Having problems with your Bosch SHU5316UC Dishwasher ?

Diswaher is stuck on drain. will not reset. power has been disconnected. will not reset


Answers :

Hello, \015\012 \015\012Welcome to FixYa. \015\012 \015\012Based on your description " diswaher is stuck on drain. will not reset. power has been disconnected. will not reset " it sounds like the emergency overfill switch has been actuated. \015\012 \015\012Here`s what to do and what to look for. \015\012 \015\012**Turn off the breaker/power at your homes service panel...safety first of course** \015\012 \015\012Remove the the bottom panel, referred to as a toe panel or kick-plate, essentially the lower service panel shown here...\015\012 \015\012dd2a40d.jpg\015\012 \015\012When you remove the outer toe panel, (typically black in color, though sometimes white depending on the model, customization etc.) there will be another small "L" shaped panel which is non finished steel, I find removing that allows much easier access as well.\015\012 \015\01227e2e22.jpg\015\012 \015\012 \015\012This panel can be somewhat more difficult as it secures the plastic channeling for the wires but if you observe closely you`ll see it does "snap" out of place...carefully.\015\012 \015\0128d2e98d.jpg\015\012 \015\012Once the panel has been removed check for any obvious signs of water in the base ( the unit has a plastic overfill basin with a float which will actuate an emergency overfill cycle, hence the drain pump runs & runs )\015\012 \015\012f5b8d76.jpg\015\012 \015\012If you don`t see any water in this area, direct your attention to the left in this basin/bottom ( from the front to be sure ) and you should see a device which will resemble a "stir stick" you`d use for coffee etc. it will be a red in color stick.\015\012 \015\012 \015\0125c066c9.jpg\015\012 \015\012 \015\012With the aid of a wooden spoon, long screwdriver, or if you can manage to reach by hand, lift it up and down gently and listen for a "click". \015\012 \015\012If there is no sign of water and you can here the "click" when lifting up and down the float actuater ( red stick ) then turn the machine back on and give it a try before reassembling the toe panel so you can observe for any possible leaks.\015\012 \015\012Let me know what you find. This is the most likely cause of the symptom you are describing so we can move forward if this doesn`t resolve the issue. \015\012 \015\012Thanks for choosing FixYa. \015\012 \015\012Good luck. \015\012 \015\012Regards, \015\012 \015\012Macmarkus :)
Repair Help & Product Troubleshooting for Bosch SHU5316UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Diswaher is stuck on drain. will not reset. power has been disconnected. will not reset


Hello, \015\012 \015\012Welcome to FixYa. \015\012 \015\012Based on your description " diswaher is stuck on drain. will not reset. power has been disconnected. will not reset " i ... Bosch SHU5316UC Dishwasher

My dishwasher Bosch shx43c05uc/40 seems to be stuck in drain mode and if I turn power off (or disconnect electric plug) and turn on again, it still stuck in drain mode.


... Bosch Integra 300 Series SHX43C0xUC Built-in Dishwasher

The panel is flashing rinse and clean and will not stop. the dishwasher will not drain now and will not respond to any touches on panel. We have disconnected power to see if it would reset.


I had the same issue and got it to reset.heated wash, normal washheated wash, normal washall lights came on, I hit cancel.Closed the doorrepeated aboveand it's back to normal.Hope that helps ... Maytag MDB5100A Dishwasher

How do I reset a Whirlpool Quiet Wash Plus 930 Series dishwasher after it stopped working? Filled up with water, didn't drain, I disconnected everything and reconnected, I have power but it won't start? Thanks


... Whirlpool 24 in. DU930QWD Built-in Dishwasher

My name is John, I have a Fisher&Paykel DD603 bought in Jan 08 and have a problem with the program selector, which is stuck on 12 min and will not progress to anything else. It seems that the arrow button does not respond. The eco button goes on and off by pushing the button. I disconnected the power, hoping for a reset of the logic board but had no luck with that attempt. Any advice available?


Hi\015\012\015\012The issue is with the control panel/key pad that is bad and it should be replaced. Hope this helps...please post back for further assistance.\015\012\015\012Daniel ... Fisher and Paykel Dishwashers

Our hot water supply to the kitchen sink became disconnected and flooded the kitchen. Since then it appears that we are not getting any water INTO the dishwaher (just makes a terrible grinding sound..solenoid stuck ?? ). I did put 3 or 4 quarts of water inand it drained alright. Also tried cancelling the cycles but that hasn't helped. We also discoonected the power for a day but still no luck. Please help Ron


... Bosch SHX55M02UC Built-in Dishwasher

How do i reset a fisher and paykel dishwasher model dw920. Code F1 appeard found out i had a blocked drain, fixed it but still beeps and flashes F1. Have also disconnected power from mains but still the same. Thanks David.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You\342\200\231ll need to reset it by p ... Dishwashers

My dishwasher (kleenmaid brandt super silent DW121TB) appears stuck in a wash cycle; how do I reset the program? I have read the instruction book to no available, tried unplugging power overnight, tried a combination of simultaneously holding buttons in and switching on, letting the machine run all night, drained the water and added clean unsudded water, and none have corrected the situation. There is also a selection lever inside the machine that is not identified in the instructions, it appea


When you say it is stuck in a wash cycle, do you mean the wash arms are continuously running?\015\012Is there water in the base when you open the door?\015\012\015\012Can you try to run the dishwasher in any other program like rinse ... Dishwashers

Powers on, fills up and will drain (on reset). Wont wash? Kind of like its stuck(?).


... Bosch 24 in. SHX33A05 Stainless Steel Built-in Dishwasher

Bosch D/W model # SHU9955UC. The drain motor will not stop running. Ran the reset sequence on the panel. Display reset to "0" minutes. Power cycled the D/W and when powered back on the drain motor started up again. What do I do ?


Hi ....This is a common problem. Remove the kick plate you will see the white base which also is a tray to collect leaks or backups. Reach your fingers over the top of tray and feel for water/wetness,if so safety switch has been activated and pump wi ... Bosch SHU9955UC Built-in Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Stuck in two minute drain cycle


Hi,It is possible that the unit has leaked.I want you to please check THIS link it will solve your problem.Don't forget to do the banging ... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Our Bosch dishwasher #SHU9922UC (FD8007) will not turn on properly. Only its drain pump starts -- and keeps running -- when it's powered on and the door's closed. Pressing the two "drain cancel" buttons for more than 3 seconds doesn't help. Neither does cutting off power, then turning it back on in the hopes of resetting the machine's 'computer'. No water inflow occurs. Help?


I had a similar issue after I replaced a bad drain pump, seems the logic got hung up.. I poured in a pitcher of water, closed the door, it drained and was then ok - worth a try. If not, you may have a bad water level switch. ... Dishwashers

It sounds like drain cycle is stuck. Is there some type of reset button? I tried unplugging the washer but when I plug it back in the drain cycle is stuck


Hello,Welcome to FixYa.Based on your description " It sounds like drain cycle is stuck. Is there some type of reset button? " , the good news...It is likely noth ... Asko D1796FI Built-in Dishwasher

The problem started with it not draining correctly and leaving water in the bottom - my husband took it apart and found a bolt in the drain. He removed it and now it won't start. It appears to not have power to the electrical panel- we have reset the breaker several times - left the breaker off for 10 minutes thinking it might erase the memory - I've asked for instructions to reset and I keep getting info that is very far removed from this model. I know it has a protocol because a repair


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012The reset on your dishwasher is as follows, ( I can't locate your particular model number...but its madw be whirlpool so there are only a couple of possible sequences ) however depending ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

LG dishwasher quit mid cycle. no power to the front panel. I drained the water and found a two pronged wire by the drain hose disconnected. reconnected it and I still get no power on the control panel


Here is the video for you its intresting to get it repaired V ... LG Dishwashers

GE GSD4920Z dishwasher. Problem is that it does not drain completely at the end of the cycle--about an inch of water remains. After checking for clogs, etc, we followed a troubleshooting procedure which involves a hard reset (power off, then reset twice at beginning of cycle) and this procedure successfully drains the tub. However the next time that it's used on a normal cycle, water remains again. Suggestions?


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa.\015\012Dishwasher not draining properly or not draining at all issues can arise due\015\012to different reasons. Usually, these issues are related to kinked hoses,\015\012knocked o ... GE 24 in. GSD4920Z Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

The unit is a Maytag model MDB5601AWW which it has recently began to lose power at the touch pad. The electrical breaker has been checked to confirm normal voltage. Additional investigation suggests that the unit can be reset by (1) disconnecting the power at the breaker, (2) disconnecting and reconnecting the ribbon cable that interfaces the touchpad with the control board. However, the problem reoccurs after a few normal wash cycles.


It sounds to me then that the display board or touchpad needs replacing,you havn't said that it's not doing it's cycles.so it's not causing any washing or cycle problems.i would replace the display board. ... Dishwashers

Bosch sgs43eo2gb dishwasher. wash programme completes, water drains out, but machine goes on draining, forever, stuck at around 50 minutes on the facia clock. there is no leak on the machine and everything else has been cleaned and operates perfectly. ie,fills correctly,heats correctly and drains fully but won"t stop draining & refill. Cancel programme and reset and it works perfectly until end of wash cycle again, when it continues to drain even with the door open. There is no leak in the machi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. Please once again check that the hoses are not kinked or drain pump and filter ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

There is gum stuck somewhere in my dishwasher drain line. The water won't go down. I took the inside apart and can see the hole where the drain water goes. I disconnected the drain hose under the sink. I got the water to drain out when there was alot in there, but now it won't drain again. I blew compressed air from a compressor backwards through the hose and it makes a big splash and bubbles inside the dishwasher, but the water still won't go down. I put Boiling hot water and vinager in there t


Ther e is noo easy fix, short of replacing the drain line( if indeed thats where the clog is)although you checked the hose from the under the sink, did you check with in the hole where the sink conection is made??and try disconnecting the drain hose ... Dishwashers

I have a Bosch Diswasher that is not draining. I have disconnected power for 35 minustes and used shop vac to excess water out of drain line. i also pulled all water thru the drain line from the tub itself. i assume that because i could pull the water, all baffles and lines are clear as i emptied the tub from drain line. you can hear the pump come on to drain water but no water is moving. What would be my next step. If it is to replace the pump, how do i easiest access the pump to remove and rep


Either the selector switch or pump is faulty. If there is not any clogs anyways. The system may need to be reset. Most resets are done by entering a series of numbers on the touch pad to enter diagnostic/test mode where the machine can be reset. This ... Dishwashers

Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?


Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Washer losing power. will reset if one disconnects


... Maytag 24 in. MDB5601AWS Stainless Steel Built-in Dishwasher

My Bosch SHE45M built-in dishwasher is suddenly taking an extra-long time to go through its cycles. On Regular wash it will countdown from 117 minutes to 31 minutes. When it hits that time it resets to 87 minutes, then counts down to 1 minute and will not stop. I have to hit the cancel-reset buttons for it to drain. I have tried to do a hard reset by cutting the power at the breaker for 20 minutes or more. I'm interested in potential parts and a description of how to fit it! Thanks in advance.


... Bosch SHE45M06UC Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1260 seconds