Having problems with your Bosch SHX46A07UC Built-in Dishwasher ?

My Bosch dishwasher is taking hours (at least 3 - maybe more) to complete a cycle. There is gummy, yucky stuff building up inside - sorta pinkish brownish. Could the water not be hot enough? A couple of months ago we installed an on-demand hot water heater and I wonder if that could have anythig to do with it. I've tried running the hot water in the sink first but that doesn't help. Any ideas


Answers :

If your on demand heater is one of the small ones that mounts under the sink, it will not flow enough water to fill your dishwasher. the dishwasher is waiting for the water level to fill before it starts washing. your bosch will heat its own water. hook it up to a cold line ahead of the water heater so that the fill valve is fed with full pressure. the residue sounds like detergent build up. when you get the water issue resolved, run a few cycles with no dishes and no detergent, on the highest temp setting. add a cup or two of white vinegar or dishwasher cleaner ( order online or get from an appliance repair store) through it. Dont forget your dishwasher has a filter in the bottom under the spray arm that needs to be cleaned periodically. if you dont clean it once a month it will get all kinds of nasty stuff built up in there.
Repair Help & Product Troubleshooting for Bosch SHX46A07UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch dishwasher is taking hours (at least 3 - maybe more) to complete a cycle. There is gummy, yucky stuff building up inside - sorta pinkish brownish. Could the water not be hot enough? A couple of months ago we installed an on-demand hot water heater and I wonder if that could have anythig to do with it. I've tried running the hot water in the sink first but that doesn't help. Any ideas


If your on demand heater is one of the small ones that mounts under the sink, it will not flow enough water to fill your dishwasher. the dishwasher is waiting for the water level to fill before it starts washing. your bosch will heat its own wat ... Bosch SHX46A07UC Built-in Dishwasher

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a JennAire jdb1090aws dishwasher. It's about 4 years old. The symptom is no water flowing through dishwasher. Approx 3 months after installation, the same symptom occurred. Tech resolved with float switch adjustment (no charge). Has run fine every since. I have not checked water supply, but doubt this is the problem (new water heater 3 months ago, sediment gone). I suspect the float switch is bad or out of adjustment. How do I trouble shoot float switch in dishwasher? Connect ohm mete


Hi,The procedure to test the float switch :-http://www.partselect.com/dishwasher+test-float-switch+repair.htmMost for no water entering the dishwasher, there are 2 main causes. One is the float switch and the other ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

I bought this dishwasher 5 years ago and was kept in the box until last month. I installed it, turned on the water and no water is being pumped into the unit from the water release valve in the dishwasher. I then checked all the cycles and everything works except for the pump. Then I checked to see if any power/volts was going to the pump and there is none. Could it be a wiring problem or could it be the circuit board?? please help. thanks


You will have to check all the connections visually. Since you know how to use a meter, see where the current stops. See if there is current coming from the control board to the pump. the water inlet solenoid valve should "free flow" water into the m ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Cloudy Dishes This condition suddenly started after couple of years. Water heater is 7 yrs old, never drained, therefore I think this could be the problem. I am going to drain it and report. I do have a whole-house water filter which I change out monthly or every other month. My guess is that without it, this problem would have surfaced long ago.


The problem is hard water. Go to www.dishwasherfilter.com and get their new product. It filters the water and takes out the hard minerals that cause spots and clog di ... Amana 24 in. ADB2200AW Built-In Dishwasher

Extremely heavy limescale residue on all items after dishwasher has finished. water temp in house has been turned down. Had water tested by city water company and results were clear. 12 months ago maytag replaced heater element under recall, but dishwasher always seems too hot. Neighbours do not have this problem. Any advice would be most welcome.we only use quality powder and rinse aid. Have cleaned dishwasher numerous occasions. model MDB4651AWS1 SERIAL # NW5015848


Hi,The scum, film and white residueproblems have started since the reductionof phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your dish ... Maytag 24 in. MDB4651AWS Stainless Steel Built-in Dishwasher

It always seems like it never gets enough water to even make the spray arms work. I have even tried to make sure I am not running any hot water in the house. It is about 7 months old and has always acted this way. Could there be something wrong with the installation? My old Sears never had this problem.


Sounds to me as if there is a blockage in the water line supplying the dishwasher or a kink in the water line supplying the unit. Since the water is supplied from the angle stop under the sink there could be blockage at that point. What I would sug ... Dishwashers

I have a Bosch SHU9915UC/U11 dishwasher, installed in 2002. Recently, our hot water heater had to be replaced, and we were without hot water for five days. Air got into the hot water pipes, and dried out all the debri in the lines. When we got the new hot water heater going, all of the sediment in the pipes ended up in the in-line screen filters in various appliances (clothes washer, etc.). I have cleaned these out, and these appliances are fine. Since then, the dishwasher has been shutting


All inlet valves have a screen built into the valve itself,shut off the water remove the entire valve and you will be able to see built in screen,if you flush out the debris from it and re-install the valve it should work fine.  ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have an ADG7550 whirlpool dishwasher. Am experiencing a fault when placing on a normal 65 degree programme it starts to fill and then defaults to pre-rinse and the start button and light flash eleven times. Can you explain what type of fault this could be ? I have had a similar problem 12 months ago when it was described as a water pressure problem which again was in the winter and wonder if this is the same. I would add that if I re-set the start button by holding it down and then re-start


... Whirlpool Dishwashers

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

What could be causing white powdery residue on dishes, glasses & silverware? I have checked the heater element - seems to be hot, using Cascade powder as usual, we have and have had hard water, we do have a new water heater set on 'low' setting - temp of water measured at 113 deg at kit tap. This washer has worked well for 12 years, then white powdery residue. Thanks, Phil


I wont vista ultimate product key ... Kenmore 13869 / 13864 / 13862 Dishwasher

We installed an LG dishwasher (LDF6920ST) a couple months ago. It has a horrible odor (stagnant water). Everything is hooked up according to the installation instructions. Draining problem? There is no water in the washer itself. Where would it be and how do we fix it?


Check that the drain hose end (connected to a garbage disposal?) is not plugged or connected to a slow/plugged drain.Then run an empty load and start up the dishwasher and wait until the water has finished flowing in. Then open the door ... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

No hot water from insta hot water heater


... GE GLDA690MWW / GLDA690MBB Built-in Dishwasher

I have a Miele G868 dishwasher. It is 15 yrs old. 8 months ago the soap dispenser wouldn't close, so I got another dispenser from Miele and replaced it myself. Everything worked fine until 3 months later, when the soap dispenser did not open. After 3 restarts, it began to function as it should. Now 5 months later, the soap dispenser is not opening at all. Here are my observations: 1. Economy wash cycle should run 35 minutes but only runs 13 now. 2. Water in machine is not hot, even though I run


... Miele Dishwashers

Water won't drain from bottom of dishwasher. I pulled the dishwasher out, blew through the drain tube, disconnected the drain tube and felt around inside. Ok there. The dishwasher has not been in use for 4 months, due to low hot water flow. I replaced a clogged valve today and restored water flow, and I'm wondering if non-use causes a problem with dishwashers?


Sorry to hear that you are having problems with your DW.Actually, yes. Not using a dishwasher for a while can damage some parts. Sediment from water damages the water valve. Food residues clogs the drain and drain pump. More likely the ... Dishwashers

I have water left over after each wash and it is really cloudy? I use the right amount of dishwasher liquid, etc. It has hot water. When I first got it about 2 years ago, it did not have this issue. I assume a little water left after the wash is okay? But, it is milky cloudy for the past 3/4 months now. I have a Maytag Legacy Series Quiet Series 300 machine...


Try running your disposal for a few minutes and then run through the rinse cycle. mine does this too sometimes and i just need to clean my disposal in my sink as some stuff gets caught up in it. ... Maytag 24 in. MDB9750AW Dishwasher

Dirty dishes Pump went on this machine about 6 months ago. Since the install of the new pump the dishes do not come clean. Particles finely ground or tomato seeds, sesame seeds etc. get blasted back on the dishes in the final rinse cycle. Repair guy has no clue... could there be a pinched line upon install that won't allow complete drainage, or the wrong pump? Is ther filter screen? I have done the vinegar reoutine plus a purchased cleaner to no avail. The machine is a bout 13 years old. Thank y


... KitchenAid Dishwashers

The water is pumped out after the rinse cycle then it continues to run and make an unusual noise but nothing happens. The noise is almost a grinding sound. There is also a smell like some part may be hot or the wiring may be hot. I can reset the dishwasher and re-run the cycle up until that same point and it does the same thing again. I have had a repairman out twice in the last six months. The first time he could find nothing wrong because the problem was intermittent and he couldn't see anythi


Timer \015\012\015\012or\015\012\015\012 ... Bosch Dishwashers

Service Manual Dear Sir, We are in the UK and although my double drawer dishwasher is branded Whirlpool ADG2900, I see that it is made by Fisher & Paykel. The top drawer motor started making a different noise about 3 months ago and now there is some dirty water left in the drawer after the cycle completes. The pots remain dirty. If you could get me the service manual I could try and sort it out. Please help! Thanks, RP.


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have an Electrolux dishwasher Model # EIDW6305GS1. I am getting an error "01", which means a leak is detected. It did this 5 months ago and the repair man replaced the pump and control panel. Now, after it happened again, I contacted Electrolux. The sent me a Leak Repair Kit, but with no instructions. I contacted Electrolux again and they said that they could not provide the installation guide. Can you help me located the installation guide or offer assistance?


... Dishwashers

My dishwasher emits a dead animal smell immediately after filling. I have a 20-year-old KitchenAid KUDS220T3 dishwasher. The racks are a little corroded, but it still cleans dishes just fine. About two months ago, it started smelling like a dead animal immediately after the dishwasher fills with hot water, during the time the water is being heated, but before agitation begins. The smell appears to be coming from around the door. If I open the door, everything inside the dishwasher smells fine.


This vent that you are describing is to allow air to flow in for the heat/dry cycle. Some times little creatures want to "mark" their territory by "spraying". Spray some type of cleaner like ammonia into it and **** it out with vacuum a few times. Mo ... KitchenAid Dishwashers

MY SECOND WHIRLPOOL ADG7460 DISHWASHER WAS INSTALLED THIS JULY WHEN MY FIRST(DURING IT'S FIRST YEAR) COULDN'T BE FIXED AFTER 4 ATTEMPTS, THE HEATING ELEMENT KEPT BREAKING DOWN, HENCE NO HOT WATER NOR DRYING. NOW AFTER JUST 2 MONTHS THE SAME PROBLEM HAS OCCURRED WITH THE NEW ONE. ANY IDEAS????


... Whirlpool Dishwashers

About a 3 year old maytag stainless steel inside dishwasher, not cleaning, often soap resdue on dishes or silverware, I use fresh new cascade, checked to see if washer fills with hot water, seems to up to the bottom of the door when I open durning cycle, arms go around, no obvious plugging of the screens, no junk in the foot chopper propeller, no paper or plastic or food in the jets of the arms. Motor went out on it 9 month ago and I had it replaced by appliance repair station here in Missoul


Water must be 130 Deg F to wash properly. ... Maytag Dishwashers

Gld4260l00ss has power. there is light indicators on front panel, but when press start button, nothing. new inlet water valve solenoid installed last month and unit has ran fine until two days ago. I have unplugged power and plugged back in but no help.


I would remove the control panel and ck the ribon form the touch pad to the control .it is very common for these connections to fail remove the ribon and re insert it and try again . also ck the touch pad and make ... GE GLD4260LSS Dishwasher

Kenmore ultra washer II 1993 two months ago white chalky film on all dishes. cleaned out used vinegar running hot water first, gel pacs, what's wrong


Sounds like too much rinse agent (jet dry) ... Kenmore 24 in. 15932 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1709 seconds