Having problems with your Bosch SHU4006 Dishwasher ?

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


Answers :

The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.
They only cost $20 each. The Control Module is close to $200.
SOUNDS TO ME YOUR CONTROL MODULE IS NOT WORKING CORRECTLY
Repair Help & Product Troubleshooting for Bosch SHU4006 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

I have an old (not sure what year, 80s?) Kitchen Aid energy saver V Custom by Hobart dishwasher. We opened the dishwasher in the middle of a cycle and now cannot get it to re-start. When we lock it back up and push our normal buttons (Low Energy and Energy Saver/Dry Heat Off) or any other combination of buttons, the dial does not turn automatically and the cycle does not continue. I have also tried advancing the dial manually and still, nothing happens. I have even tried advancing it all the


... KitchenAid Dishwashers

I have a 1999 bosch SHU 4300 dishwasher given to me. It worked great for about two weeks. Now it takes for ever *3-4 hours* to complete a cycle (if it does). I have opened the door to see it filled with sudsy soap after this long. I have checked the hoses and they are not kinked. Once the cycle of cleaning is over, If I reset it manually, it will rinse the dishes and empty just fine. But I have to manually get the dishwasher to advance to the rinse and dry cycle every time now.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SHU43 Built-in Dishwasher

My Bosch SMU2000 series dishwasher will not complete the wash cycle. Advancing the dial completes the cycle but it sticks again before completing the rinse cycle. I replaced the timer assembly and the symptoms are the same


Hi,It seems to me a Faulty Control Board. You need to pull up the control board and check the resistors on it. If found burned or swelled, needs to replace those.Note - It's better to replace control board than to repair as yo ... Dishwashers

I have a Jade RJDW2470A dishwasher which was re-branded Jade. (It is a Maytag product.) It get's stuck between cycles and will run forever unless I manually advance the dial to the next cycle. It seems to get stuck around the "rinse" cycle and the soap door does not open until after I advance it past that cycle.


... Jade RJDW2470A Free-standing Dishwasher

I just purchased the Haier HDC1804TW/TB/TS countertop dishwasher today. I have it all hooked up but it won't run a complete cycle - all lights flash which the manual indicates excessive amount of water cycle not completed...allow dishwasher to complete full cycle...ummm...i'm not keeping it from doing so...help!


... Haier 17 in. HDT18PA Built-In Dishwasher

Dishwasher when turned to usual dial number hums enthusiastically but does nothing, no water, dial does not advance. If dial is advanced manually, some cold water is produced; dishwasher tablet is released but not dissovlved. All rotor arms and water intake areas are free of obstacles and blockage (as far as we can see). Any ideas?


Removed the filter and shopping for a replacement. An "in progress" report - not completely solved yet. ... Dishwashers

KITCHENAID KUDSO3FTSSO DISHWASHER WILL NOT COMPLETE CYCLE. STOPS NEAR END OF CYCLE AND THE START/RESUME BUTTON FLASHES. YOU HAVE TO MANUALLY HIT THE START/RESUME BUTTON TO COMPLETE CYCLE.


Https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a4 ... KitchenAid Dishwashers

Hello, my Hoover D7610 dishwasher has developed a problem, I would appreciate your advice.On starting a wash it appears to be working OK through what I believe to be a rinse cycle but then after about 20 minutes water pours out from the bottom of the door. Manually clicking the timer-programer forward stops the leaking but the machine needs manual advancement except for the last 2 cycles when the timer seems to work OK. After the 1st cycle there is no more water leaking from the machine but all


... Hoover Dishwashers

Model No. DU850SWPU3 AND SER. FT 4101406 TYPE 280-0. When cycle is complete and in off position the dishwasher fills with water. I find the bottom of the dishwasher standing full of water when I get ready to fill with next load of dishes. When I remember to turn off the wall switch this does not happen, however once in a while I forget to turn off the wall switch. The next day I find the bottom of the dishwasher full of water again. I then have to go through the cycles manually a couple of tim


If by turning the wall switch off, and only then it stops comming in, it means the board is faulty. There is a leak in the electronic system allowing to solonoid to stay partially open. Strangs that it doesnt flow onto the floor. ... Whirlpool GU2400XTP Built-in Dishwasher

My GE Monogram ZBD4500 dishwasher does not drain completely at the end of the cycle. If I run a couple of manual cycles afterwards it eill eventually drain completely. Drain hose is clean, pump suction sump looks clean, drain pump impeller appears OK, discharge check valve assembly is easy to blow through in direction of drain. Do I have a sequence switch problem?


I bloody lostt you! are you still there? ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Dishwasher was on and had a power cut for no more than 5 mins. since then dishwasher dial will not move round on its cycle so ends up being on forever if not manually turn dial


... Hoover 24 in. HD98E Built-in Dishwasher

Dishwasher takes about 24-36 hours....yes hours....to complete the cycle because it stops....for sometimes more than an hour and then starts again on its own. When it stops the green light blinks. No explanation in the manual for a blinking green light. It will eventually complete the cycle, but who has two days to do a load of dishes?


... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

My Teka Dishwasher DW7 80 FI does the first water intake operation, it sounds like rinsing, and the you hear the pump evacuating the water and two beeps as when it finishes the complete cycle. About 6 minutes. Then Stops. The lights that stayed on says error E8 according to the manual. I have done the suggested fix as ending the cycle manually and turning off and on the DW. I tested "many" times in various modes and the same preemptive end.


Hi.E8 is alternate washing system malfunction.The alternate washing system consists of a valve located in the underside of the appliance and connected to the impeller motor. The valve opens and closes switching spray on and of ... Dishwashers

Blanco BFDW4X Dishwasher - dial will run any of 3 cycles down right side, and then click back to start position, but will not automatically run the rinse down left side of dial, have to turn the knob manually. Also looking for a manual for this.. Susan [email protected]


... Dishwashers

Miele 868 dishwasher-water fills at begin of cycle,but pump/wash cycle doesn't engage(timer dial still advances,drains at end of cycle.dishwasher was workong,but was moved to a new location ans hasn't worked since.impeller moves freely and pump was rotated via 8mm hex key.is there possibly a reboot/reset, or is there possibly a water pressure issue?-I didn't think so as the dishwasher fills to the prescribed level.


... Miele Dishwashers

I added 3 cups of water to the dishwasher DD24DT top drawer as directed to check the rinse cycle. I pushed the start/pause button, I hear some noise, but the dishwasher does not completely turn on., there is an icon with two arrows, like a cycle symbol. I did not get a manual with detailed instructions so need help!


... Fisher and Paykel DD24DT Builtin Dishwasher

Haier hdw101wh.The dishwasher starts when you turn the dial the pump discharges waterto the outlet it clicks to next cycle but remains washing will not cycle through the wash cycle it keeps on washing . You have to turn it manually to get it finished any info will be appreciated.


... Haier Dishwashers

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

Our Ariston LI645A dishwasher is not drying the dishes completely and whenever the cycle has finished, it always resorts back to the ECO cycle whereas we usually have it on the normal cycle? I have filled up the rinse aid but it does not seem to make a difference. The manual also says to put refined salt into the salt dispenser - i have not done that yet as was not sure exactly what 'refined' salt is and where i can get it from. thanks


... Ariston Technologies Dishwashers

I have a Frigidaire Ultra Quiet II dishwasher that gets stuck in the 6:00 position (between light wash and drying) during the cycle. It also gets stuck right before the drying cycle. It will proceed with the cycle if I manually move the dial. The heated drying feature is also not working as well. Do you have any suggestions? Thank you for you time, for it is appreciated. Best Regards, Scott G.


... Dishwashers

Whirlpool dishwasher model DUB700XB has quit cycling. Fills with water but will not start wash cycle. Making intermittent humming noise unless the door is open to disengage the switch, even when on stop. No LEDs lighting when rotating the dial through the various cycles. Unit is old and wondering if it's better to buy a new one rather than fix this and have something else go wrong in the not to distant future. Thanks in advance


... Dishwashers

My dishwasher was working fine til this a.m. Making a loud buzzing noice when clicking into a different cycle. Had to manually nudge the dial to move it to the next cycle to stop the loud noise. This happened several times during the washing cycle.


... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

Smeg dishwasher not completing the cycle. Stops after each part of the cycle. Needs to be manually set again for the next part of the cycle.


Hello,\015\012Can you post what model the dishwasher is?\015\012Thanks,\015\012ajs_biz ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1789 seconds