Having problems with your Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer ?

When I start it the engine surges. When I pull the handle on the wand the engine will not go to max rpm.


Answers :

Check to see if the choke is not on.
Repair Help & Product Troubleshooting for Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I start it the engine surges. When I pull the handle on the wand the engine will not go to max rpm.


Check to see if the choke is not on. ... Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer

Karcher G2650 OH - When I start engine pressure builds up and the engine will stop- When I pull the wand handle back - I get a high release of pressure - I can hold the wand open and start the engine and it will run until I close the wand - egnine stops


Take a look at this link, I think this might solve your problem\015\012\015\012http://www.wmpcs.com/blog/?p=72 ... Pressure Washers

I have the Karcher 2400 psi, 5.0 Honda engine. Starts fine, but when you pull the handle on the spray wand, the pump does not kick in and the water just continues to trickle out of the end of the wand at regular faucet pressure. Occasionally the "clutch" will kick in and you have full pressure, but if it does and I let off of the trigger then chances are that it won't kick in again. has been getting worse for several years.


... Karcher 2500 PSI Pressure Washer

8hp honda engine on log splitter. costantly stalls as governor opens throttle to maintain rpm. engine starts to stumble then stalls. When revved with throttle acts similar. somewhat better when hot, somewhat better at half choke. have pulled carb and checked bowl, float, pulled main jet checked, blew carb out but no better. No dirt or gum in carb, looked new. all gaskets looked good. engine has low hours.


... Honda 8 HP Engine

I HAVE AN EXCELL PRESSURE WASHER-MODEL EXPRO 2530-HONDA ENGINE GX200QX2-IT HAS A CAT PUMP MODEL#2SFX30GZ1. IT IS VERY HARD TO CRANK UNLESS YOU DEPRESS THE HANDLE ON THE SPRAY WAND WHILE CRANKING.ONCE STARTED IT WORKS FINE UNTIL YOU RELEASE THE HANDLE AND THEN THE ENGINE QUITS.IT DOES NOT GO INTO BYPASS MODE.


... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

I have a Honda Excel Pressure washer with 5 hp engine. I just started using it for 5 - 10 minutes and the engine stopped running. I can't pull the cord to turn over the engine. Ithas plenty of oil, I disconnected the hose and the wand and still can't get the engine to turn over.What next?????


... Pressure Washers

Pump Issue I have a john deere pressure washer. I hook the hose up to it, rurn the water on and no water comes out of the wand. I started the engine briefly and pulled the trigger on the wand and still nothing. The model number of the pump is Annovi Reverberi SJV 2.5G24-1. I can't seem to find any info on the G24? There is info on the G27-1. Not sure what to do here? Please help.


... Pressure Washers

Unloader adjustment Starts only with handle pressed. Upon release of wand handle engine dies. Can it be an unloader adjustment or lubrication issue?


... Craftsman 2550 MAX PSI Briggs & Stratton Powered

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Hi, Karcher calls the unloader valve a spill valve, this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps ... Karcher 2500 PSI Pressure Washer

I have a honda GX240K1 on a BCS tiller. The engine seems to defy reason. I have adjusted the governor, set the max speed screw, adjusted the idle speed and have achieved some success but cannot seem to control max RPM's. The engine max's out at over 5K. I have tried about everything I can imagine yet nothing seems to fix it. Spec's say that it should idle at about 1400 Rpm yet it seems to idle best at about 1800-1900. I am using a EZ328 instrument to check the engine RPM and it's reading i


Hello. It sounds like the governor is either out of adjustment or in need of replacement. I agree that you should not run this in this condition or you will have a much larger repair to do. I would replace the governor. J. ... Honda 8 HP Engine

Honda Pressure Washer Black Max 2600 Psi 161cc Problem: manual choke pulled on when starting. When attempting to turn off the choke the motor dies. This occurs no matter how long the engine runs for.


... Honda Black Max 2600 PSI Pressure Washer

I have a Briggs Stratton Model# 020228 Gasoline Pressure washer with a Faip Brand Pump. The engine starts, the water supply goes thru the pump under its' own pressure. When I pull the trigger on the handle, there is not increase of force nor does the pump engage. I had this same problem several years ago and sent it to a dealer for service. His service tag indicated a stuck unloader. Where is the unloader located on this pump. The indentification on the pump is MTPV90736 191693 Order # 52


... Briggs & Stratton Pressure Washers

Surging and stalling When just started, the pressure won't rise with the wand. When the trigger is applied for long periods of time (1 minute) the engine stalls


Thought it was a free advice web site? Scammin' scumbags!!! ... Honda Pressure Washers

I have a kohler command pro 8.5 on a porter cable pressure washer. Yesterday it started just fine. Today I pulled the start rope and there was no resistance and the engine did not turn over. The pull rope rewound just fine and I tried again with the same result. After several tries it caught just a little near the end of the pull and the engine started. What is the cause of this problem?


... Porter Cable Pressure Washers

Hard starting 6hp Briggs and Stratton power washer engine. I poured a teaspoon of gas into the cylinder; reinserted the spark plug and with one pull in ran fine. This is a choke start engine and it may take 12 to 15 pulls to start on a cold engine. The unit is clean. The air cleaner is new. The spark plug is new. The unit is 2 years old with very little use.


Hello. I have this same machine. Go to the auto parts store and get an aerosol can of starter fluid. Have a helper squirt some into the air intake while you start it. Then continue to squirt a little starter fluid as it runs for the first two mi ... Campbell Hausfeld Pressure Washers

I have a Troybuilt pressure washer which has a Honda GC160 engine. The engine starts easily but quits after about a minute. One pull and it re-starts, then quits in a minute....... This goes on for as long as I want to keep re-starting it. Anyone know what it might be? I pulled the carb off and blew out all of the various ports I could find. I did not remove the carb adjustment screws as I have not had any luck getting them back in place during previous problems with other gas engines.


... Karcher 2500 PSI Pressure Washer

Very Hard to Pull Cord to start engine on Northstar Pressure Washer. When I remove spark-plug it is very easy to pull cord. With plug reinserted it is extremely difficult to pull cord to start engine.


On the Honda motors very hard pull starting with no start ck for broken rocker on exhaust or intake, I've already repaired two with this problem...... ... Northstar Pressure Washer 3000 PSI

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

Hi I have a mdb6601awb maytag dishwasher. Sometimes when it starts the wash cycle it will make a loud squelling noise. Then if you pull on the handle and stop it, the machine will start and sometimes the noise will be gone. Or you may have to do this 3 or 4 times before it will stop making the squelling noise. I do notice when I pull up on the handle to stop the machine it makes some clicking noises and then the noise goes away. Thank You for any help you may be able to give me!!!


I don't have a solution however I have the same problem with that same model. ... Maytag 24 in. MDB6601AWS Stainless Steel Dishwasher

Home Depot has a lawn mower with the Honda GCV160 Electric start version engine. They also have a pressure washer with the Honda GCV160 engine. I have a disability that makes it difficult to pull the starter rope. I would like to get the electric start on the pressure washer. My local Honda bike shop service center said they use different blocks. Can I get a pressure washer pump mounted to the Honda GCV160 Electric start version engine? If necessary, are there adapter plates that can be purchase


... Karcher 2500 PSI Pressure Washer

I have a Honda GC160 motor on a powerwasher. The engine stalls when I release the power wand handle, but if i keep the handle squeezed, it works but the engine sounds like it is laboring.


... Honda Pressure Washers

I have a 5HP Honda engine installed on a Excell pressure washer. While the engine readily starts, it will not continue to run unless I keep the choke setting nearly completely closed. When I activate the pressure gun, it seems to generate adequate pressure, however, when the trigger is released, the engine continues to run at the same rpm instead of the normal variable rpm that most engines operate at during idling periods. The engine will always cease running when I push the choke rod all the w


... Honda Pressure Washers

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Karcher 2400 pressure washer with honda engine. my problem is that i've installed a new rebuild kit in the pressure pump assembly, and now, when i reinstall the assembly back on the engine, i cant even pull start the engine over. its too tight! when i loosen back on the pump assembly, i'm able to pull the engine over. what have i installed wrong from the rebuild kit??


The pump is correctly oiled and lined up on the camshaft, correct? ... Karcher 2500 PSI Pressure Washer

The engine starts just fine. Everything goes okay until I pull the trigger on the spray gun and then the engine stalls out within 2-3 seconds after the water starts coming out. It is a 2700 Briggs and Stratton engine.


One thing I have found about pressure washers...you need to run water through the hose and everything until you get all the air out...or they will bog down and such until the air is out. ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1299 seconds