Having problems with your Bosch SHU5315UC Dishwasher ?

The dishwasher has been running for 3 hours and seems to be stuck on 1 minute left. Upon opening, there was sudsy water remaining in the bottom, but the dishes looked clean. The washer just won't go to "CL" in the digitial window. Thanks for your help


Answers :

SHU 53 MODELS\015\012\015\012To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jumper). When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button.\015\012\015\012To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone). Cycle Countdown display will show ?88″ when REGULAR WASH button is pressed and ?8h? when Delay Start button is pressed.\015\012\015\012To start testing, press both the SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ ?6? = faults 2 + 4).\015\012\015\0120 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault\015\012\015\0121 = Aqua Sensor (?Sensotronic?) fault 4 = Filling fault F = Filling fault (display occurs during wash, not test)\015\012\015\012To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.\015\012\015\012If water level switch (f1) has failed (opened), display will show fault code ?4″ and unit will continually fill and drain where testing won?t be completed. If flow switch (e5) has failed (opened), display will show ?0″, water won?t heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code ?8″ immediately and testing will end shortly after water has started circulating.
Repair Help & Product Troubleshooting for Bosch SHU5315UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The dishwasher has been running for 3 hours and seems to be stuck on 1 minute left. Upon opening, there was sudsy water remaining in the bottom, but the dishes looked clean. The washer just won't go to "CL" in the digitial window. Thanks for your help


SHU 53 MODELS\015\012\015\012To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jum ... Bosch SHU5315UC Dishwasher

Bosch dishwasher model SHV66A. New in 2004. Has worked well since then, but for last couple weeks something's up. Dishes aren't clean. Residue remains on everything. Food looks caked on & dried to plates. Silverware a little better but not much. Tried running a couple cycles with vinegar, no help. Took out strainers, etc. on bottom of washer & cleaned out; no help. Just ran a cycle now - - opened midway and it appeared the arms were both spinning. Also, water seemed warm (maybe not super


Hi\015\012\015\012If you are observing that the dishes are\015\012not clean, then you'll need to follow certain steps to be sure where exactly\015\012the issue. First thing to check for is\015\012the deter ... Bosch Dishwashers

Not cleaning dishes especiialy the ones on top rack. Found some broken glass pieces in bottom. No obstructions in line leading up to top washer. It looks like the pump is not pumping enough water pressure and/or volume for the top washer to function properly. Please help. Whirlpool Quiet Parnter I. Approx. 2-3years old.


If you remove the filter in the sump area underneath the lower dish rack (removing the screws to do so) you may find debris blocking/jaming the impeller area. Be very careful of almist invisible broken glass. Inspect the impeller to make sure it is ... Dishwashers

Hi! My bosch SHE43 built in dishwasher is about 2.5 yrs old, dishes aren't getting clean anymore. We have *really* hard water so I use the max rinse agent, but doesn't help. I clean the little canister filter with each wash, and just washed off that grate in the bottom. I also just cleaned the trap under the sink, but it didn't look bad at all. The problem is a grit left on glasses and things just not getting all the way clean. When I remove the grate at the bottom, there's a bit of water


Hello. Let's begin by tossing two cups of vinegar into the empty dishwasher and running it on it's hottest and longest cycle. Always run the hot water in the sink faucet until it is as hot as it gets before starting up the machine. Let that cycle ... Bosch SHE43C02UC Dishwasher

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Hi,Check your heating element.. Dishwasher ... Kenmore 15899 Built-in Dishwasher

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. Also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Best off to call a certified repair company such as Sears. ... Kenmore 15899 Built-in Dishwasher

The top rack dishes do not get cleaned. I have run the vinegar rinse. The bottom rack dishes get cleaned. It doesn't even look like the top rack dishes get wet. I ran the washer without the top rack in and I think water was coming down from the top. What can I do?


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Dishwashers

For Miele Dishwasher G2470SCVI Need help with remaining water in the bottom. Model# G2470 SCV1 SF Type-HG03. Runs through the entire cycle,long,short ect..everything is clean and dishes look great but


See this causes and fix it. God bless you\012 \012 \012 \012 \012 Belt, Water Pump\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

8 year old maytag, clean lime build-up 2 times a year and all the spinning parts look clean and no wear but all of asudden the washer does not clean the dishes very well. Plenty of hot water, soap is dispenced, cleaned screan in bottom, don' really see anything out of place. what could the problem be? Thanks Rick L.


Hi,\012In you case check the heating element first...\012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... \012 ... Maytag Dishwashers

Some of the dishes on the top & bottom are not coming clean. Is there a filter that gets plugged? I am not cramming dishes in & I run the hot water to really hot before I start the washer. I also rinse the dishes before putting them in. HELP!


It sounds like water supply problem hose may not feed enought water ... Kenmore 24 in. 15079 Built-in Dishwasher

I have a ADG450 about 7 years old, the problem is there is dirty water left at the bottom of the dishwasher after finishing the cycle and the dishes look as if they have had the final rinse in the dirty water. also i have tried the rinse cycle with no dishes and all the rinse water had not drained away. I have cleaned the iside of the washer and where the water goes to the pump. Any ideas


Check the pipe leading from the dishwasher to the outlet, maybe under sink. this needs to be raise up as water will flow back into washer. Had this problem myself, felt foolish when the repair man just tied it up and left. ! ... Whirlpool ADG450 Slim-Line Built-in Dishwasher

My kitchaid KUDS02 dishwasher is leaking water under the door all day evan if it's not running. I looked under ther bottom panel it's dripping 1 drop per second. Seems fine in cleaning dishes but somewhere there is leak. Any help where to start looking is appreciated


... Dishwashers

Doesn't clean my dish washer seems to work fine but when its finished the tablet i put in the door is still in one at the bottom of the dishwasher and the dishes aren't cleaned properly. i've checked it about halfway through and the water does get hot. please help.


Is your water heater set at 120 degrees if not set it to it ... Hotpoint 23 in. BFI62 Built-in Dishwasher

The inside of the dishwasher bottom is a film like covering. it is cleaning dishes great, but the stainless steele bottom looks awful. HELP!


You could try running it empty, hot, with a cup or two of vinegar in it. ... Jenn-Air 24 in. JDB1090AWS Stainless Steel Built-in Dishwasher

Asko dishwasher- about 1 year old. Dishes are clean but very wet at the end of cycle. The bottom tub is filled with water (looks clean and warm). The dishwasher is leaking and water on tile kitchen floor. I checked for a float device inside and do not see one. What do you think problem is? How can I check hoses to see if clogged- do I need to pull washer out? Is that hard?


... Asko 24 in. 1895 Built-in Dishwasher

The inside of the dishwasher bottom is a film like covering. It is cleaning dishes great but the stainless steele bottom looks awful. Help!


The problem is hard water. www.dishwasherfilter.com has a great new product out that will solve this problem once and for all. It filters the water entering y ... Jenn-Air 24 in. JDB1090AWS Stainless Steel Built-in Dishwasher

Our GE Profile (Quiet Power 6) dishwasher is having trouble cleaning our dishes. The top shelf rarely gets cleaned and the bottom is questionable. It used to work fine. We always use Cascade powder detergent on a normal wash cycle. We have hard water. Any advice would be appreciated. I took apart the washer looking for an obstruction but none existed.


The obstruction can be external to the unit. Check the drain at EACH connection working backward from the sink connection all the way to the motor pump outlet hole. Do not forget to dis-assemble the Air-Gap (if installed) and to check the inside of ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

FDB105OREC4 My dishwasher is not cleaning my dishes. I push the start button and water seems to be trickling in then it stops and no sounds protrude from the machine for several minutes. Eventually another loud motor seems to turn on and drain the water out of the machine. The soap dispenser usually opens and the soap block that usually dissolves is setting on the bottom of the machine. It seems the water is plenty hot but the rotating washer arms might not be moving. Please help me find the par


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have a M4605AL free stading dish washer from Servis. Water enters the chamber for approx 5 seconds after turning on, when does nothing. I have cleaned the draing pipe and have the motor on the bottom checked, when else could it be? please help, now washing by hand!!


... Servis Dishwashers

Dish-washer My dishwasher is not draining all of the water out of the dishwasher after it washes. I got someone to look at the drain pipes and he cleaned out the stuff and they still will not drain all of the water. I would like to know what I could do to get all of the water out of the dishwasher so that the water will come out of the bottom of the machine. Wanda


The problem is most likely that the pump empeller had been damage by pieces from a broken dish or a small piece of siverware. The only way to fix this is to take the dishwasher apart and replace the empeller. If you choose to do this yourself, you sh ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

My Asko D1976 dishwasher is not cleaning dishes properly. There is a lot of clumped detergent left in the dispenser after wash cycles are complete, and many of the dishes have dried-on food left on them. I rinse dishes before loading them into the washer, I have made sure the jets and washer arms are clean, and made sure the food trap at the bottom of the washer is empty, yet the problem persists. I think it has to do with the detergent not dissolving and dispensing. Is there some reason the


First of all, don't pre-rinse the dishes. Check the water temperature, it should be between 120 and 140 degrees. Be sure you are not partially blocking the dispenser door so that it isn't opening. ... Asko D1976 Built-in Dishwasher

Model number 66515632000 Kenmore Ultra wash with quite guard about 8 years old Washer stopped near end of rinse cylce, dishes look clean, water in washer did not drain and looks clean. All attempts to restart washer, or hit drain etc result in attempt to start and then it stops. sounds like trying to start a car with a very weak battery.


Unfortunately it sounds like you have one of two possibilities. A) You have something like a piece of glass or food ect. that has worked its way down into your pump and is tying up the impeller or pump as its trying to start. -To op ... Dishwashers

Nasty dishwasher there is nasty wet grunge at the bottom of the door, around the place the heating unit in the bottom of the dishwasher. half the time the dishes are clean in the bottom of the dishwasher. half the heating element is melted..for some reason...what do i do. the dishwasher still works, if we make sure the dishes are clean before they go in. using more for a sanitation thing than a dishwasher. can ya'll help me?


Sounds like your heating element is broken and you should replace it to prevent a possible fire hazard. \015\012You can replace the element easily for not alot of cash. You'll need to pick up a new one at an appliance parts store, just bring them the ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Our dishwasher is approximately 13 years old. Today I turned it on and it did not clean the dishes. After trying to wash the dishes three times, the dishes on the bottom rack were clean but the top rack dishes, the door, and the dispensor were not clean. Help.


13 years old?!? LOL, you're lucky it turns on!!!Pop the sprayers off and check for clogs. Otherwise, get a new one, this machine is way, way, way past its life expectancy. ... Magic Chef Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1229 seconds