Having problems with your Bosch SHU9915UC Dishwasher ?

My bosch dishwasher will not stop running, plus the waster does not get hotM


Answers :

Hello,

Welcome to FixYa.

Based on your description
I'd say the issue actually with the control...unfortunately.


**B/S/H/ also issued a recall on certain models between 1999 - 2006 depending on the model & serial number, you can check with yours, though many not included here still suffers from the same problem...you'll need the serial number too. Here`s the link if you want to see for yourself **

http://microsites.boschappliances.com/safetyrecall/dishwasher/


As I've alluded to the issue is likely within the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ).

If you feel capable of checking this on your own, there`s a way to visually inspect the control yourself...it really isn't very complicated.

It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board.


dabfa62.jpg


The culprit will 99% of the times be one of the pins from the heater relay,

9f1823d.jpg

**Flip this over and inspect the solder joints, it will be obvious when you see it.**

This ones new, but it's where to look...

9119d99.jpg


...hence the unit sit`s and takes longer & longer to finish because it can`t heat to advance or unless the 2 buttons for "cancel" are pressed...or takes a long time as I mentioned and eventually display's "1" on units with a display and usually very poor cleaning and obviously no "extra" heat ( aside from the water inlet temp. ) as a result.

You can also run the unit through a regular or econo cycle ...any cycle with the exception of rinse & hold, and with the door panel removed place an ammeter on the gray/black wire it should draw 11 amps during the wash cycle...after it fills and the flow switch indicates it has adequate water to engage the heater.

i.e.

f57273b.jpg
**My Opinion - if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...but it has to be done well...or it will not last, although Bosch recommend`s replacing the control and I don`t pretend to speak on there behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)**

**Please disconnect the power or turn off the breaker before attempting any service to the dishwasher.**


If you do not feel comfortable attempting this service, call a local pro, preferably one familiar with Bosch/Thermador/Gaggenau/Siemens, to service your machine.

Hope this answer`s your question, let me know if I can assist you further.
Thank`s for visiting "FixYa" for your repair inquiries. Please take a moment and rate this solution to it's helpfulness.

Good luck.

Regards,

Macmarkus :)
Macmarkus is my hero -- the problem identification and solution were perfect. In case it is helpful to anyone, attached is a photograph of my board before I soldered it.
2_20_2013_7_34_33_pm.jpg
Repair Help & Product Troubleshooting for Bosch SHU9915UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bosch dishwasher will not stop running, plus the waster does not get hotM


Hello,Welcome to FixYa. ... Bosch SHU9915UC Dishwasher

Bosch Dishwasher Cycles will not stop running. They keep starting over. Help please!! Our 2 year old dishwasher will not stop running. It gets to the end of the cycle and starts over again. Plus, the cycles seem to have gotten longer. We called the Bosch repair number and they want $150 in cash to come out and look at it. Then they will come out and fix it!!!! Unbelievable!!!


Carry out a reset.\015\012This should reset the board back to factory settings,\015\012Deep Diver ... Bosch 24 in. SHU5305UC Built-in Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

Had a clogged garbage disposal, once fixed, the dishwasher stopped getting water to it, sounds like its running, but no water coming to the cycle, Its a bosch dishwasher, motor seems to run, drain working,but no water to it.


If you didn't do the disposal fix yourself then there's a possibility that whoever did it closed the water valve to the dishwasher although there is no good reason to do that...\015\012\015\012I would check the valve then make sure that a ... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch Dishwasher Dishwasher is about 6 years old. It recently stopped cleaning the top rack of dishes. It is getting water to the top propeller, but not with enough force to make it spin. I have checked the tubes running up top and they are not clogged. Could the pump be going bad?


Your filters need to be replaced. it's a 10 minutes work ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke


Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

Asko diswasher Dishwasher will not get water. Lines all checked, water on. Pump runs even when in off. Problem started when there was a water clog in the sink next to the dishwasher, and the dishwasher backfilled with water. We used a shop vac to get the dirty water out. Next day tried to use dishwasher, runs, but no water and empying pump will not stop running. Ideas?


Check for water leaks or not draining/overfilling fault ... Asko D1776 Stainless Steel Built-in Dishwasher

Bosch SHU9910 Dishwasher won't stop and drain. Does seem to be getting the dishes clean; just won't end the cycle; after 2 1/2 hours of constant running; open the door and manually shut it off but, of course, there is still water in the bottom. Suggestions?


... Bosch 23 in. SHU9910 Built-in Dishwasher

Bosch Logixx dishwasher gets stuck on either wash or final rinse programme and runs all night until stopped manually. heat, pump, water supply, arms led controls all working. Any ideas as to the fault


You have a bad control module. send me a 4 thumbs post if this was helpful to you.p.s im a old bosch tech ... Bosch 24 in. SGS09L12 Logixx Free-standing Dishwasher

Bosch dishwasher model SHU5316UC I stopped the washer in the middle, I cannot to get it to finish to the end. When I restarted, it would run forever. How can I reset and drain the left-over water in the machine? Please help!!! Kathy


... Bosch SHU5316UC Dishwasher

Bosch dishwasher It won;t stop the cycle it just gets running


Sounds like your control module has failed . module not allowing voltage to the heating element ... Bosch 23 in. SHU303 Built-in Dishwasher

WE HAVE A MAYTAG PLUS DISHWASHER ABOUT 3 YEARS OLD OR LESS. WE WERE GETTING READY TO WASH A LOAD OF DISHES AND THE LOCK BUTTON IS ON AND WILL NOT COME OFF, WE HAVE TRIED PUSHING THE DRAIN OFF BUTTON BUT IT WILL ONLY BLINK, WASHER WILL NOT RUN. LOCK BUTTON WILL BLINK 3 TIMES AND STOP WHAT DO WE DO?


Try holding down the drain button for about 5 seconds.If that still does not do it for you, try taking power from the machine to let it reset itself, easiest is to unplug the unit or flip the breaker switch for the section of the kitchen. ... Dishwashers

Bosch Dishwasher I have just moved into my flat where there is a Bosch dishwaher installed in the kitchen. I have tried on a number of times to get the dishwasher to start a programme but for some reason it fails to start. It does switch on but I dont know how to operate it. I dont have a manual for it so have not a clue what to press to get the programmes running. I would be grateful if you could help. Bosch Dishwasher logixx Model Number SGS6952GB/13 Installed 2001


Dear Saps,\015\012Go to https://portal.bsh-partner.com/portal(bD1kZSZjPTAwOQ==)/PORTALFRAME.HTM for a pdf download for an Intr ... Dishwashers

We have a kitchenaid dishwasher, kudi22ot3, installed in 1992. It is not cleaning dishes even thought the tub is getting water, and we've run dishwasher magic through it a couple of times. The dishes will get clean for a few runs, and then will stop getting clean. Is it time for a new dishwasher or can this one be fixed? Thank you.


Hi,There are 6 major reasons that could affect the cleaning.A nice guide you could follow is :-http://www.partselect.com/dishwasher+dishes-not-clean+repair.htmOther than this, you need to check the pump. Make sure ... KitchenAid Dishwashers

I have a Bosch (SHU5302UC/U12). The washer often takes 2 or more hours to run. Sometimes it gets stuck for a long time part way through (e.g. just sits at "43"). Other times, it gets stuck at 1 and won't stop on its own. The latest thing is 2 dots have appeared on the display that I've never seen before. For example, instead of "43", it reads "4.3." Eventually it gets to "C.L." but does not stop running. Also, its been making very strange noises during part of the wash cycle.


... Bosch 24 in. SHU43 Built-in Dishwasher

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed.


Do you have the manual?What is the exact model #?Thanks~! ... Dishwashers

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed. Model #SHU5314UC/U06 FD#8001


Test the door switch. It can be faulty or misaligned. You can also check the back of the unit and/or remove the rear panel and take a look at the thermal fuse. It may be bad not allowing enough current flow to operate the machine. ... Bosch SHU5316UC Dishwasher

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

Water seems to be leaking into the dishwasher at the end of the cycle the water appears to be clean, so I am wondering about a seal of some kind on the hot water line leaking or whatever. It is a Bosch Dishwasher SHU series 3200 My problem is the same. Water leaks in to bottom of dishwasher over about a 2-3 day period. The dishwasher runs fine. It does not ever run over. The water seems to stop entering the dishwasher after it reaches a certain level.


You have a bad water valve. When the unit is off, the valve should seal and the water should not flow. Something has gotten in the valve and is keeping the needle up or the diaphram in the valve has deteriorated. replace the water valve and you wil ... Dishwashers

My Bosch dishwasher, model SHX46A05UC/30 has been working fine. I ran it once today on the Power Scrub Plus cycle (always use this one). Shortly after unloading the dishwasher I needed to run it again with more dishes. Within a few minutes of running the dishwasher I heard loud, almost grinding noises. Nothing appears to be stuck. Any ideas on what to do? This dishwasher has always been quiet up until today.


... Bosch 24 in. SHX36L05UC Stainless Steel Built-in Dishwasher

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

I have a bosch dishwasher SHE43C06UC22 (non-LED version). It's stuck in the drain cycle and continues to run even when opening the door (it should stop, but it doesn't). As a test, I poured a large glass of water in the bottom of the dishwasher and it drained it into the sink as it should, but it continues to run in the drain mode with no water in it. I've heard I either have a float stuck or an emergency drain switch or leak somewhere causing the dishwasher to continue in the drain mode. Ho


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This can be caused by either faulty door switch or indeed the float you mentioned.\015\012\015\012This is where to look for the switch and test it ... Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Dishwasher not getting enough water in either drawer, although top drawer gets more. Dishwasher keeps beeping during cycle and reads not enough water and then stops running until you press the start button. Need Help, any ideas?


This sounds like a hard water deposit problem.Check your water inlet valve for a screen and see if its clogged. Also it may just be a water valve/solenoid problem. As in, it's too crusted up to float up and down.Some models have a water f ... Fisher and Paykel DD605FD Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2597 seconds