Having problems with your Bosch SHU5315UC Dishwasher ?

Letter F appears on screen, and dishwasher does not start. Sounds like pump runs for a bit then stops. Door is closed. What is wrong?.


Answers :

Hi
\012
\012Error code F indicates that dishwasher control has detected a fault with dishwasher filling. This is due to faulty water inlet valve. Please check for clogged water inlet valve. Water inlet valve part#35
\012
daniel_s_9.gif
\012
\012You can buy it from this link---
\012
\012Bosch SHU531 water inlet valve
\012
\012
Hope this helps... Please post back if you need more information

Daniel
Repair Help & Product Troubleshooting for Bosch SHU5315UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Letter F appears on screen, and dishwasher does not start. Sounds like pump runs for a bit then stops. Door is closed. What is wrong?.


Hi\012\012Error code F indicates that dishwasher control has detected a fault with dishwasher filling. This is due to faulty water inlet valve. Please check for clogged water inlet valve. Water inlet valve part#35\012 ... Bosch SHU5315UC Dishwasher

I ran my pressure washer today in an effort to run some "stabilized" gas through it for the winter. For some reason the pump began to push oil out the top relief hole. If thats not clear, it's a feature that looks like a priming pump but is rigid. By the way, the oil appeared a bit nourish gray. Not sure if that means anything. Any ideas?


It looks as if moisture/water has contaminated the oil. Check the level of oil from the glass window. It must be high. Drain out the oil & check if water is present, if so then replace the entire oil. ... Dewalt DPD3100 Gas Pressure Washer

Asko 1375 unit will not wash drains and fills ok  motor at back of unit runs well. Suspect impeller   Does motor have to come off for impeller replacement?? My 1375 is leaking a bit, looks like the seal which was mentioned in the impeller repair case,may be the problem? The other problem I noted was a clogged screen at the bottom of the dishwasher which is on the suction side of the pump, the screen had calcium buildup etc. I cleaned it off with vinigar and reran the dishwasher seemed ot fix th


Do you mean to say that the washer does not go into the wash cycle at all, or washes poorly?An answer to both can be found HERE.This article ... Asko 1375 Dishwasher

I have gritty debris on the dishes, it appears the small bits left on the dishes before loading get broken down and rinsed onto them as grit again! The dishes are not spotless going in but they are scraped clean--i object to the waste of hand washing then dishwashing . I did run a load with no dishes and vinegar to clean it, the screen in the drain is clean, I don't know what is missing. Its like it doesn;t drain the dirty water away somehow


1. it can be water backing upfrom maybe a garbage disposer like a clog ,or fill jet dry compartment completely.add nad fill then open and close the door 3 times then you will be able to add more what you are doing is taking out the air in the dispens ... Bosch 24 in. SHU43 Built-in Dishwasher

Our normally quiet Bosch SHX36L Dishwasher has started being noisy while running. I found if I lean on the door it closes a bit, and the sound returns to the level it used to run at. It appears that the door isn't closing tightly anymore, but we can't see an obvious fix for this. Thanks for your time!


Your lock plate inside the machine can be worn but it can also be the gasket of the door. Door gasket is the easiest fix ... Dishwashers

My GE Nautilus DW doesn't fully drain. When it is drained as much as it will it leaves water in the sump at the rear right. If you run the pump at that point, it sucks water out of the sump, but when you open the door and the pump stops water flows back into it. It seems like there is a check valve that isn't working. I have cleaned the sump and the screen which runs accross the rear. I also have taken the plunger out and cleaned it. Then I took the housing for the plugner off the bottom. I don'


HI. check the following areas for fualts.1. Air gap / Drain hosesIf there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: I ... Dishwashers

Bosch built in dishwasher shu4302uc The dishwasher appears to run through the cycle but the cycle keeps running. I have checked the screens and they were clear. I have a Bosch Dishwasher SHU4302UC and I can't figure out how to cancel the cycle it's in. It keeps running and running. It pumped all the water out and the LED indicator are lit for the rinse/dry.


There is a recall on the control board of many of these models. I have written a guide to help. It is here. Look for the phone number near ... Bosch 24 in. SHU43 Built-in Dishwasher

Kenmore Ultra Wash Dishwasher (Mod: 665.1373) makes bad noise after the tub fils and the pump starts running. (Not sure how to describe noise.) Bad pump? Other? I have checked for anything obstructing rotating parts and that is definitely not it. My guess is something wrong with the pump, but not sure. If so, I'm wondering what my options are. Like are their common problems with pumps that can be fixed at home? Replacement?


Definately sounds like a pump on its way out. Probably not the pump itself - but the starting capacitor.However it may be cheaper for you in the long run to have a professional out to diagnose the problem instead of throwing money into it blind ... Dishwashers

It appears that water is not running through the dishwasher or that the sprayers are not working correctly. There doesn't appear to be a clog. However, I did find a round rubber "washer" (I think that is what they are called) laying in the bottom of the dishwasher - where does this part go. It was working fine until this wash. The heating element works fine but like I said it appears that something may be wrong with the spray tower. Please advise Model number of Hotpoint: HDA3420Z01BB T


Hi,\012When my wife started complaining about her dishwasher not getting the top rack clean this is what I found and I wrote a tip about it...Dishwasher ... Hotpoint Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

The water is pumped out after the rinse cycle then it continues to run and make an unusual noise but nothing happens. The noise is almost a grinding sound. There is also a smell like some part may be hot or the wiring may be hot. I can reset the dishwasher and re-run the cycle up until that same point and it does the same thing again. I have had a repairman out twice in the last six months. The first time he could find nothing wrong because the problem was intermittent and he couldn't see anythi


Timer \015\012\015\012or\015\012\015\012 ... Bosch Dishwashers

Dishwasher pump keeps running and f2 appears on the screen. Switched off unit at the plug and switched on but the pump continues and f2 reappears


Tilt the dishwasher back to reset the flood switch and test for leaks and blockages ... Asko 24 in. D3350 Dishwasher

Kenmore dishwasher Have a kenmore 655.15889020 dishwasher which does not appear to be pumping water fast enough. No apparent blockages. Arms circulate very slow. Enough water in sump. Could it be the motor for some reason is running slow? Or maybe some valve is not closing properly.


Fatubu, are you sure you have the correct model number, Im not finding anything on the posted model. They had an issue on models close to this that had an issue with a twisted or missing seal in the pump assy. causing water to fill the pressure swit ... Kenmore 24 in. 16032 Built-in Dishwasher

Water is not coming to the washing machine, when I hold the start button down the pump runs a bit like trying to start but no water comes in. The water connection is OK but is there anything else we c


Is this a dishwasher or a clothes washer? Have you checked to make sure there is water flowing into the unit and someone has not shut off the valves to the water lines? ... Whirlpool Dishwashers

My pressure washer starts fine, shoots water OK. After running for 5-10 minutes cleaning siding I shut off machine. I go to start it again within a minute or two and the thing feels like it's just about seized. If i wait until the motor is completely cool, it will pull start freely and start right up. I think something is wrong with the pump, not the engine.


Your pressure washer may not have an ez-start valve installed from the factory. Without the ezstart valve, you will need to hold the trigger on the wand open to release the pressure to easily start your engine. This link will show you wh ... Briggs & Stratton Pressure Washers

I have pldb998ac frigidaire dishwasher. The rinse light stays on, and it won't start. Last night it was pretty loud while running the dishwasher, smelled a bit like plastic, and today only the rinse light. The heating element seems to turn on as well when the door is closed. Help - any ideas?


... Frigidaire PLDB998A Built-in Dishwasher

It will not fill with clean water. It sounds like it is pumping water out. I can fill it with water by opening the door and it runs its normal cycle. What is wrong


There is a inlet valve that has a solinoid control to open if the solenoid does not work the default position is closed and the water cannot come in ... Dishwashers

My D3112 Asko dishwasher controls will not respond. There is a pump or motor running non-stop, even after I push the power off buton. The only way to make it stop is to unplug power cord. It is almost like it is stuck in the middle of a wash cycle program, but the water is not spraying inside nor is the heater or dryer cycle appear to be on.


... Asko D3112SS Stainless Steel Dishwasher

I have a kitchenaid dishwasher, SS, model # KUDIO1ILBL6. When you press the ''normal'' button to run it, nothing happens. Tried other cycles and same thing, the green light goes on above the cycle but its just not starting. I tried resetting by opening, pressing high temp scrub then energy saver dry, high temp scrub, energy save dry, then close and hit cancel. Is there any other combo to reset it? or does it sound like something else is wrong? thanks!


... KitchenAid Dishwashers

Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the dishwasher but it's like there is no pressure behind it to force it through the holes in the propellers so it's just kind of dumping water out as opposed to having any forced pressure. Hope this makes se


Try adding some more water to the machine after it has done the fill cycle do not over fill it. if there is no change in the performance the you need to replace the main wash motor.\015\012if there is achange the you need to change the fill val ... Dishwashers

Kenmore Dishwasher My dishwasher fills with water and then stops. I hear the cycle timer continue all the way through the cycle. I pulled the screen off the bottom inside of the dishwaher and stuck my hand in the diswasher drain. Originally I felt and cleared what appeared to be a torn up rubber band. I feel a thin straight metal pin that I can rotate and I believe it causes the pump to rotate as well. Once I do that the dishwasher will run normally thorough a complete cycle...BUT I have to


If you have either dry bearings in the motor or sticky grease buildup in the pump bearing/seal, it can cause the motor to stick rather than rotate on startup. More likely to be greasy crud buildup. \015\012\015\012The best you can do without disasse ... Kenmore 24 in. 15149 Built-in Dishwasher

We have a Bosch SHE45M06UC/50 dishwasher that is acting a bit nutty, first of all the timers are all wrong, mostly too short for what the manual says except the quick cycle and it is too long. There is on some cycles a very long delay before it begins to fill and it seems to alternate between pumping and running randomly


Hi,\015\012\015\012The first thing to note with your make of D/W is the display only shows "estimated time" not actual time. There are just too many variables to give actual times, i.e. water temp. at inlet, drain hose length & diameter, as well as p ... Bosch Dishwashers

Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the dishwasher but it's like there is no pressure behind it to force it through the holes in the propellers so it's just kind of dumping water out as opposed to having any forced pressure. Hope this makes se


Water will flow out of your inlet pressure. The pump takes from your machine to spray. The same water is circulated during wash!Hence try the method I have informed you. If it is a micro controller problem you have to contact the service ... Dishwashers

I have GE GSD2300r00bb, it was working just fine the other day no unusual noise, today we tried to run it, just a little bit into the cycle, i heard a strange stalling noise that sound like the motor is stuck or something, i put a camera(in a ziplock bag) in the dishwasher to see if the blade is spinning, no spin, the water did squirt for about 1 sec then stop but still leaking out somewater. Is it the motor or the water pump. I just got this dishwasher about 1.5 yrs. Is this something i can fix


... GE GSD2300RBB Builtin Dishwasher

I have been running into alot of ge /hotpoint dishwasher with a little water near the pump screen the drain hose is tied up and the check valve in the bottom back appears to be good is that normal help please customers are saying they have never seen water in it before


Hi,This is a common problem. In most of the Hotpoint dishwashers, right at the back of the tube, there is a long screen. You need to take that off. You would see the piston and the nut -it's what is causing the problem.Tap the nibs to loo ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1231 seconds