Having problems with your Bosch SHU9925UC Built-in Dishwasher ?

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Answers :

Hi

Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dishwasher and remove the drain hose and check for any visible clogging. If still not visible then the drain filter or drain pump is clogged and you'll need to clean the drain filter and drain pump. To access the drain pump, please follow the procedure---
1. Drain pumps are mounted to sumps in the front of dishwashers --they're easily accessible from the front of dishwashers by removing toe kicks.
2. Tools needed: small flat blade screwdriver (for unlocking terminals).
3. Remove toe kick/base cover, pull up terminal cover and disconnect wires (using screwdriver to unlock locking terminals).
4. To remove pump, pull latch (on circular collar) & rotate pump clockwise (cw).
5. To install new pump, insert @ 2:00 position & rotate counterclockwise (ccw).
6. Clean water & debris from base, then check float operation.
7. Connect wires, then install base cover & toe kick.
Please note that dishwashers don't drain out the complete water such that heating element doesn't overheat. Hope this helps... If it does please do not forget to accept the solution or post back for assistance.

Daniel
Repair Help & Product Troubleshooting for Bosch SHU9925UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help


Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

GE Mod # GSD22360Z04WW will not drain water. I manually pushed the solenoid down and the pump and motor seemed to run. No water pumped out of the hose that was disconnected from the garbage disposer. I have discovered that the plug for the disposer was not taken out where the dishwasher hose attached. The dish washer stopped working after a new disposer was installed. I rotated the control knob and at no time did the solenoid for the pump operate. It went back to normal position after control kn


... Dishwashers

Kenmoore Quiet quard 3 Model #665.74363K1 Serial #FS3502091 The unit will not drain properly. When in drain mode, it will drain slowly when diconnected from the disposal and lowerd to floor, and drains even slower at disposal level, or hooked to disposal. Disposal nipple is clear. I removed the hose and flushed it out with high pressure, found no blockages, hose flows freely and did not fix the problem. The motor is turning and seems to pump water fine, all wands are truning with powerfull spray


... Kenmore Dishwashers

Same problem Hi, I have the same problem there is water in the filter basket of the dishdrawer, I have watched the draining process when itgoes to error F1 and there seems to be a cycle of draining then pushing the water back through again. I have checked for blockages as advised above with a wire, no blockage, I have also blown through the outlet hose to the drain and there is no blockage. I am thinking the blockage maybe in the contained section of the pump as the previous man has explained. T


Hi, \015\012Below is the service manual. Use the FU (fill water) function in the diagnostics and then use P2 to drain the water. Open the drawer and watch will testing.\015\012Good Luck\015\012 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a whirlpool gold model GU1500 diswasher. When the rinse cycle ends the water pumps out into the garbage disposal like it should, but then water backs-up from somewhere into the bottom of the dishwasher. The overfill protection drain seems OK...the water doesn't overflow. It doesn't have a air gap on the sink. The drain hose goes directly from the dishwasher to the inlet on the garbage disposal. It appears to be properly installed per the installation instructions. The washer is about 4 ye


Seems you answered your own question here. You need to make an air gap in the drain hose - take as much slack as possible and make a curve (upside down U) under you sink as high as you can go. Make sure you clip ot to back of the cabinet to stabili ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

GE Dishwasher model PDW8200J03BB stopped draining. Removed the drain pump, checked with Voltmeter and there is resistance on ohms X10 of about 3. The flap is in place so water isn't shooting back into the sump inlet. Replaced the sump inlet about 6 months ago because it was deteriorated due to hard water. Pump worked fine after that. Checked drain hoses and air gap. Was able to blow water through. Pump only trickles water out at air gap. Does the pump need replaced?


Clear the line from the air gap to the drain,, if the rest is clear the only thing it can be is the propellers on the pump, i which case you will need to change the pump ... GE 25 in. Profile PDW8200J Built-in Dishwasher

I have a Bosch Exxcel dishwasher which runs the drain pump constantly even with the door open and despite there being now water in the machine at the cycle wont start. I have checked the warer amtrix and the ffed hose to the sump for blockages. The float switch operates OK but when the water drains down the float drops and the water is pumped in, then the float rises and water leaks out and the drain pump kicks in again and no more ater will come in unless you push the float down. Inside the bas


I am not sure about this model but most models run a drain cycle for a set period at the start of a wash cycle and then move on to normal filling and cycle of machine provided the various switches are at the low level it will carry on to its set cycl ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

LDS4821WW loses water in wash and rinse cyle then gives E1 error. there are no leaks on the floor.The drain hose is looped high at the back of unit. so the unit is doubled looped first loop is at the side attached to the unit then the second is at the back of unit then to drain.


... LG LDS4821WW 24 in. Built-in Dishwasher

My GE Nautilus DW doesn't fully drain. When it is drained as much as it will it leaves water in the sump at the rear right. If you run the pump at that point, it sucks water out of the sump, but when you open the door and the pump stops water flows back into it. It seems like there is a check valve that isn't working. I have cleaned the sump and the screen which runs accross the rear. I also have taken the plunger out and cleaned it. Then I took the housing for the plugner off the bottom. I don'


HI. check the following areas for fualts.1. Air gap / Drain hosesIf there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: I ... Dishwashers

Bosch dishwasher SHX46A05UC/40 is making noise when draining. I have cleaned the screen and hose back to the drain and removed all debris. So it seem to be the 'drain pump'. But replacing it - now that seem complex - is it? Looks like I would have to stand the DW on its head and remove the base and then replace the pump. Anyone know if I am on the right track? Could it be something else?


... Dishwashers

Disposal plugged up and water backed up into dishwasher. Cleared disposal and dishwasher drain line. Checked around sump but dishwasher won't pump out. Sounds like pump is trying to run. I can blow air through the drain hose from the disposal and get bubbles in the water. Turned off breaker for 1 min. then tried reset. Can hear pump humming.


The pump is humming because its still trying to get all the water out of the unit. Deinstall the dishwasher and pull the entire dishwasher out from under your cabinet. Next step would be to disconnect the drain line from the drain pump and check to ... Dishwashers

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

What is function of valve in the drain hose? Prevent water from backing into the pump or slow the flow out of the pump?


... Whirlpool Dishwashers

Jenn-air dishwasher JDB-5 (jdb1105awb) will not drain. Have repeatedly prompted drain cycle (start/cancel twice) there is what seems to be a pump noise for a minute or two, but no water flow noise and water level is the same in the bottom. The manual is sparce on trouble shooting and schematics. I suspect something is clogging the drain path. No changes to the drain hose routing. Machine has been installed for three years with no major issues. What is the recommended disassembly sequen


... Jenn-Air JDB6510 Built-in Dishwasher

The unit fills up with water but the circulation pump wont turn on. if i jump the pump it works. the pump is connected to the timer board. is there any sensor that would cuase the timer board not to turn on the circulation pump. this unit seems to be manufactured by ASKO mod. DW20.3 i dont want to replace the board ($375.00) if not nessary. thank you


Hi\015\012\015\012\015\012Thanks for using FixYa. There is no sensor on your dishwasher for drainage purpose however, it uses a drain solenoid to open and close the dishwasher drain port. If this \015\012solenoid ... Dishwashers

There are two hoses coming from my Bosch SHE45M06UC dishwasher. One is obviously the drain coming from the back of the unit, and the other is attached to the side looped and not connected to anything. I went online to the Bosch website for a installation manual and it describes this hose as a air venting hose. Does the end attach anywhere or does it just hang loose on the unit. My husband detached it from its original position and thought it was part of the water line. HELP!


Many people realize the dishwasher connects to a little hose on the sink, it is called an air gap. However, many people wonder " The air gap is there to prevent the water from being siphoned out of the dishwasher. When water flows through the drain ... Bosch Dishwashers

Won't drain Hi my dishwasher will turn on start running but cannot drain the water i checked the drain hose it is totally clear. People have suggested its something stuck in the pump but I can't seem to access the pump


To access the pump, first bail and sponge out any water in the machine's tub. Then tip the machine over on its front, using a heavy blanket or pad to protect the washer's finish. Remove the back service panel. \015\012The pump is attached to the moto ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

GE TRITON XL NOT DRAINING-CHECKED AIR GAP AND HOSE TO DISPOSER. USED BASTER TO REMOVE LOTS OF WATER THAT SMELLED REALLY BAD ON ONE RINSE LIKE BACKING UP. CLEANED SCREEN AND AREA IN PUMP AFTER REMOVING IMPELLER (SP). WATER NOT EVEN COMING UP THROUGH DISPOSER. BAD PUMP?


... GE Tritonr XL GSD6260JCC Dishwasher

I have an Asko D3230 which has activated what is probably the overfilling protection and the pump continues to run. The overfill activated because we had to pull out the machine to get to something and when putting back in there was a kink in the hose. Then we ran a cycle and the water wouldn't drain out. There is now no kink and we have removed all the water we can find. It is now completely empty but the pump continues to run even when the dishwasher is switched off, e.g. the off switch an


... Dishwashers

Whirlpool DU915PWPTO wont drain leaving water in the bottom what does drain is slow, disposal clear,hose clear, pump runs to wash dishes,water in bottom is more than normal


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1446 seconds