Having problems with your Bosch SHU9915UC Dishwasher ?

Bosch shu9915uc dishwasher when turned on sounds like drain pump is running but water will not enter dishwasher. When opened the pump sound stops. I did have a plumber over right before this occurred to replace kitchen sink faucet but he said he did not shut off valve to dishwasher and valve IS open.


Answers :

Hello,
\015\012
\015\012Welcome to FixYa.
\015\012
\015\012Based on your description "dishwasher when turned on sounds like drain pump is running but water will not enter dishwasher" , it sounds like the emergency overfill switch has been actuated. Here`s what to do and what to look for.
\015\012
\015\012 **Turn off the breaker/power at your homes service panel...safety first of course**
\015\012
\015\012Remove the the bottom panel, referred to as a toe panel or kick-plate, essentially the lower service panel shown here...
\015\012
\015\012 dd2a40d.jpg
\015\012
\015\012When you remove the outer toe panel, there will be another small panel which is non finished steel, I find removing that allows much easier access as well.
\015\012
\015\012
\015\01227e2e22.jpg
\015\012
\015\012This panel can be somewhat more difficult as it secures the plastic channeling for the wires but if you observe closely you`ll see it does "snap" out of place...carefully.
\015\012
\015\012
\015\0128d2e98d.jpg
\015\012
\015\012Once the panel has been removed check for any obvious signs of water in the base ( the unit has a plastic overfill basin with a float which will actuate an emergency overfill cycle, hence the drain pump runs & runs )
\015\012
\015\012 f5b8d76.jpg
\015\012
\015\012If you don`t see any water in this area, direct your attention to the left in this basin/bottom ( from the front to be sure ) and you should see a device which will resemble a "stir stick" you`d use for coffee etc. it will be a red in color stick.
\015\012
\015\012
\015\0125c066c9.jpg
\015\012
\015\012With the aid of a wooden spoon, long screwdriver, or if you can manage to reach by hand, lift it up and down gently and listen for a "click".
\015\012
\015\012If there is no sign of water and you can here the "click" when lifting up and down the float actuater ( red stick ) then turn the machine back on and give it a try before reassembling the toe panel so you can observe for any possible leaks.
\015\012
\015\012Let me know what you find. This is the most likely cause of the symptom you are describing so we can move forward if this doesn`t resolve the issue.
\015\012
\015\012Thanks for choosing FixYa. Good luck.
\015\012
\015\012Regards,
\015\012
\015\012Macmarkus :)
Repair Help & Product Troubleshooting for Bosch SHU9915UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch shu9915uc dishwasher when turned on sounds like drain pump is running but water will not enter dishwasher. When opened the pump sound stops. I did have a plumber over right before this occurred to replace kitchen sink faucet but he said he did not shut off valve to dishwasher and valve IS open.


Hello, \015\012 \015\012Welcome to FixYa.\015\012 \015\012 ... Bosch SHU9915UC Dishwasher

Asko d3100 dishwasher still giving problems after replacing inlet valve. When you press the start button all of the lights come on and there is some pumping sound with a dribble of water coming through from the right hand side. When you take your finger off the start button everything stops, no lights, no pumping. Anyone got any ideas?


Hi.To start, disconnect power and ensure that there is no water in the tub when you restart the dishwasher.It looks like the overfill switch is preventing the machine from filling. The overfill (water level) switch is either a ... Dishwashers

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

Bosch dishwasher SHX46A05UC/40 is making noise when draining. I have cleaned the screen and hose back to the drain and removed all debris. So it seem to be the 'drain pump'. But replacing it - now that seem complex - is it? Looks like I would have to stand the DW on its head and remove the base and then replace the pump. Anyone know if I am on the right track? Could it be something else?


... Dishwashers

Hello, I just installed a GE profile dishwasher (pwd9280n00ss) into my kitchen. I connected a hose to the valve water inlet, I connected the drain tube from my garbage disposal to the check valve flapper and then the the drain pump asm. When the dishwasher finishes washing the dishes, all the water doesnt drain out. Any ideas how I can correct this?


... GE Dishwashers

My KUDD01DPPA KITCHEN AID DISHWASHER BOTH TOP AND BOTTOM DRAWERS have red lights on in the front and the pumps keep pumping . Is there a flood switch that needs replacing? im a plumber by trade. So im very capable of replacing any of the parts.


... KitchenAid 23 in. KUDD01DPPA Stainless Steel Dishwasher

Hey guys, I am a dishwasher repair guy in barbados, the caribbean. I am having problems with a Hobart LX30H. the relay board is doing half the things right and the othrs not at all. I replaced it with a new one and the same results. At startup, the wash sump heater and wash motor are running, but the fill valve, drain valve and rinse booster are not running. Hence the startup operation is stalled. the funny thing is that the rinse booster and fill valve led's on the relay board light up at


Not sure what sort of problems (fault codes etc) you were having before you chose to go on the path of replacing the relay board.\015\012\015\012It might help to know what fault codes you have been noticing.\015\012\015\012One ... Dishwashers

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Water leaks from underneath the unit. Water only leaks when the pump cuts on (pressurizes). It leaks down on to the hose connecting to the water inlet valve on the right hand side of the unit when looking at the door of the unit. When the unit is full of water and the motor / pump is not running the unit does not leak. This unit is a Maytag jetclean dishwasher Model DWU9200BAB about 12 years old


Please change the 'o'rings of drain line and the inlet and also check the drain hose and the inlet if there are any holes in it ... Dishwashers

Kenmore dishwasher will not fill with water model no 630.1609406. It will run a full cycle but not fill. Water was temp shut off to replace kitchen sink and now dishwasher won't fill with water. No fill valve that I can see cleaned filter but still no water.


First, are you sure that the machine is not filling?\015\012I go on calls all the time for this problem and it turns out than the machine fills but the wash motor does not run.This leaves soap in the bottom of the DW so it looks like it did not ... Dishwashers

We have installed a dishwasher (as of yesterday) and everything seems to work but it will not drain. this is a replacement for a kitchen-aid dishwasher that we have had for 17 years. Everything looks the same - it is supposed to pump through the garbage disposal. There is not an air gap but we did not have one with the old washer.


HELLO THERE PLEASE TRY THESE SOLUTIONS I HAVE PROVIDED i KNOW THERE IS NO AIR GAP BUT I HIGHLY RECOMMEND INSTALLING ONE TO HELP WITH THE DRAIN THIS WIL RELIEVE THE AIR THAT THE MACHINE PRODUCES further More \015\012\015\012 \015\012 ... Whirlpool Dishwashers

I am looking for a replacement chlorine supply tube that includes the anti-syphon (or backflow) ball valve to connect a clorox bottle to the pump inlet of a Hobart undercounter sanitizing dishwasher. In the set-up I have a large clorox bottle standing upright in the undersink cabinet and the supply tube comes out of the top of the bottle to connect to the clorine pump inlet


HelloPlease click on the following website link to locate the nearest dealer near your location to order the replacement chlorine supply tube. ... Hobart SR24C-4 Dishwasher

G.E. GSD5130 When the dishwasher is pumping out the water a small amount comes in the rotating sprayer head. At the end of the cycle the dishwasher still has water in the bottom. The amount of water varies from just a little to over an inch. I replaced the spring loaded check valve a couple of months earlier and everything worked fine until now. What should I check? Thankyou.


Mike, I just ran into the same problem. I found a second check valve located in the outlet hose of the ELECTRIC drain motor. This motor is located at the right rear underside of d/w and is used only for backflush of the filter. When the unit goes th ... GE GSD5130 Dishwasher

I have a GE DISHWASHER model #GSD2100R20BB. The motor/pump mechanism has been replaced with a brand new one from GE, The water valve and timer have been replaced with brand new ones from GE and the dishes on the top rack are still not getting clean, can someone point me in the right direction here; please?


Have you looked at the spray arm itself? sometimes over use the spray hole get clogged with debris, clean it and then check the return water filter for debris. clean the filter and check in the hole under it that feeds the pump. ... Hotpoint Dishwashers

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any error codes, New World sent a replacement PCB which made no difference except now have no error code. Circ pump, inlet valve, heater, drain pump checked independantly all worked.


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Dishwashers

ASKO 1595 daer greendude, indeed your troubleshooting was right!!!! i pulled out the dishwasher and the base was full of water. once i got water out, the fault sign went away and it's ready to run its normal cycle. now i need to figure out where the leak comes from: either the fitting or the valve itself. just in case i have to replace the valve: any good source to get it from? i live in california. once again, thank you much!!! i'll keep you posted on the developments


I live in australia our part no is 8052120 ... Asko D1776 Stainless Steel Built-in Dishwasher

My Maytag PDB3600AWX isn't working. The motor hums as if its working but no water is in the tub. I did put a pitcher of water in the tub to see if it would pump out and it does. I don't know what else to check for. We have had lots of problems with this dishwasher, its never washed the dishes well and has flooded my kitchen to the point of having to replace flooring. I thought its was because we had just had new flooring installed and when they put the dishwasher back in the counter the hose was


... Maytag PDB3600A Built-in Dishwasher

Hotpoint hda3440g02sa leaves a little water at the bottom of the dishwasher I have checked the check valve have even replaced I have put a high loop in the drain hose and still no help it leaves just a little water I hate to put a new pump because I have on this type of dishwasher before and still no help


Hi\015\012\015\012 \015\012\015\012When the dishwasher leaves just a little water and drains\015\012maximum then I would say that it is fine & the drain pump is also working\015\012fine. These units are designed in such a way tha ... Dishwashers

I need to replace the lifter in my dishwasher. I have the new part, but darned if I can figure out how it's attached to the pumphousing. I just need a diagram to show it connects to the drain valve lever and then to the pump housing. Maytag PDB2430AWE.


... Dishwashers

My dishwasher (Maytag MDBH965AWQ quiet series 300 was purchased in May 2006 (making it just a little over 4 years old). The handle broke on it initially and now the control panel has gone out including the start button. The cost of the replacement parts is right around $200, so I don't think it is worth investing that kind of money into it since it seems to be a lemon anyway. I have always been faithful to Maytag. At the time of our kitchen remodel in 2006, we chose all Maytag appliances. I


Well Kathy, you may be in luck. There has been a safety recall on your model of dishwasher and Maytag will give you a considerable allowance to replace with another Maytag. You may contact them at 1-800-544-5513 with your model and serial number and ... Maytag Dishwashers

I have a Kitchen aid dishwasher model#KUDP02CRBL2 and I replaced the drain pump and all it does now is drain very slowly i haveblown air through the drain line and removed all debri that was blocking the drain line cant figue out why it drains slow


... KitchenAid Dishwashers

Dishwasher leaks, not the valve, comming from underneith right side. looks like its comming from the sump. Pump seal??


There is a seal that goes around the sump that possibly has failed. The part number is 5304460995, however, you should check the screws that hold teh sump to the tub, as they may have come loose. If it's the pump seal leaking, the pump would need to ... Frigidaire FMB330RGB Built-in Dishwasher

Viking pro dishwasher wont start/pump h20. previously cleaned out chunks of rust from feeder hose at valve under sink then it worked. light works, pumps out h2o ok. hearing clicking sounds from cycl control knob. can this part be replaced?


It sounds like you still have junk coming into the supply line. Consider running a new hot water line to thie dishwasher starting near the hot water tank. And yes, of course, each of these parts can be replaced. Joe ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Frigidaire 24" FDB1050REB2 Dishwasher It will not allow water to come in. The pump works, the motor runs, but it will not fill up. Water valve has been replaced. Pleas help!!


Friend,ngfam1 At your service!You plain old need service ! I am not hands on from this side of the wire!How old is the appliance?If the appliance is 10 years old or more you may not be advisable to put good m ... Frigidaire Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2141 seconds