Having problems with your Bosch SHU9915UC Dishwasher ?

My Bosch SHU9915UC dishwasher will not power on. Any advice would be much appreciated?


Answers :

Hello,

Welcome to FixYa.

\015\012
\015\012
\015\012
Based on your post " My Bosch SHU9915UC dishwasher will not power on " it may just be a loose/burnt connection in the dishwasher junction box or a severed wire in the door panel.

** I would start by first shutting off the breaker...safety first**

Then removing the kick plate ( access panel at the bottom )...

macmarkus_133.jpg

...and checking the wiring at the junction box for the dishwasher 120vac supply line.

Remove the murret's and visually inspect the wire for "resistance burn" and strip the wires back and install new fastener's if necessary to repair.

i.e.

60f6a31.jpg

This is actually quite common to find a wire connector come loose due to improper fastening and once the unit is in use for a while the connections heat & cool, become loose from normal operating vibrations and burn up from all the added heat caused by "resistance".

Typically this will manifest in just the manner you've described.
\015\012
\015\012If it looks OK there I'd remove the outer door panel ( careful the edges are sharp ) via the six #20 torx head screws...
\015\012
\015\012macmarkus_168.jpg
\015\012
\015\012
\015\012...check for a severed wire at the pivot point in the door, typically covered in a plastic casing as shown here..
\015\012.
\015\012
\015\012macmarkus_169.jpg

\015\012The small plastic blocks which may be present in the bottom corners of the door panel, i.e.
\015\012
\015\012macmarkus_170.jpg\015\012
\015\012...they can be a pain to re-install, but they do only go in one way, however it is ok to leave them out...their only purpose is to strengthen the structure.

Let me know what you find and I'll try to assist you further if necessary. Thank you for choosing FixYa today for your inquiry.

\015\012
Regards,

Macmarkus :)

Repair Help & Product Troubleshooting for Bosch SHU9915UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch SHU9915UC dishwasher will not power on. Any advice would be much appreciated?


Hello, ... Bosch SHU9915UC Dishwasher

Kitchen Aid Superba Selectra 21 Mod.: KUDS21SS1 MS S/N: FE 84757436 After whole house power outage, dishwasher began constant high pitch beep or whine. Machine controls unresponsive; display shows F. Cycling power has no effect {except noise stops and display goes off when powered down - of course). Any troubleshooting and parts availability advice would be greatly appreciated!


... KitchenAid Dishwashers

All of a sudden, my Kenmore dishwasher (Model 363.1411691) will not cycle. When I lock it shut and try to set it to wash, all I hear is a click--no motor running, no water sounds. As I advance the timer knob, I just get clicks where each cycle should begin. There is standing water in the bottom of the dishwasher which does not drain out. Any advice would be much appreciated, for sure.


Hi.The clicks are simply the relays in the timer board that try switching on. The control module is likely working.The cycle does not start because of a different problem.If no light is coming on, then ensure that wall socket ... Dishwashers

Smeg e2 error (water level tripped). Filter is clean and no rubbish below filter on inside of dishwasher. I have taken the front panel off but am not sure where the float device is located - I am wondering if it is just to the left of what looks like a solenoid. There is no water in the base of the unit in the front panel so would rule out any leaks. Reset program and turned off power at socket but still not using hot water. Possible PCB issue ? Any advice appreciated. Smeg DI612C Dishwasher.


... Dishwashers

Where can I get the instruction manual for a Bosch Classixx Dishwasher SGS53C12UK? I have bought a second hand dishwasher that has only been used for 6 months. The programme works fine but when I go to use it again - check water shows on the display. I have to tilt the machine back as water is stored at the base of the machine, surely this is not normal? It there a simple solution to this or alot of cost involved with a new part? Any help would be much appreciated. Thank you.


... Bosch Dishwashers

For a Bosch she44co7uc/36, the timer gets down to 1 minute, it keeps on running inside. Any advice would be much appreciated


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Check the water temperature by using a thermometer\015\012inside the dishwasher to measure the water temp. It should be as close to 1 ... Bosch Dishwashers

Have NEFF built-in dishwasher Typev S9WIF Enr - S5543X1GB/17: FD - 8203 670150. The problem is that the detergent tablets - FINISH ALL -IN - ONE Power Ball are not dissolving, although they have been "wetted". The water pressure is set to maximum, and the spray arms rotate freely. Live in the far north of Scotland so is not a hard water area. Any suggestings as to the cause would be much appreciated. Regards


Thanks for providing the full product code for your dishwasher. This helped identify its user manual very easily form the Neff website.\015\012\015\012Question - have you been using Finsh all-in-one power ball with this unit belore? ... Neff Dishwashers

I am trying to fit an outer door to my Neff compact built in dishwasher. I have the correct fixing kit, but it comes without instructions and I have been unable to source any. Any advice or guidance would be much appreciated. Richard Hine


See this videos:God bless you ... Dishwashers

Our GE Profile (Quiet Power 6) dishwasher is having trouble cleaning our dishes. The top shelf rarely gets cleaned and the bottom is questionable. It used to work fine. We always use Cascade powder detergent on a normal wash cycle. We have hard water. Any advice would be appreciated. I took apart the washer looking for an obstruction but none existed.


The obstruction can be external to the unit. Check the drain at EACH connection working backward from the sink connection all the way to the motor pump outlet hole. Do not forget to dis-assemble the Air-Gap (if installed) and to check the inside of ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Hello I am having problems with my dishwasher. Model BFDWC60ss. The detergent compartment doesnt doesnt empty after each wash so the dishes are still dirty after a heavy cycle. I have checked the filters and they seem ok. I would be grateful if you can give me some advice. Much appreciated Mary


... Dishwashers

Hello, have a hotpoint LFT114 dishwasher that doesn't seem to finish a program. After approx 30 mins any noise has ceased (indicating the program has finished) & upon opening the door, the washing tablet has not been taken, nothing seems clean inside & the POWER & ECO LED's flash rapidly. Any ideas would be much appreciated! Thanks, Karl


... Hotpoint-Ariston LFT 228A 23 in Builtin Dishwasher

I have a Bosch Dishwasher, Model Number SHX46L, Serial Number 860200524 that is no working properly. After running a cycle, it did not pump out all of the water, though the water is very clear, and the dishwasher does not display that there is any electricity going to it. I have verified the is 120 Volts AC at the appliance junction box. However the dishwasher will not turn on, and no lights will come on? Do you have any suggestions? I would appreciate it if you would let me know what you


... Bosch SHX46L1xUC Dishwasher

Whirlpool Dishwasher No Power: GU1200XT dishwasher thermal fuse in power up circuit blew & was replaced about two months ago. It has blown again. Both times it was after wash was finished but water was left in tub. Would appreciate suggestions on what may be causing the hi temp condition and how to verify.


I have a similar problem with my whirpool diswashre GU2500XTPB1. I check thermal fuse (on the board. It is OK (continuty). Right door switch _ OK, Left door switch _ weaker a bit). It still not work) I do not know what to check? ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Kenmore dishwasher Food particles left on dishes and inside of dishwasher. All functions appear to be working normally. Water pressure OK, drain OK, water temp OK, Etc. Operating dishwasher though a normal cycle without dishes solves the problem for one load, then back to problem. Dishwasher is about 5 yrs old and worked perfectly for 4 yrs. Any advice would be greatly appreciated. Bruce


... Kenmore 17822 Free-standing Dishwasher

The dishwasher trips the safety switch in the meterbox. whirlpool ADP 5000 made in germany (not on the drop down list) the 1st time was after a finished cycle and the power was off in the morning. the second time the power was on at the wall and when thw nob to select the cycle was turned, the power went off. any ideas would be really appreciated. julian


\015\012Please DO NOT touch this machine IF the power is ON. There is a possibility of shock. The reason, the ONLY reason, that the Breaker "Trips" is, if there is a, Phase fault to Earth/Neutral, in other words the CA ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a kitchen aid dishwasher model kuds01dlsp3. The unit has no power. A repairman found that the power to the unit was fine and then said we needed a new circuit board. The charge would be approx 270. When I look at prices the whole assembly unit cost 179. wouldn't replacing the electronic component be much cheaper?


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. First\015\012thing is to verify that power is available at the power board of the\015\012dishwasher. Open the power board cover and check if the breaker is tr ... Whirlpool Dishwashers

Kenmore dishwasher HI i saw your name on the website look like you know your stuff. My kenmore dishwasher model #587.1518 has a flashing washing light i've tried different button seq. but nothing.I 've turned off the power too that didn't help thank you so much for any advice you can give me


Lexi, sorry for not getting back with you, I had to fly to the other side of the country for a week. You may be right about the door switch. First do this, with the dial set to rinse, press and hold the heat dry and start/cancel buttons togeth ... Dishwashers

Our church has a Vulcan Autosan built in Dishwasher, comercial style. The cable broke that raises and lifts the door. Here is the model numbers found on our dishwasher. R-16 BTF 81-07-1828-H If you have any idea where we could get this cable and how to put it on, we would appreciate it very much. My name is Donna Woods and I will put in my email address. Thank You, Donna


Hi Donna.Unfortunately the model number did not return anything after been entered in the online search box.The model name of this machine should be Vulcan R-16 ELT.Here the contact for Vulcan Hart parts distributors, call the ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

My Kenmore Ultra Wash Dishwasher model 17731 stopped working mid wash I checked the power cord and it is fine but the unit doesn't seem to be getting power. Is there a fuse in this thing? Any advice would be welcome.


... Kenmore Dishwashers

Our 2 month old Frigidaire FGHD2433KF1 dishwasher is producing a very strong foul odor. It is not connected to a garbage disposal and we only see a small amount of water in the bottom of tub when the dishwasher is off. When I use the sanitize cycle, it seems that the smell is even more intense, not sure if that could be do to a small amount of steam escaping on the highest setting ? We have no idea what to check any suggestions would be much appreciated


Do you have it connected to an air gap? If not this can allow the water to drain back into the dishwasher and will sometimes have food particles in it making it stink. ... Dishwashers

Hi there, we have had our Bosch Loggixx Auto Option dishwasher for about 5 years now and we seem to have had endless issues with it. However, it now seems to have an error with the timer, which on any wash it seems to get to about 6 minutes and then jumps to 32 minutes and the contents are not being cleaned. Any advise that you would be able to provide would be greatly appreciated. Many thanks


There is way's to fix this problem, first check the amps that is going to the dishwasher, and them repplace the timer.\015\012\015\012can be a electrical problem that is keeps damaging the dishwasher. ... Bosch Dishwashers

Drain problems I have a Kenmore 665.17292992 portable dishwasher. I've changed the filter and the seals however it still does not want to drain. It will drain but extremely slowly and since it's on a timer, it only drains maybe 10% of the water out. My next step was/is going to be the Check Valve... but I am at a loss right now. I thought for sure it would be the filter. Any advice would be appreciated. Thanks, PM


This may not be the solution, but look for an air in-take somewhere on the top/back of the unit. It's probably covered by a stainless steel cover that can be taken off. Unscrew this cover and see if the air intake is blocked with lint. This is usua ... Dishwashers

Hello, My Frigidaire dishwasher model number FDB1250REC2 is not starting the wash cycle, instead, the washing light starts blinking continuously when I press start. I turned off the breaker to the dishwasher and tried to start a load again, same problem! I would really appreciate any help that you can give. Thanks so much!


... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Bosch SHX 46L Our dishwasher would complete a cycle everything good. Sometime after, it would spray and wet the dishes leaving water in the bottem of the washer. Now, the pump runs constantly when the washer is powered on and it will not start a wash cycle. Any ideas?


Http://www.computercrowd.com/Itm250480379703_60270_Bosch_Dishwasher_Service_Repair_Manual.aspx\015\012\015\01 ... Dishwashers

I have a Bosch SGV4313GB/13, when the dishwasher finishes we find that the dishes are not as clean as they use to be, we also noticed that door for the dishwasher powder is open and powder is still left in the slot. Any help would be appreciated. David


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2414 seconds