Having problems with your Bosch SHU9915UC Dishwasher ?

Bosch model SHU9915UC dish whasher water feed will not turn off. Need to know if control can be repaired or replaced? Part number, where can I order one, can I change it myself, I am handy.


Answers :

Hello,

Welcome to FixYa.

Based on your description, "water feed will not turn off"...the issue is not likely the control, but rather with the inlet/water valve.

\015\012
\015\012**To remedy this you will need to check and likely replace the valve**

This is what to look for..i.e.

e601791.jpg

As long as your model number is indeed correct, this info below will be accurate.

Original part is # 425458. It usually retails for about $20 - $30USD at places such as "searspartsdirect.com" "repairclinic.com" to name a couple, if needed. They may be available at your local brick & mortar parts depot/vendors.

**Before attempting to repair the unit please turn off the power and the water supply to the dishwasher...safety first**


If you remove the lower kick plate/toe panel, you will see the inlet valve to your left...


i.e.

7d9ad1d.jpg

Replacing it or to check for debris in the filter/screen at the inlet is pretty straight forward. Here`s how...

1) undo the water line. ( here you can visually inspect the screen in the valve...if nothing noted, you'll likely need to replace it as follows )

2) Remove the two #20 torx screws fastening it in place.

156e176.jpg

3) the feed tube to the machine at the back of the valve and swap it with the new one.

5937279.jpg
and

dd52c6a.jpg

\015\012
\015\012Once the new one is in or it's all clear you should be good to go.

Let me know if you need any further assistance, otherwise good luck.

Thanks for visiting FixYa.

Regards,


Macmarkus :)

Repair Help & Product Troubleshooting for Bosch SHU9915UC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch model SHU9915UC dish whasher water feed will not turn off. Need to know if control can be repaired or replaced? Part number, where can I order one, can I change it myself, I am handy.


Hello,Welcome to FixYa. ... Bosch SHU9915UC Dishwasher

Bosch repair tech's came to look at this dishwasher, he said the control module blew out and they need to order one, they also said it wouldn't be in until mid Decemeber. Is there one specific control module for this unit ?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

The slide on the upper basket keeps falling out. It's been fixed twice but doesn't hold. The second repair man who put the slide back in the rollers said he couldn't see anything wrong with it, but it still didn't hold, so he called your tech dept. who said they had roller and slide kits at a total cost of $66 for this model. The slide kit had a new part number but the tech department didn't tell the repair man why they'd changed the part. The roller kit was one for dishwashers the sides o


One option is installing stainless steel washers on the rack supports that screw into the side of the tub. The rack falls down because there is too much "slop" with the rack...a couple small washers to space them tighter normally does the trick. ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have model number KUD 101TJBL0. I have spent about 300.00 on repairs. It keeps blowing the thermal fuse. I have had it replaced sev. times. My repair man has given up on solving the problem. I did read on another website that you need to replace the wiring kit that comes with the fuse. Me service man never did that and when I asked him about it he said that is not the problem and would not replace it. So, before I just scrap my diswasher and but a new one I thought i would order another fuse k


Hi,This applies mainly to Kenmore Dishwashers with the model number\015\012665.15835791 but also to any Whirlpool or Kenmore dishwasher with an\015\012electronic display. There are several possible trouble makers on this\015\012dishwasher ... Dishwashers

I have a Whirlpool Quiet Partner 3. It sat up for a few months because the control panel went out and it took a while to save up and order a new one. Now it blew the thermal fuse. I put a 15amp automotive fuse in it to try it, and it runs until it fills up and blows the fuse again. I am trying to figure out how to test the motor and the heating element to see if they are shorted. My local repair shop told me that they want to replace my new panel with their panel first, and that after that


A 15amp automotive fuse is rated for a 12VDC system in an automobile, not a 125VAC houshold electrical system in an appliance. I don't think your automotive fuse can handle the start current being drawn by the main wash pump as the dishwasher starts ... Dishwashers

I have a siemens GV630 control pannel inside my Bosch Aquasensor Dishwasher Model number SGS5302AU/07 it has a blown electronic componet on the main electronic control pannel. There are four of these identical semi conductor components on this pannel one of them has exploded. The part number off the component is Z9MY748 this part needs to be replaced where can I purchase this part (I live in Acukland New Zealand) Yours Sincerely, Casper Vissers.


... Dishwashers

Kitchenaid KUDK03IT has just had it's second control board in 90 days stop working. New one is ordered, but I wonder why it is going through control boards.


... KitchenAid KUDK03ITBK Built-in Dishwasher

JennAir JDB1080AWS I have a jenn air jdb1080aws and the light console has gone out. The lights are very dim and you cannot change the cycle. If you press one button a different one lights up and very faintly. Also the timer does not light up anymore. If I replace the panel-con Part Number: AP4364294 would this fix the problem. Thanks


... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher

Hello I have a built in DCS dishwasher - width 24" heigh 35". It started smoking out the front and the repair man said it needs a new control board. Is that possible or should I buy a new one. IT is not a dishdrawer its a full dishwasher. the top rack is also broken. If I need to buy a new one - where from - new jersey area


Http://www.thefind.com/appliances/browse-dcs-single-dishwasheryou can purchase online from here... ... Dishwashers

I have a hobart LX18C. I purchased a new control board and as I found out its factory set to the h model. How do I change the board over to the c model. How do I program the machine for the different wash cycle times, I have one that is working but its on the 140s. cycle and only heats the water to 80 degrees. I see the push buttons on the control and wonder what they are for.


Here is a Hobart link that may help. https://feg.hobartcorp.com/resourcecenter/ProductDocumentation/F18615%20Rev%20I.PDF ... Hobart 24 in. LXIH-3 Built-in Dishwasher

I have a dishwasher that will not wash after I have pressed the start button. The product model number is 87371818S, serial number AUD 377371. I have been told that the sequence may need to be changed. Do you have an instruction manual I can follow or can you provide a solution before I call for an appliance repair person?


Hello & Welcome to FixYaFirst clean the drain filter pump assembly located inside the front bottom access panel. If the problem is still there after cleaning the drain filter assembly then it means the control board is ... Fisher and Paykel Dishwashers

ZANUSSI DA6141 Dishwasher Stops about 10min in, and it blows the fuse in the plug, open the door and water is hot, I change the fuse and set it on drain and it drains ok. I looked at the On/Off Switch it appeared to be discoloured so I ordered a new one changed it with no problem but the dishwasher stopped at exactly the same point (I know this as I marked the dial) Any help would be great thanks Nick


... Zanussi 24 in. DA6153 Free-standing Dishwasher

Hello, Our Fagor LFA-013SS Dishwasher hasn't worked in a few days. It stopped working when it beeped 3 times after doing a load. On the machine it says if it beeps 3 times it means there's no drainage. My husband and I tried to fix it but we're not handy! So we tried calling repair companies but so far no one can repair Fagor dishwashers...help! Thanks


... Fagor LFA013 SS 23 in Builtin Dishwasher

I have a double drawer dishwasher. On the upper one, the cycles jump to different settings merely by closing the drawer. On the botttom one, the setting is stuck at rinse and I can't change it(I tried cleaning the control) Any advice?


Sounds like you may have a bad unit control board with cold solder joints on it,and too you could have a high resistance ground and by merely bumping the machine you make and break these connections,check all chassis grounds and inspect the circuit b ... Fisher and Paykel Dishwashers

I have a Frigidaire Gallery (model #GLD4355RFS1) and the control board constantly flashes the error message. Do I need a new control board? Where can I order one and how do I install it myself?


... Dishwashers

I have a model 665.1576 or 1676 my paperwork does not have the number on it and no part number on he machine, but I ordered parts from the catalog which matched. about 7 years old, stopped draining, so I changed the Seal kit, pump base seal, impeller, plus drain cover gasket but not the pump gasket could not find it, reinstalled, pump works but much slower and times out, have to hit drain button to get all water out. Keith


... Kenmore Dishwashers

WHAT ARE THE THERMAL FUSE SPECIFICATIONS FOR KENMORE ELITE MODEL 66513122K701SERIAL NUMBER FY1211868 AND WHAT IS THE PART NUMBER FOR A THERMAL FUSE KIT? WE HAVE HAD TWO FUSES BLOW AND THERE DAMAGE TO THE WIRING ON THE LEFT HAND SIDE OF THE CONTROL PANEL THAT CONNECTS O THE SWITCH. THEIR IS DISCOLORATION ON THE PARTS AND WIRING. WE HAVE SEEN EXPERTS STATE THAT IN ORDER TO CORRECT OUR ISSUE WITH THE FUSE BURNING OUT WE NEED A THERMAL FUSE KIT AND WE NEED THE SWITCH AND THE WIRING THAT CONNECTS TO


Http://appliancejunk.com/ge/dishwasher/31-9137.pdf\015\012\015\012A ... Dishwashers

I changed the handel and switch assembly on my dishwasher because the old one was broke.The dishwasher does not turn on. It still doesn't work. it doesnt even light up. although one button does glow a little. Do you have any idea what it could be? the model number is MDBH955AWB


Check for line voltage at the door switches and from there to the control board thats to the right of the door latch switches for line voltage,if you have line voltages in all these areas then replace the front membrane push button control panel that ... Maytag MDB9600A Jetclean II Built-in Dishwasher

We are on the mainland but our dishwasher is on the island of Maui. We are told that the main control board is out. The dishwasher is only about 4 years old and is used only about 4 months out of the year. Is this a commmon problem with Bosch dishwashers? Is there only one "Main" control board? If so, do you know what the part number is? thank you.


... Bosch Evolution 800 SHE58C02UC 24 in. Built-in Dishwasher

I have a kenmore dishwasher number 665.13832k601 that will not cycle and the control panel lights come on in random order. When I push the smart wash button it will light up and the heated dry light w


... Dishwashers

'Dead' DU1100XTP The dishwasher will not start - no lights at all - no indication that anything's working (although I confirmed the unit has power). I've seen numerous posts regarding the control board - is there a problem with these in general? My unit is just beyond the warranty (naturally!) so I'd like to know if there's been any concession made by the manufacturer due to the number of problems. I'd gladly replace the board if Whirlpool would send me one. Thanks.


This may sound simple but... make sure its plugged in all the way. ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Maytag Dishwasher Model #MDB7600AWB One of four plastic WHEELs mounted by screws to a 10 inch metal bar located on either side of the top rack has broken where the wheel meets the screw shaft. (These wheels run along the guide tracks for the upper rack mounted on the inside of dishwasher.) Please provide me with a part number so I can order a replacement part. Thank you.


Call Maytag with information of the tag on machine ... Maytag Dishwashers

Cookworks wqp8-9239 slimline dishwasher. Start the cycle on setting 1-4 and half to three quarters of the way through it stops and starts beeping with the first 3 buttons of the control panel flashing. The manual says when lights begin to glimmer the machine is out of order? can i ficks this without sending for repair man?


... Dishwashers

Racks corroding. The dishwasher works great. Just had recall repair done. Problem is the racks are slowly corroding away and new ones cost as much as a new dishwasher. How do I find good used racks and what model racks are interchangeable? The actual model number is mdb9100aww, but it won/t let me enter the ww. Ted


Check on Ebay. I just entered this to check for you. maytag dishwasher racks" and there were several on there. One was universal and could be used with 40 different model numbers. ... Maytag MDB9100A Dishwasher

New SHE4AM16UC, professionally installed eight months ago. Worked fine with very light usage until now. Dishwasher starts normally but stops and signals "clean" after less than five minutes on any cycle. One inch of water in bottom that (I think) drains when a new cycle starts. Soap tablets are not ejected from compartment. Bosch authorized repairman says he now has two client dishwashers with identical symptoms and is asking Bosch support for ideas (he's changed pump, control unit, and float sw


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats.\015\012When the dishwasher doesn't sense a water t ... Bosch SHE4AM16UC 24 in. Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0664 seconds