Having problems with your Bosch SHU5316UC Dishwasher ?

Even after ensuring that really hot water is coming from the faucet and placing the unit on the Delicate/Econo setting we consistently get a 2 HR reading. We have also had it where the unit gets stuck on Cycle 1 and we have to reset to go to CL and clear the system of its waste water. Is this a mechanical issue or a circuit board issue.


Answers :

Did you discover the source of the 2HR reading? Mine's doing the same thing, except the drain pump keeps running and running as well...
\015\012Any ideas?
\015\012I can't imagine it's anything but the circuit board (for the third time in ten years)
This is common, a lot of bosch dishwashers had circuit board recalls. call bosch to see if yours is one. also if you get the cicuit board replaced, ensure that it is programed correctly when it is installed. main reason dishwasher extent time is to heat to a certain temp. bosch will then average out previous cycles and adjust its times. sounds like your not heating.
Repair Help & Product Troubleshooting for Bosch SHU5316UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Even after ensuring that really hot water is coming from the faucet and placing the unit on the Delicate/Econo setting we consistently get a 2 HR reading. We have also had it where the unit gets stuck on Cycle 1 and we have to reset to go to CL and clear the system of its waste water. Is this a mechanical issue or a circuit board issue.


Did you discover the source of the 2HR reading? Mine's doing the same thing, except the drain pump keeps running and running as well...\015\012Any ideas?\015\012I can't imagine it's anything but the circuit board (for the third time in t ... Bosch SHU5316UC Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

My miele diswasher seems to be stuck on rinse cycle and will not advance...keeps draining and refilling. Can't figure out how to reset and restart new cycle, to clear the snag. What's going on? I have cleaned all the filters in bottom of unit per operating manual. Wish I still had my GE, where you could reset the unit...no button to do that on this overpriced unit.


Sounds like a broken timer. If it's a rotary dial, they're not too bad to change.... ... Miele Slimline G832SCi Built-in Dishwasher

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Water drainage I have followed the manual instructions for clearing all appropriate filters on the intake and outflow side but the cycle does not complete and leaves a pool of water in the base. What next? I have the G568/858 Plus Incognito unit (thisis the closest part # to my actual unit--can't even find teh right # listed...), and aI m dealing with the sme issue. I have followed all of the recommended steps in cleaning the filters, traps, etc. There are no kinked hoses. The water drains to b


YOU NEED TO REMOVE THE LOWER SPRAY ARM AND REMOVE THE SHELL THAT IS COVERING THE PUMP AND FOOD SHREDDER ,HERE IS WHERE YOU LOOK FOR A CLOG. ... Miele 24 in. G892SCU Plus Built-in Dishwasher

I have a Bosch dishwasher that is about 4-6 years old (model SHU8805UC/U12). A few days ago I found clear water in the tub hours after the wash cycle had completed. I drained the tub by resetting the cycle as instructed in the user manual, but the tub gradually filled up with water again after several hours.. will replacing the inlet valve solve this issue?according to what I can tell for my model the water valve assembly (part No. AP3783031) is the part I need. How difficult and expensive


Just pulled mine out last night. You have a different model but it should be the same. Remove the bottom dress panel and detach your inlet hose from the water valve assembly (have a rag handy to catch a little water). Two torx screws on the front ... Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

The unit goes through its cycles but the top rack is not getting clean. The bottom spray wheel works, the middle and top spray arms are getting water but it seems not enough to make them rotate. The pump screens are clear and there seems to be enough water. Whats going on?


The problem is likely to be that the jets in the rotor arm are blocked.\012\012To check this, remove the arm (it is easy to do, as it is intended for the user to do this) and clean out all the holes. Try running water from you tap through ... Dishwashers

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

Bosch SHU4302 WITH REPAIRED PC BOARD has been working fine for several years now seems stuck in rinse/drain mode and is not quite pumping cabinet dry. I have removed the screens and located the small impeller at bottom below cover. The impeller rotates as though it has multiple spring loaded stop positions. When I turn on the unit and open the door water is trickling from the sprayer arms at low pressure. It seems stuck in rinse mode and will not advance cycles or reset when shut off.


... Bosch Dishwashers

I tried the steps listed at this website for the same issue I am having. http://www.fixya.com/support/t273954-kenmore_elite_dishwasher The steps worked to get the dishwasher to "reset" with all the lights coming on. The problem I am having now is that after the "reset" the dishwasher starts to run a small cycle for about 5 minutes. Upon opening the washer, nothing has happened inside (no water, no visible movement of parts, no soap container opening). Upon closing the dishwasher and trying


I think think the water fill is ok and the drain is ok as it uses a seperate drain motor . but what is not working is the main wash motor . so no water is moving and the wash arms are not going around and the lights ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Model 3250 leaks tons of water SPORADICALY Checked the filter trap-clear>seems to get "out of cycle" Cleared filter a while back thought I may of brought up 1 0f 4 impeller blades! Possible? Is there a "trick" holding down on/off and start buttons to reset this thing? Help! Need a rowboat!


Sounds like your pump took early retirement. nope..no tricks..just sounds like your washer needs some major surgery in the pump area. ... Asko Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

My Bosh Diswasher model SHE44C02UC gets stuck on rinse at the end of any cycle with 1 min showing on the timer and wont clear? The water does not drain. I need Help


Module or drain pump need ed call 1-888-nyc-1055 they are pretty good with any bosch appliances. ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

We used our LG diswasher to clean our grill grates, which was a bad idea, because now the unit will not clean the dishes. We cleared the washer arms of debris, but the unit still is leaving the dishes on both racks dirty and is leaving the liquid soap dispensed into the unit undissolved on the door of the unit. There are no kinks in the water inlet, and water is getting into the unit, but the dishes are not getting cleaned.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please make sure the dishes are loaded properly or\015\012dishwasher is not overloaded. Also check that the dishwasher is filling\015\012properly. It will fill with water up to ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Dishwasher is not cleaning well, dirty film all over everything, like its not rinsing. In rinse cycle only, some water comes out of lower left port inside but nothing else. Hear a low buzz underneath unit like a motor or pump is energized but no water getting to the top.During normal wash cycle, buzz from underneath seems to cycle on and off, say every minute or so like its cycling on an overload. Do I have a bad pump and if so how do I get to it?


Hi. This may well be a pump issue, or an obstructed hose assembly, as well. Your symptoms are indicating that the impeller may be damaged. In order to pull the necessary schematics, I will need the entire model number. This ID tag will allow me to pu ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

I have an Electrolux EWDW6505G Dishwasher. Had started a cycle, then opened the door midcycle when water was in the tub -- and accidently pressed "cancel." When I try to start a new cycle now, I was getting an "Error 01" message. After trying to get out of it, I'm now getting a "water serv" message. How can I reset?


... Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

Gets to the end of the cycle (1 minute left on countdown) and just keeps running, does not start the "dry" mode. will run until i open it and when i shut it it goes 13 minutes left on the countdown but then gets stuck at 1 minute again. does not drain. has been doing this awhile, but until now it would simply finish the cycle when i opened, closed and reset it. now it just gets stuck again.


Hello,Welcome to FixYa.Based on your description ... Bosch SHU5315UC Dishwasher

Just installed bosch SHE68E15UC dishwasher today and during first cycle E15 error came up and unit will not go into another cycle or allow me to program anything else - sanitize and rinse aid lights are blinking - water went into the machine and it started filling the bottom and wasnt draining - i then adjusted the filter and the water drained - but e15 error persists - what should i do - is it install issue or machine issue - please help- thank you so much


... Dishwashers

Dishwasher drain is hooked to a food disposer and until recently the unit worked fine. Last week following a cycle a couple of inches of water did not drain out. All food is removed from dishes, silverware, etc. prior to loading and the food trap in the bottom is completely clear. I ran the unit empty through a Lightwash cycle and afterwards the water level (that which didn't drain out) looked to be the same as before. The dishwasher is run 2-3 times weekly whereas the food disposal is


Hi, The I don't think the problem is with the loop and the 32" above the floor.If the dish washer was removed from one house to another, did *********** ever have a dish washer in the house before that he replaced this one with? The reason I am aski ... Dishwashers

HI our Indesit IDE 750 dishwasher gets stuck on the first cycle and the timer doesn't count down. Switching it off and restarting drains the water, but it gets stuck at the same point in the cycle


This sounds like a heating element issue, If the water doesn't get warm it just keeps trying to heat but won't advance past this point until it has reached a set temperature. You dishwasher may or may not be fitted with a thermal overload that may ha ... Dishwashers

Frigidare dishwasher model gld355rfb2 when you select a wash cycle unit begins prewash when it moves to wash unit quits and pf (power failure )is on display unit is full of water on bottom of unit so I reset the unit hit cancel button at which time unit pumps off water . I then tried again with same results as above.


... General Electric GDWT160RSS 24 in Builtin Dishwasher

When starting wash cycle the dishwasher cda cw447 doesnt appear to be getting enough water in and is making a droning / whirring / electrical ? noise. pipes all connected ok inc aquastop water supply unit, no kinks etc. machine 3 1/2 yrs old, just started making this noise. appears to complete rapid cycle but still making unusual sound. water drains away fine from this cycle, dont believe pipes / hoses are blocked.


Try removing the inlet pipe, and refitting, might fix it, else likely that the \015\012Inlet water soleniod failing/failed or tiny mesh filter (it does come out for cleaning) behind the inlet hose clogged. Temporaily bypass the aquastop water s ... Dishwashers

Motor problem?? The dishwasher takes in water then the water just sits in the bottom of the unit until the end of the cycle, there is no water going through the jets so the dishes are not getting cleaned. You can hear the motor but nothing is actually happening until the end of the cycle when it just pumps the water back out again


Have you checked the pump / motor belt? ... Tecnik TDW2677 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2058 seconds