Having problems with your Bosch SHU5316UC Dishwasher ?

When the washer gets to 1 in the cycle, it doesn't stop washing.

\015 In "Regular Wash" the cycle counts down from 84. It washes and drains down to 1 in the cycle counts. Once the cycle is at 1 it doesn't stop washing. In that last cycle it kept washing for two hours. I had to cancel to finish the wash. The dishes, however, are sparkling clean. The dishwashing soap was fully utilized. No drying ever took place.\015

Answers :

Try running the test cycle or running delicate economy in that cycle it gets up to 150 degrees in the very first cycle let it run 15 or 20 min see if the water is screaming hot it is not and Luke warm it is not heating it is most likely a control board heaters very rarely go out
Repair Help & Product Troubleshooting for Bosch SHU5316UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Bosch (SHU5302UC/U12). The washer often takes 2 or more hours to run. Sometimes it gets stuck for a long time part way through (e.g. just sits at "43"). Other times, it gets stuck at 1 and won't stop on its own. The latest thing is 2 dots have appeared on the display that I've never seen before. For example, instead of "43", it reads "4.3." Eventually it gets to "C.L." but does not stop running. Also, its been making very strange noises during part of the wash cycle.


... Bosch 24 in. SHU43 Built-in Dishwasher

When the washer gets to 1 in the cycle, it doesn't stop washing.


Try running the test cycle or running delicate economy in that cycle it gets up to 150 degrees in the very first cycle let it run 15 or 20 min see if the water is screaming hot it is not and Luke warm it is not heating it is most likely a control boa ... Bosch SHU5316UC Dishwasher

I have a kitchenaid dishwasher model kuds24se with a problem. I MUST hit cancel before I hit start. Note that it doesn't matter how long it's been since the last cycle. It could be a few minutes or a day or more. I have to hit start to get a complete wash cycle. If I don't hit cancel, the washer goes through some sort of cycle and stops. It seems like a normal cycle but of course it is not because I don't hear any water and, upon completion, when I open the door there is heat but the soap dispen


... KitchenAid KUDS24SE Built-in Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

My kitchenaid dishwasher won't wash. The clean light blinks and if I can get it to cycle, it turns on to ''2 minutes'', during which 2 minutes it makes some washer-like sounds but doesn't clean, dry or spit out any water. Before this, I wash having trouble getting my dishes clean. I wash able to get the bottom rack clean using the heavy duty cycle, but the top rack still didn't clean


... KitchenAid Dishwashers

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

My dishwasher is a Fridigdaire FDB510LCS1, approximately five years old. The timer/knob stops advancing at about 7 o'clock, somewhere in the wash cycle. But the washer keeps running. I marked the place where it stops and, on additional tests, it stops in exactly the same place. I can advance the knob slightly past this location and the washer continues through to the end of the cycle.


Hi\015\012\015\012This is due to a faulty timer on your dishwasher. You would need to replace it to resolve this issue. You can buy the timer for your dishwasher from this link---\015\012\015\012 ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Stops mid-cycle I have a MDB7100AWB that has been working fine for the last 7 years. Now all of the sudden it will not complete a wash cycle in any mode (including auto clean). It consistantly stops at 85 on normal wash & at 65 on light wash and then clicks/buzzes about every 3 seconds, like it wants to continue - but never does. Any clues as to what to try? Is 7 years all I can expect to get?


Hi SaviorSound,\015\012\015\012I'm Harvey the Master Plumbr.\015\012\015\012Your question is: You have a MDB7100AWB that has been working fine for the last 7 years. Now all of the sudden it will not complete a wash cycle in a ... Maytag MDB7100AWB Dishwasher

Ge triton I got my GE triton about 2 years ago and it has worked fine since. For some reason, now, it won't stop running through the wash cycle. I can't get it to turn off. I push the reset button hoping it will stop and all it does is go to "sensing" then back to wash. I have to open it to get it to stop temporarily, but there is water sitting at the bottom of it. Any suggetions?


Turned the breaker off and then on again.....\015\012Works like a charm!!!\015\012Thanks ... GE 24 in. GSD6660GSS Built-in Dishwasher

Frigidaire FDB126RBS2 Washer stopped working mid-cycle. Then a few hours later began washing again. Ran a load a day for another week before it happened again. It ran and stopped at Light Wash, then a few hours later started again and stopped mid-way through the rinse cycle. It has no power now and will not start again.


Be very careful, it sounds like an electrical failure, were the machine has cut out to protect you and itself. You need an expert there and quickly. Water and electric are a bad mix and more house fires are caused by washers than most other appliance ... Dishwashers

During wash cycle it gets stuck and won't move past the wash cycle. On a regular wash it is at 28minutes and when it is on a fast wash it is at 25 minutes. If I stop it and turn on the rinse cycle it will run through the 12minute rinse cycle with no problems. It is only the top dishwasher that does this, the bottom one is running just fine.


I've got the same problem with the bottom drawer on the DD605. No fault codes were set. I checked the heating element and it produced heat quickly. I suspect that the water temp sensor isn't satisfied, and the timer is waiting for the water to rea ... Fisher and Paykel DD605BK Dishwasher

My dishwasher siemens se25a266gb purchased in 2003 will fill with water go through a wash cycle but does not pump out the water i have cleaned out the filters, checked the exit hose and all seems ok the only way to get the water out is bale out by hand. after this it will run through a wash cycle then stop and not pump out. how would i get to the pump and check it? any help appreicated regards Alan


\012Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

Pots/pan light blinks alternately with the normal wash button. Sometimes the cycle will start and then the lights come on. Once they start blinking, the cycle stops and I can't get it to start again. Unplugging it for a few days has worked a few times. But it just keeps getting more frequent. If it does start up, it heats fine and washes perfectly.


... Whirlpool DU1055XTSQ Built-in Dishwasher

Wash cycle Washer fills and drains ok. Wash cycle only- I hear motor hum but no water moves in the washer. Dishes don't get wet and no spray that I can see. Water level is above filter screen.


Check first that the filter located inside the machine (on bottom) is clean. In case it clean - The problem is with the pump. It could be a blockage between pump and the tub, or just a defective\015\012pump (The pump takes suction from the tub and fo ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

The dishwasher stops at the rinse cycle, does not drain and then the Quick Rinse button is the only cycle that will light up. Sometimes I can get the washer to choose a different cycle... but it is about every third day. And once the load gets to the rinse cycle, it starts all over again.


... Kenmore 13593 Stainless Steel Built-in Dishwasher

I have a Kitchenaid Dishwasher M/N KUDS25SHWHO. Had to replace the control board because the unit would not start. Installed the new board and the unit now operates, but not correctly. Once in awhile on the Normal cycle, it will get a third of the way through the cycle and just stop. Used to be, you could hit any of the Wash Selection buttons and than any of the Options butons and then hit the Start button to begin the cycle. Now, as soon as you hit one of the Wash Selection buttons, the un


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

Brand new dishwasher stops mid-way through wash cycle with soap spilled out all over the door. Can't seem to get past the wash cycle to finish the complete wash/dry cycle.


If there is no water in the bottom of machine, see if your water supply is turned off, or check for a loose wire on the water valve, lastly, check if the float is stuck in the up position. That is the overflow protector. If the machine 'thinks' the w ... KitchenAid Dishwashers

BF41 Dishwasher with a leak stuck in mid cycle Hi, I have a 'general domestic Appliance Ltd' BF41 (95+G709394) dishwasher which recently started leaking at the door. After replacing the seal the problem seemed to ease, then recently the problem started all over again and the leaking got worse. A couple of day ago I couldn't stop it leaking and now it's stuck in mid cycle and even though the water is washing inside the machine it never gets hot inside or finishes the cycle. Ive tried stopping and


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1714 seconds