Having problems with your Bosch SHX43P1 Builtin Dishwasher ?
Kitchen counter top hangs over the control panel and I can not reach the buttons
Repair Help & Product Troubleshooting for Bosch SHX43P1 Builtin Dishwasher
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Kitchen counter top hangs over the control panel and I can not reach the buttons
... Bosch SHX43P1 Builtin Dishwasher
My Asko dishwasher d3232xlfi has control buttons on the top of the door. How do I install my granite counter top? Do I cut it out so my fingers can easily use the controls?
Normally the controls can be set with the door open and upon closing the door activate the washer with the options that were chosen. Normally, you wouldn't see a cutout made for the washer controls. These are intended to be hidden when closed. Goo ... Asko D3232XLFI Dishwasher
On/off control button on top panel of door is
A service call is necessary.usually that button support from one side breaks and needs to be replaced.it is not a expensive fix. ... Dishwashers
Model #PLD4555RFC0 The control panel lights on the front are all flashing and start cancel button will not change anything. flashing Er with wash, dry, clean, and and S showing. Top controls have China/Crystal light flashing and Low rinse agent light flashing. Nothing seems to work
... Frigidaire Dishwashers
I have a DU1145XTP. The lock light button is on and can't get the dishwasher to start. I pulled the top panel and removed the cover on the switch and control panel.
\015\012To turn on Lock:\015\012Press and hold Heat Dry for at least 4 seconds. The Locked light\015\012glows. If you press any pad while your dishwasher is locked, the\015\012light flashes 3 times.\015\0 ... Whirlpool 24 in. DU1148XTP Built-in Dishwasher
Pld2560lcc1 Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.
Pulled the touch pad, go after the middle third with a very small screw driver, cleaned the flex circut with contact cleaner\015\012\015\012powered up fine seems to be working again ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher
PLD2560LCC1 Frigidaire Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.
... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher
The start button on KitchenAid model #kudp01flbl6 will not engage, although all of the other lights in the control panel light when pressed. The cancel button will turn off the other lights in the control panel as well. This diswasher is 5 yeras old and lightly used in a household of just 2 professional adults. I've had service come and he uncovered a "burned' conection in the electronic control assembly p/n 8564542, which looked to me to be P8. A new electronic control panel was installed
HI. I need you to clarify somethign for me. You mentioned that you have replaced the " electronic control panel". Are you reffering to the interface board or the actual plastci panel? I understand that the part number "8564542" in in reference to the ... Dishwashers
I have an AsKo D1996 super cleaning system dishwasher...the front panel with the control buttons on the top of the door has pulled off the front. I need to replace.
... Asko D1996SS Built-in Dishwasher
When I try to start the dishwasher, I can get the light to show I want it do do a normal load. Then when I hit the start button, it lights up but the machine will not sstart. Then in a few minutes the lights on the control panel at the top of the door go out. What can I do to fix this? The model # is KUDS011JBS0 tHE 0'S HAVE A SLASH ACROSS THEM THE TYPE IS 577-0 SUPERBA
Hi,\015\012\015\012Your control board has gone bad... you will need to replace it.\015\012The replacement is not very hard, just make sure that you mark where all of the wires go before removing them.\015\012\015\012Here ... KitchenAid Dishwashers
I have an Asko 1805 Dishwasher. I've looked at some of the other responses and have this sinking feeling after tonight's series of unfortunate events. Tonight, I pushed on the On/Off switch on the left and it appears to have broken. The dishwasher no longer turns on. If you push in and hold the button, the lights come on, but when you let go, they turn off. This appears to be Part 763255 on RepairClinic.com. I also need the overlay/decor insert across the top of the control panel which app
Hello Rick,\015\012 \015\012Welcome to FixYa.\015\012 \015\012The "very instructive, but poor resolution" info you've referred to in your post was indeed a previous solutio ... Asko 24 in. 1805 Built-in Dishwasher
Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than
... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher
Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che
I have a MDB6759AWS3 that is one year and two months old. This morning I went to the control panel to press the buttons and some would light up and others would not. I disassembled the inner panel and looked at the "computer like" flat ribbon that connects the control panel to the main circuit board and noticed that some of the wires in the flat ribbon had deteriorated. I put it back together and pressed the buttons and they flash very dimly for a few seconds and got the dishwasher working bu
You may want to check the warranty iif it is a maytag or whirlpool, some have a 5 year warranty on the control and board. If not you can go to www.searspartsdirect.com to l ... Dishwashers
The buttons on my control panel no longer work. At first, it was just one button, then two. Now none of the buttons work. The model is a Whirlpool Quiet Wash Plus #DU920PFGQ2. Do I just replace the control panel? The dishwasher is receiving power.
... Whirlpool Dishwashers
Hi, I have the Bosch Logixx Dishwasher . BOSCH SGS0922gb /06 .. aged about 6 years old .... When I press the on/off button 'on' the led display only shows the 'not started' message. When I press the on/off button 'off' the led display lights up momentarily with 'start' etc just before I have fully released the button. I have tried a new switch and the same happens so not that. ALSO i can sometimes see S1....> on the top panel and get the machine to show on the top panel the close door
Lock Control I don't have a manual for my dishwasher. The Lock button is on (top of dishwasher). I have pushed that top button for 3 seconds. The button on the top and the "L" then both blink. The button on the top then stays on and the "L" light goes off. Since I can't get the lock light to go off - - my dishwasher won't tun on. Thank you very much.
First try unplugging the washer from powerpoint for 30secs..this may disable lock.if not, some washers will still work on lock if you hold the buttons you need. for 5seconds. eg try starting washer as normal but hold the button for 5secs....(Ps you m ... Jenn-Air 24 in. JDB1050AW Free-standing Dishwasher
Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.
I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher
Maytag quiet series 200 model MD88750AWB Dishwasher doesn't work. Control panel only responds to the heavy wash button. When pressed it lights up along with three option lights. After about 10 seconds they go off. There is no mechanical response to the pushed button. There were no symptoms leading up to this problem. If you can give me a "head's up" about what to look for before I open up the control panel I would appreciate it. Thank You John
Hi\015\012\015\012\015\012\015\012\015\012\015\012If your dishwasher doesn't work at all, check these:\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is there power getting to the dishwasher? This can be difficu ... Dishwashers
The Start button does not light up, yet the left side did light up for wash cycles. I'm guessing the PC Control board has some issue with touch button panel, as a faint high pitched shrill can be heard from the board after I took the door off and put my ear to the board. Also, over time the left side of the panel stopped lighting up too, so I through the circuit breaker. Can you advise which component it is. I'm guessing the faint high pitched shrill is the PC COntrol board attempting to communi
You have a faulty touch pad that will need to be replaced. Below is a \015\012link to a video you will want to download so you can see how to replace \015\012the touch pad.\015\012\015\012\015\012\015\012 ... Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher
My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash
I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers
I have a whirlpool quiet partner i dishwasher (model DU1055XTSQ2) that has suddenly stopped working. Control panel has partial functionality. All of the buttons on the control panel have a green LED feedback light when depressed. None of them provide LED feedback anymore except the Hi-Temp Wash, Sani-Rinse, and Heated Dry buttons. So there is power to the dishwasher. Any ideas? Please help Scott
The control board has failed.CLICK HERE to see the parts breakdown. ... Whirlpool DU1055XTSQ Built-in Dishwasher
Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.
The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers
I have a Kenmore elite 13102 dishwasher touchpad that has begun to crack around the start button. Does this necessitate changing out the whole electronic control pad or is there a part that is the "overlay" to the control panel? The functions for each button on the panel work fine. LH
Hello,You will need to replace the touch pad assembly. You can purchase the part from the link below. ... Dishwashers
Zanussi zdt6053 in built dishwasher not starting. When pressing the control panel on/off button the 65 deg normal wash light comes on. When pressing the program selection button nothing happens. When closing the door the machine does not start up. Is there a fault in the control panel circuit board? Would water pressure prevent the machine from operating?
... Zanussi 23 in. ZDi6053SX Built-in Dishwasher