the same time, to reset program, open the door and close it to make sure the micro-switch activate properly ... Dishwashers

Bosch dishwasher I have a month old Bosch dishwasher. It was stopped mid cycle. I drained the water at the bottom, but the active light keeps flashing, and when I press the start,reset button, then turn it off, it does the same thing when I turn it back on. active light keeps flashing and the wash light is on. It won't even lock the door. How do I fix this because there is no Bosch dealers here to help with the problem.


... Hotpoint 23 in. BF41 Built-in Dishwasher

Bosch dishwasher is permanently draining even when the door is open. The draining usually does not stop, but on the occasions it does the wash cycle only last a few minutes before it draining again.


THERE IS A FLOAT WITH A RED SHAFT /LEFT SIDE AS YOU LOOK INTO THE BOTTOM OF MACHINE. AFTER TAKING OFF KICK PLATE. IT IS GOING TO DRAIN IF THERE IS A LEAK FROM PUMP OR HOSES FILLING UP THE PLASTIC BOTTOM OG MACHINE . KEEPS A LEAK FROM GOING ONTO YOU ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1017 seconds