Having problems with your Bosch SHU5315UC Dishwasher ?

Gets to the end of the cycle (1 minute left on countdown) and just keeps running, does not start the "dry" mode. will run until i open it and when i shut it it goes 13 minutes left on the countdown but then gets stuck at 1 minute again. does not drain. has been doing this awhile, but until now it would simply finish the cycle when i opened, closed and reset it. now it just gets stuck again.


Answers :

Hello,

Welcome to FixYa.

Based on your description
I'd say the issue actually with the control...unfortunately. The "1" being displayed is actually an error code associated with a heating fault.
\015\012Bosch has had a history of this exact problem I'm about to lay out for you and this is the first thing I'd be looking for if called out to service the unit with the symptoms you've described. \015\012 \015\012**B/S/H/ also issued a recall on certain models between 1999 - 2006 depending on the model & serial number, you can check with yours but you'll need the serial number too. The issue was directly related to the heating circuit (specifically the heat relay on the control) Here`s the link if you want to see for yourself **

http://microsites.boschappliances.com/safetyrecall/dishwasher/


As I've alluded to the issue is likely within the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ).

My first suggestion would be contacting Bosch re: the recall or calling in an authorized bosch service tech. if that is an option for you and your budget however, If you feel capable of checking this on your own, there`s a way to visually inspect the control yourself...it really isn't very complicated.

It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board.


dabfa62.jpg


The culprit will 99% of the times be one of the pins from the heater relay,

9f1823d.jpg

**Flip this over and inspect the solder joints, it will be obvious when you see it.**

This ones new, but it's where to look...

9119d99.jpg


...hence the unit sit`s and takes longer & longer to finish because it can`t heat to advance or unless the 2 buttons for "cancel" are pressed...or takes a long time as I mentioned and eventually display's "1" on units with a display and usually very poor cleaning as a result.

You can also run the unit through a regular or econo cycle ...any cycle with the exception of rinse & hold, and with the door panel removed place an ammeter on the gray/black wire it should draw 11 amps during the wash cycle...after it fills and the flow switch indicates it has adequate water to engage the heater.

i.e.

f57273b.jpg
**My Opinion - if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...but it has to be done well...or it will not last, although Bosch recommend`s replacing the control and I don`t pretend to speak on there behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)**

**Please disconnect the power or turn off the breaker before attempting any service to the dishwasher.**


If you do not feel comfortable attempting this service, call a local pro, preferably one familiar with Bosch/Thermador/Gaggenau/Siemens, to service your machine.

Hope this answer`s your question, let me know if I can assist you further.
Thank`s for visiting "FixYa" for your repair inquiries. Please take a moment and rate this solution to it's helpfulness.

Good luck.

Regards,

Macmarkus :)

I was having a similar issue. The cycle was taking too long and the sanitization button never turned on.

I just re-soldered the bad one as suggested above - on our Bosch SHE43C05UC and seems to have fixed the issue.

Thanks very much for posting this solution!
Repair Help & Product Troubleshooting for Bosch SHU5315UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Gets to the end of the cycle (1 minute left on countdown) and just keeps running, does not start the "dry" mode. will run until i open it and when i shut it it goes 13 minutes left on the countdown but then gets stuck at 1 minute again. does not drain. has been doing this awhile, but until now it would simply finish the cycle when i opened, closed and reset it. now it just gets stuck again.


Hello,Welcome to FixYa.Based on your description ... Bosch SHU5315UC Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

I have a Siemens SE24T250GB that will not complete the cycle, it gets stuck with one minute left on the timer. Any help will be gratefully recieved.


... Siemens 24 in. SE25T250 Free-Standing Dishwasher

Dishwater cycle gets stuck at 27 minutes and doesn't go beyond but continues to run, staying at 27 minutes. timing mechanism gets stuck in all cycles.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the cycle doesn't\015\012complete, then the first thing ... Dishwashers

Eurotech Model EDW254EWXX runs a 13 minutes cycle before washing like usual, but now it is getting stuck and not doing anything during that 13 minute cycle. No water is running, and it makes NO noise at all. We are not getting any errors displayed. I have unplugged it, and shut off the circuit breaker for 20 minutes, but the problem is still there.


... EuroTech 23 in. EDW254E Built-in Dishwasher

Kenmore dishwasher 665.17534202. something is wrong with either the timer or the motor. On a normal cycle it starts at 78 minutes and gets down to 48 minutes and it stays stuck at 48 minutes for appro


Http://www.allrepairmanuals.com/kenmore-dishwasher.htm?model_number=+665.17534202 ... Dishwashers

My Bosch SHU 3030 gets stuck during the washing cycle and will continue to run indefinately until the wash cycle knob is rotated a little bit, then it will work fine for a few more minutes until the knob gets stuck again. Whats my solution?


... Bosch Dishwashers

Dishwasher is not cleaning well, dirty film all over everything, like its not rinsing. In rinse cycle only, some water comes out of lower left port inside but nothing else. Hear a low buzz underneath unit like a motor or pump is energized but no water getting to the top.During normal wash cycle, buzz from underneath seems to cycle on and off, say every minute or so like its cycling on an overload. Do I have a bad pump and if so how do I get to it?


Hi. This may well be a pump issue, or an obstructed hose assembly, as well. Your symptoms are indicating that the impeller may be damaged. In order to pull the necessary schematics, I will need the entire model number. This ID tag will allow me to pu ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

Anyone have experience with a Fisher Paykel double draw dishwasher (model DD24) getting stuck in wash mode? Once it hits exactly 48 minutes it stays there. Only several hours later it cycles through OR you have to turn it off put it in rinse mode to complete. Already tried all the basics (unplugging, no fault codes, cycled through the diagnostics everything good and working). Did the quick diagnostic cycle of 14 minutes and everything cycled through fine. Next step will be to put the bottom cont


... Fisher and Paykel Dishwashers

Our GU2500XTPQ6 Gold quiet partner III begins a cleaning cycle but then different numbers appear on the minute countdown and the cycle never finishes. Once it gets to this point, you can only get it to drain. You cannot reset the cycle. We were once given a series of buttons to push to reset the control panel but don't know where it is. Can you help?


Yes call the manufacturer and ask for the code again ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

My dishwasher ALWAYS gets stuck at 82 minutes. It can be stuck there for as long as 30 minutes or more. It makes my full cycle time unreasonably long.


... Whirlpool Dishwashers

During wash cycle it gets stuck and won't move past the wash cycle. On a regular wash it is at 28minutes and when it is on a fast wash it is at 25 minutes. If I stop it and turn on the rinse cycle it will run through the 12minute rinse cycle with no problems. It is only the top dishwasher that does this, the bottom one is running just fine.


I've got the same problem with the bottom drawer on the DD605. No fault codes were set. I checked the heating element and it produced heat quickly. I suspect that the water temp sensor isn't satisfied, and the timer is waiting for the water to rea ... Fisher and Paykel DD605BK Dishwasher

DISHWASHERHD98E I stopped my dishwasher a minute before the cycle had finished. Now when i try to start it up again the 1 minute number comes up but gets stuck on this so that the 1 minute does not end (fan can be heard working) and I am unable to reset the programme. What can i do to overcome the problem.


You have probably flooded the base of the machine and it now is in flood mode take side panel off and have a look and drain water away common fault ... Hoover 24 in. HD98E Built-in Dishwasher

I have a Bosch dishwasher (SMI5072), bought in 2005 second-hand but working OK. It has always been a little slow to get going, and I had initially thought the clockwork program dial was getting stuck. Then I concluded that it had something to do with the filling up process, and I thought it must be because the water was rather cold and paid no more attention to it. This has meant that it seemingly takes ages to get through a cycle. Yesterday I put it on, left it and got on with some work. An h


There is a screen inside your water inlet valve that may be clogged. You will need to see if you are getting power to the water inlet valve when the machine calls for water. If you have power replace the water inlet valve ( not uncommon in older Bosc ... Dishwashers

Whirlpool gold dishwasher gets stuck at 53 minutes left for an hour


Try "resetting" the control board by running the diagnostic cycle. The cycle completes in 15 minutes. \015\012\015\012The details are in the service manual. The manual can be found hidden behind the tow plate (at the very bottom front of t ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

The dishwasher does not complete a cycle. It starts the cycle just fine but then it stops after one minute. It seems like it gets stuck and won't move to the next step. I do hear a slight clicking noise similar to a clock ticking, like its trying to move on, but then it stops. It clicks three times. When I open the door the "fine china" light is on even though I set it on "normal". Is there a "re-set" button?


The Control Board is gone, the part is $475.00 Find a new one.... ... Viking Designer Series DFUD041 (Premium) Built-in Dishwasher

My Kenmore Elite dishwasher doesn't proceed past the first few minutes of any cycle. It gets stuck at the "add a dish" part of the cycle and then stops and starts. It won't go further into t


... Kenmore Dishwashers

Hi my nearly 9yr old neff S5555XOGB/40 integrated dishwasher has problems on the control panel the program times come up with the completely the wrong times for the wash ie the 150 one comes up saying 32minutes on a quick wash it gets stuck at 1 minute left and keeps going on, also the delay timer timer is not working ( I have been told this could be a problem with the programmer) . Is it cost effective to get the progammer changed plus engineers cost or shall l look for a new dishwasher? Th


... Neff 24 in. S5543X2 Built-in Dishwasher

Hi my nearly 9yr old neff S5555 integrated dishwasher has problems on the control panel the program times come up with the completely the wrong times for the wash ie the 150 one comes up saying 32minutes on a quick wash it gets stuck at 1 minute left and keeps going on, also the delay timer timer is not working ( I have been told this could be a problem with the programmer) . Is it cost effective to get the progammer changed plus engineers cost or shall l look for a new dishwasher? Thanks Su


... Dishwashers

I have a whirlpool for Ikea dishwasher that is built in and I put it on the normal 30 minute cycle before I went to bed and 8 hours later it was still going. I opened the door and machine was full of suds. It is like it gets stuck and can't move on to the next part of the cycle. I have checked the filter in the bottom of the machine and checked the salt and rinse aid levels.


It could be waiting for the temperature to reach the required level.\012\012Sounds like the heater element has died. ... Whirlpool Dishwashers

Dishwasher Whirlpool ADG7540. Does not complete cycle. Approx 20 minutes into cycle dishwasher appears to get stuck on rinse.The water is cold. Machine stops and makes a constant beeping noise and the green light flashes 3 times repeatedly.


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

I have an SHU 4322. It displays "2H" in the countdown window. It will drain-cancel properly, but all of the programs display "2H" instead of the normal # of minutes for each cycle. How do I get the wash cycle to start normally?


Just reset the unit by unplugging the cord from the wall for 4 hours. The purposed for this is to drained the current stored in memory IC . So it will works normal again. Plug it again after 4 hours to see the result..Good luck: ... Bosch 24 in. SHU43 Built-in Dishwasher

Model she44c02uc; 2 years old. no matter which cycle we pick, it just keeps on running..it gets down to about 15 minutes on the countdown timer, and then resets itself to 80 minutes or so and washes over again...if we manually turn it off and then push quick wash, it seems to finish, but doesn't dry the dishes.......we have tried all suggestions in the manual and cleaned both filters; the line is not clogged...the sink and disposal both work fine. thanks


Hi,gibpru,ngafm at your service,You said, no matter which cycle you pick, it just keeps on running..it gets down\015\012to about 15 minutes on the countdown timer, and then resets itself to\015\01280 minutes or so and washes o ... Bosch Dishwashers

My Maytag Dishwasher mdbd880awq wont finish a wash cycle. It will wash and rise then when there is 32 minutes left it wont drain and wont dry the dishes, It just makes a clicking sound. I have to dry the dishes by hand and then use the rise only cycle to get the tub to drain. The drain only doesn't work either


... Dishwashers

Timer get stuck on normal cycle


I have had the same problem with my dishwasher 'soultion' make----- not knowing your type if you can try this - simply at the nob (if it has one) spray into it WD40 with nozzel, leave and repeat, this dose not harm elec.parts only improves the connec ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1532 seconds