Having problems with your Bosch SHU9915UC Dishwasher ?

Wash doesn't go through its full cycle, then will not drain. or cycle keeps on going


Answers :

Hello, \015\012\015\012Welcome to FixYa. \015\012\015\012**What I`m about to share applies to All B/S/H/ dishwashers. That includes Bosch, Thermador, Gaggenau and Siemens.**\015\012\015\012\015\012Based on your description I know what the problem is, though you may not like it. I would still start by checking your water inlet temperature, the unit must be connected to a "hot" water supply line. Try running the hot water at your sink tap to insure the cold water is out of the lines just before you turn on the dishwasher. \015\012\015\012That is just a suggestion out of courtesy however...\015\012\015\012If it is what I suspect, the control, this won't make any difference but it's worth a try. If on the other hand the water is good and hot entering the machine, you likely have an issue with the control as I alluded to.\015\012\015\012The reason your dishwasher never completes a cycle is the control has detected a heating error. Here`s the most likely reason why it has detected the error...\015\012\015\012Even if your home water supply appears hot, it's not hot enough and must be heated by the dishwasher to insure a proper clean and dry. \015\012\015\012The issue with your dishwasher likely lye`s within`the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ). This is why it runs forever unless you "stop" it or by pressing the two buttons for "cancel".\015\012\015\012To repair your unit It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board. This will be one of the pins from the heater relay, hence the unit runs on and on ( because it can`t heat to advance or until canceled ) trying to heat the water.\015\012\015\012**Further to this, if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...although Bosch recommend`s replacing the control and I don`t pretend to speak on there behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)**\015\012\015\012**Please disconnect the power before attempting any service to the dishwasher. If you do not feel comfortable attempting this service, call a local pro, preferably one familiar with Bosch/Thermador/Gaggenau, to service your machine.**\015\012\015\012Hope this answer`s your question's, let me know if I can assist you further. Thank`s for visiting "fixya" for your repair inquiries. \015\012\015\012Please take a moment and rate this solution to it's helpfulness to you and leave a testimony if you're satisfied.\015\012\015\012Good luck.\015\012\015\012macmarkus :)
Bosch dishwashers from early this decade (around 2002) had an issue with motherboards going bad. I've replaced many Bosch built during that era. Try killing the electric supply at the your breaker box overnight. Maybe, just maybe, this may reset the computer.

Hope this helps.
Repair Help & Product Troubleshooting for Bosch SHU9915UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Wash doesn't go through its full cycle, then will not drain. or cycle keeps on going


Hello, \015\012\015\012Welcome to FixYa. \015\012\015\012**What I`m about to share applies to All B/S/H/ dishwashers. That includes Bosch, Thermador, Gaggenau and Siemens.**\015\012\015\012\015\012Based on your description I know what the problem is, ... Bosch SHU9915UC Dishwasher

Wash Cycle The wash cycle will not stop. It just keeps on going without moving to the drain and dry cycles.


Pot and pans takes like an hour to wash other than that it is probably a malfunction in front panel board or curcuit board in side door. ... Kenmore 24 in. 16032 Built-in Dishwasher

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

Hi, The timer lights up on the door when wash cycle is pressed --inside fills with water but after a minute no action -it won't keep going and the timer freezes but does not shut off the drain button won't activate but drain hose is clear? Thanks


Sounds like the touch panel/ before replacing it ch the ribon connections . where it plugs into the pc control . use a ereaser to clean and replug . . . also make sure the door inter lock is working properly .. mm ... Maytag MDB9600A Jetclean II Built-in Dishwasher

I wash it on the normal cycle and it wont stop until i press the cancel/drain button, then when it drains, it will start over on the normal cycle and keep going unless i just open the door.


The problem is that the timer switch gone bad. This switch is responsible in starting and stopping the machine to operate.If the washer is still under the warranty, take advantage of it and have it repaired by the manufacturer's tech. ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My dishwasher skips the final drain cycle. The lines are all clean and there is no clog. It drains just fine in the beginning of the wash cycle. Every time I do a load of dishes I have to run the full cycle, then leave the machine open for 3-4 hours and start the cycle again and listen for the drain at the beginning of the wash to drain the machine from the initial wash and stop the machine after it is done draining so it won't fill up again. Sometimes we have to unplug it and wait about an hour


... GE Nautilus 24" Built-in Dishwasher

Kenmore Ultra Wash Quiet Guard - will not drain at end of cycle. After cycle is complete, water (not clean) sits at the bottom of the washer but I still unload the dishes and then turn the cycle dial around again - going past all the water heating and filling and washing - and land on the drain cycle, it will drain. Any ideas why it will not drain when I let a cycle run, but will drain once I cycle it through to the drain option?


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

My dishwasher keeps washing, doesn,t go through the cycles, i have to push cancel and drain.


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa.\015\012Dishwasher not draining properly or not draining at all issues can arise due\015\012to different reasons. Usually, these issues are related to kinked hoses,\015\012knocked o ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Zanussi zsf2450 My dishwasher will not move from the wash to rinse cycle. Motor keeps going as if trying to empty the machine but water has already drained.


... Dishwashers

MY DISHWASHER SEEMS TO KEEP DRAINING THE WATER THAT IS IN THERE N THEN FILLS THE BOTTOM WITH WATER BUT WILL NOT WASH OR GO THROUGH THE CYCLES


... AEG 24 in. Favorit 40630 Free-Standing Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Dishwasher hums I have a 2003 Kenmore Elite Ultra Wash Dishwasher model #665.17469300. I started the wash today. The water came in the unit and started washing then I heard it stop and it just started making a humming noise. I was afraid it was going to overheat or something so I cancelled the washed and it drained out. I started the unit up on a different cycle and the water came in the unit but did not wash it just hummed so I cancelled and drained it again. I did that on all cycles and the sa


... Kenmore Dishwashers

The machine fills ,drains and washes as normal. However when it fills the wash temp is 60 as normal but the rinse temp wont go higher than 76 deg C . when the wash cycle is on , the cycle stays on wash not progressing thru drain and rinse What is the cause?


Hello. Let me assist you. There are only two reasons for your problem - if you can isolate your problem based upon these descriptors you will know which part to replace:\015\012\015\012\015\012\015\012\015\012\015\012\015\012Water-he ... Dishwashers

Noisy dishwasher my Kenmore quietguard 4 has developed an exceptionally loud hum/buzzing noise seemingly coming from the door of the dishwasher, when closed, locked and put on either drain or wash cycle.If the unit is allowed to sit for 1-2 days, the drain cycle will empty the tub without the buzzing noise starting. If anything else is attempted afterwards, like a wash cycle, the noise immediatley starts at a low level, then becomes steadily louder, until the full volume is reached, and does not


I have aloud buzzing nose and humming what is the problem ... Dishwashers

Bosch Dishwasher My 8 year old Bosch is not draining. It will not go past 1 minute on the rinse cycle, and 13 minutes on the regular cycle. For the past few weeks I have noticed a lot of bubbles in the bottom of the dishwasher after it is done, but it was draining. Now it's full of water and will not go past the 1 minute mark. I need to fix this, I can fix this, I just need some expert advise on how to do this myself. Thanks!


What is the model #?... there are 2 buttons when pushed together it will drain the water out..try the button to the left next to power scrub... and economy...hold the 2 buttons for 3 sec. you will hear you drain pump running.. if you don't hear any ... Bosch 24 in. SHU43 Built-in Dishwasher

My daughter put the wrong detergent in the dishwasher (!). Now its stuck in drain cycle. If I put it onto wash cycle I can hear it draining even with the door open, but when I shut the door it doesn't go to wash and the bottom fills up with water. Thanks!!!


Hi,You need to find the bottle of white vinegar or cooking oil, if you have one...that will cut the suds and get you working again...Check this out...http://www.acmehowto.com/howto/appliance/dishwasher/wrongsoap.ph ... Bosch Dishwashers

Our dishwasher (a Maytag - MDBH970AW) will not proceed past the intital intake of water. It has done this occasionally in the past, but with repeated attempts to start a wash cycle, it would eventually work and continue to work for some time afterward. However, in the past week, it will not go through a wash cycle. I have ran the water, prior to starting, to ensure that it is intaking very hot water. When it quits, I can push the start button again and it will go through the 2 minute drain c


... Maytag 24 in. MDBH970AW Built-in Dishwasher

Dishwasher Imperial KDI-18 will go through full cycle but water does not drain and starts another full cycle all over again, still without draining.


Have you checked for blockages in the filter area at the base and the drain hose where it enters the kitchen drain.\015\012\015\012Not sure what you mean by starts another full cycle all over again. Do you hear the drain motor turning on? ... Dishwashers

I have a haier dishwasher model WQP12 AFM, I've replaced the wash pump motor and drain pump (they had been damaged with water after last repair person didn't put widget around drain hose which split and water accumulated on bottom). It well for about two weeks, then it would not go through it's cycle and I noted water not heating up. Have checked element with meter, thats fine, I replaced timersince it wasn't going through its cycle and that has not changed anything. Any suggustions?? Cheers


... Haier Dishwashers

Our whirlpool dishwasher will only go on the light wash, just or a short time and then shut off. the other cycles, heavy and pots and pans will not go on at all. when we press the light wash button, both the light wash and rince and drain light all go on, for just a short time, then shut off. help!!


The membrane or touch pad is bad. Most of the time you need to replace the whole control panel. Usually one of the buttons has failed causing this symptom. ... Dishwashers

Smeg sa 622 x. seems to go full cycle but not washing


... Smeg Dishwashers

FDB1050REM2 dosent go through wash cycle. it will fill drain dry etc. will not move the water to wash the dishes


... Frigidaire Dishwashers

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1702 seconds