Having problems with your Bosch SHU5316UC Dishwasher ?

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed. Model #SHU5314UC/U06 FD#8001


Answers :

Test the door switch. It can be faulty or misaligned. You can also check the back of the unit and/or remove the rear panel and take a look at the thermal fuse. It may be bad not allowing enough current flow to operate the machine.

Hi,
\015\012


\015\012

The jumper plug must be there if it was on the old one. Also it is very important what kind of detergent did you use. Such dishwashers do not work with any kind of liquid or jell detergents and you have to use a rinse aid. Water enters the dishwasher via an electronic valve, also there is also a filter where the hose enters the valve, but as you have already disconnected the pipe connected to it you would have seen any obstruction. The valves are pretty cheap and pretty easy to replace, it usually consists of removing the lid and disconnecting a couple of wires with spade clips on them, undoing a couple of screws to remove the valve, then just replacing it and reconnecting the wires.
\015\012


\015\012

Do get back to us for any further query and do not forget to accept it.
\015\012


\015\012

Thanks for contacting fixya.com
\015\012

Repair Help & Product Troubleshooting for Bosch SHU5316UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed. Model #SHU5314UC/U06 FD#8001


Test the door switch. It can be faulty or misaligned. You can also check the back of the unit and/or remove the rear panel and take a look at the thermal fuse. It may be bad not allowing enough current flow to operate the machine. ... Bosch SHU5316UC Dishwasher

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed.


Do you have the manual?What is the exact model #?Thanks~! ... Dishwashers

We have a kitchenaid dishwasher, kudi22ot3, installed in 1992. It is not cleaning dishes even thought the tub is getting water, and we've run dishwasher magic through it a couple of times. The dishes will get clean for a few runs, and then will stop getting clean. Is it time for a new dishwasher or can this one be fixed? Thank you.


Hi,There are 6 major reasons that could affect the cleaning.A nice guide you could follow is :-http://www.partselect.com/dishwasher+dishes-not-clean+repair.htmOther than this, you need to check the pump. Make sure ... KitchenAid Dishwashers

I have a Bosch Dishwasher- I installed a new garbage disposal and forgot to knock out the drain plug (dumb-i know) and I ran the dishwasher that night- well in the morning I noticed it was full of water and the bottom and the drain was humming. I then realized what I had done- so I knocked out the plug and the dishwasher drained immediately. but now the drain continues to run - even with the door open and I cannot get it off the drain cycle. Any suggestions?


\015\012If you notice still any water in the base. you sponge out the water and then check turning ON the dishwasher. If still the same problem then two possibilities \015\0121) bad water fill value. ... Dishwashers

We just installed a new Kenmore Elite #13123K dishwasher. It has power and water but does not run. The lights light up and all but it does not seem to be getting any water.


Is the water inlet valve open? ... Kenmore 24 in. 15173 Stainless Steel Built-in Dishwasher

Dishwasher I am getting a run around with getting my LG dishwasher fixed properly. We had a tech more than once come in and look at our dishwasher. It has not been fixed and never dried the dishes properly. It is now leaking and going to a "del" level when we attempt to wash the dishes. It is also leaking on our fairly new tiled floor and under our new kitchen cabinet. Your tech stated the dishwasher was not installed properly. The installation dept , Francine stated it is not their problem


Not sure what you mean by a "del" level, but as far a drying issues:\015\012\015\012LG chose to use a very energy efficient drying method which relies on the residual heat of the dishes to help dry them rather than many manufacturer ... LG LDF6810 Built-in Dishwasher

We just installed a new kenmore dishwasher yesterday. Model 13242 It has been running for almost2 hours and is still on the washing cycle--no water in it however--is this normal? I'm in a bit of a panic as we are canning and I need the jars washed--we didn't get a manual with it as it was a floor model so I don't know how lon the normal cycle ids. HELP


THAT IS NOT NORMAL!!!!!!! A normal wash and dry cycle will take approx. 2 hours in length including drying cycle.\012You should see that water has been present in the machine within the first 2 minutes of the start of the wash cycle, you shou ... Kenmore Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

I have a brand new whirlpool DU1055XTV5 dishwasher, installed two days ago. After the cycle completes there is about 1/2" clean standing water left in the bottom. It is not just down in the well area, the whole bottom is covered with water. This is after running a normal cycle with no other options such as sanitize or heat dry. I called Lowes, the store that sold/installed it, and they said this is normal in new dishwashers to keep the parts wet. They said as long as the water does reach th


... Whirlpool DU1055XTS Built-in Dishwasher

I have a JennAire jdb1090aws dishwasher. It's about 4 years old. The symptom is no water flowing through dishwasher. Approx 3 months after installation, the same symptom occurred. Tech resolved with float switch adjustment (no charge). Has run fine every since. I have not checked water supply, but doubt this is the problem (new water heater 3 months ago, sediment gone). I suspect the float switch is bad or out of adjustment. How do I trouble shoot float switch in dishwasher? Connect ohm mete


Hi,The procedure to test the float switch :-http://www.partselect.com/dishwasher+test-float-switch+repair.htmMost for no water entering the dishwasher, there are 2 main causes. One is the float switch and the other ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

LG dishwasher I have just installed an LG dishwasher. When I try to run the dishwasher it sounds as if it is getting no water. I checked the water supply line twice, and nothing is blocking it. The line is attached to the hot water under the sink and is open.


I bought a stainless steel Lg less than 15 months ago for 800.00and it stopped working. The manufacture said so sorry even though you didn't take delivery until the end of Jan. your warranty goes by purchase date. I would of been better of with a may ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Have a GLD6500L00CC dishwasher. after the completion of any cycle there is a lot of water standing in bottom.It is understood that there should be a little water to keep the seal lubricated but the level is as high as the brackets supporting the heating element. The manual refers to running the discharge hose high referring to the installation instructions. The installer did not leave any install instructions only the Operating manual. There is no air gap installed. Where do you go to get a pa


The drain line may be partially clogged. You will find manuals here:http://www.geappliances.com/ ... GE Dishwashers

Broken dishwasher It started when my dishwasher flooded my kitchen. I drained it and turned it on, it was fine. then it happened again. I have drained it then when I went to turn it on again it just sounds like it is running with no water. If I put water into the bottom it will drain but it will not fill up. I bought this house 3 years ago I am unsure how old the dishwasher, do I need to get a new one?


I have a kenmore model 665 168 29000 the mounting bracket have broken from under the cabinet, so when you open the door and pull the racks out the machine moves forward, how can i fix this????? ... Bosch 23 in. SHU33A Built-In Dishwasher

Brand new dishwasher, installed last week. When it is done there is quite a lot of water standing in the bottom of the tub. It has only been run 2 times since installed and both times several inches of water were left standing. Is this something we could check or do I need to have the installer come back, which will probably take a week at least. Oh-KitchenAid #KUDC031VWH


First was a new garbage disposal also installed? There is a knockout on the garbage disposal where the drain hose connects to.\015\012If that is not the problem make sure it has the correct high loop or also called air gap. If that is not right ... KitchenAid KUDC03IVWH Builtin Dishwasher

I have a brand new Miele dishwasher which has worked grate since it was installed 2 weeks ago. It keeps shutting itself off & indicates an F13 fault. I looked in the manual, see that water is going in fine & pressure is good. It then says to clean water intake filter. How do I get to that ? I don't have a user maintenance manual. I'm on city water & doubt that the filter is clogged but My wife will kill me if I don't get it fixed today. Can anyone help. Glenn


On my Miele 1220 dishwasher, the inlet filter is inside the inlet hose connector, where it screws onto the water supply. To clean it:\015\012\015\0121. Turn off the stopcock.\015\0122. Unscrew the inlet hose.\015\0123. Remove the black rubber s ... Dishwashers

Asko diswasher Dishwasher will not get water. Lines all checked, water on. Pump runs even when in off. Problem started when there was a water clog in the sink next to the dishwasher, and the dishwasher backfilled with water. We used a shop vac to get the dirty water out. Next day tried to use dishwasher, runs, but no water and empying pump will not stop running. Ideas?


Check for water leaks or not draining/overfilling fault ... Asko D1776 Stainless Steel Built-in Dishwasher

We installed a brand new wdt710Pay dishwasher and water is not getting into the dishwasher. We know that the water system is working and there is enough wattage electrically. What could be another cause?


... Dishwashers

I removed an old dishwasher and replaced it with this GE 24" Profile GSD533ODO1WW unit. It seems to run through the cycles like it should but it doesn't seem to run any water for some reason. I hooked up a new water line to it and turned it on. There where no leaks that I could see. Is there any installation manual that you could send me to make sure that I didn't miss anything or is there anything that you can tell me that I should look for? Thanks, Jesse


... Dishwashers

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

I just installed a Kenmore Elite Dishwasher. The Dishwasher will not run and is not responding toany commands. I checked the powersource and water supply to the Dishwasher and everything is working fine. We are confused and need some help toget this dishwasher working. It is brand new and just out of the box.


If there is an assembly manual, check it! There are sometimes hold downs and protective strips placed on the machine at the factory to prevent tampering. There is probably one that is stopping the power from reaching the control panel. It may even ... KitchenAid KUDD03STSS Stainless Steel 23 in. Built-in Dishwasher

Ignis ADL347 integrated dishwasher runs for a few seconds then stops, beeps and light flashes 6 times. I'm told this is due to water not getting into the dishwasher. it was working perfectly until we had a washing machine installed, can't see any pipes that are twisted or crushed but also don't have great access to the back of the washing machine or dishwasher. I have no expertise whatsoever. What should I be checking/trying? Any advice appreciated.


... Dishwashers

I have a problem with a bosch dishwasher i put in a kitchen 10 years ago. knob on left side buttons on right , stainless steel interior. i dont think client has ever used it. he must have put in new disposal but did not clear knock out. he went to use it with regular dish liquid.it started to leak and foam. he left me a note to look at it. 10 hrs later its still running and water is everywhere. i disconect from disposal and pump water into bucket but now can not get water to go in to it. tried b


First check that the valve under the sink is turned on sorry have to put this part in next thing to check would be the inlet water valve and assure that you do have power going to the valve if you dont then you would look at the float switch as the p ... Bosch Dishwashers

Just installed a new Hot Point dishwasher.Mo #HDA2100N10WW. I AM HAVING PROBLEMS GETTING THE WATER TO DRAIN OUT. THE OLD MACHINE WOULD DRAIN FINE. IS IT POSSIBLE I FORGOT TO REMOVE SOMETHING ON NEW DISHWASHER?


Remove the drain hose from the sink and see if it will drain into a pail, if not then you have a problem with the machine that is covered under warranty ... Dishwashers

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

I just installed a new Whirlpool dishwasher (model DU1301XTV) and have run three loads. Each time, the glasses, silverware, and plastic, come out with white, chalky residue. There are also water spots. I have tried it with both Cascade detergent, and with a Quantum Finish tablet. I have also filled the reservoir with Jet Dry. Do I have a defective dishwasher? Do I have a clogged line?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the water\015\012temperature by using a thermometer inside the dishwasher to measure ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2477 seconds