Having problems with your Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer ?

Have pressure when first pull triger than pressure fads

\015 Pressure washer is a craftsman model 767200 2250 psi just replaced unloader vlv\015

Answers :

Check the valves inside for sticking
Repair Help & Product Troubleshooting for Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have pressure when first pull triger than pressure fads


Check the valves inside for sticking ... Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer

Pull my pump first startsthe pressure is good as soon as i pull the trigger the pressure is gone as long as i hold trigger just faucet flow let go of it pressure builds up until i pull trgger , no pre


... Annovi Reverberi RMW2.5G25D

Won start Was using the pressure washer 1st time this year and started on the second pull. Ran out of gas shut-off also noticed it needed oil. Believe, I put too much oil so, I drained some and added gas. At first, there was no resistant in the pull so waited an hour and tried again. This time the resistant was there on the pull but still would not start; no attempt even to turn over. It's been a couple of days...changed the spark plug although, hardware guy said nothing was wrong with it..still


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

PRESSURE WASHER RUNNING BUT NO WATER COMES OUT WHEN YOU PULL THE TRIGGER??? IT WORKED FINE WHEN I FIRST STARTED IT. I THEN SHUT IT OFF TO MOVE IT. WHEN I STARTED IT BACK UP, IT STOPPED WORKING.


The water admittance valve is stuck. The spring loaded valve lets more water into the pump when the pressure drops when you trigger the wand. Take the valve apart, clean the bore with crocus cloth on a dowel rod. Replace the O Rings and lube with ... Pressure Washers

No water I have a sears pressure washer. I hooked up the garden hose and pulled the triger with the engine off. No water. I disconnected the spray gun hose, were it connects to the pump.Turned on the hose,no water.Could the pump be cloged?


... Pressure Washers

My pressure washer starts on the first pull but shuts off right away.how come


The carb is dirty, drain the carb bowl sump, then if your lucky get fresh gasoline and clean and refill the gas tank,also get a spray can of carb cleaner into the intake from the parts store and while running & gently spray into intake as not to ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Pressure is fine when first started ,if trigger released no Psi


Your uplift injector valve in the water pump is sticking. You need to remove this part. Lube the top o-ring only with a water proof grease. Reinstall this part. You will be up and running again. \015\012\015\012You need to use needle nose ... Karcher 2500 PSI Pressure Washer

I recently purchased a northstar 4000 psi pressure washer. I had the same series pressure washer for the past 6 years and used a downstream chemical unloader quick connect to pull chemical. I attached it to the pressure washer and it is not pulling. I havent modified anything and I dont want to pull chemical through my machine.


The injector might be worn out or have something inside of the valve causing it not to ****. If you are using a new high pressure hose or a longer hose this may also have an effect over the injector not working. ... Northstar Professional Series Pressure Washer 4000 PSI

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

Hesistation on pressure when trigger is pulled get n worse


Unloader valve is the most likely suspect here.Remove and clean with penetrating oil then reinstall.Also add some LIGHT oil into your supply hose via a small funnel. 3-in-1 household oil or power steering fluid lubricate the ... Honda Karcher G4000RH Pressure Washer

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Hi, Karcher calls the unloader valve a spill valve, this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps ... Karcher 2500 PSI Pressure Washer

When i pull the triger the pressuregoes from high


... Karcher G 2600 VH Gas Pressure Washer

Karcher 620M.To obtain high pressure I have to Move pressure control on nozzle several times until pressure kicks on. As soon as I release trigger and then pull it again, I have same problem -- giggl


... Pressure Washers

Karcher 2400 pressure washer with honda engine. my problem is that i've installed a new rebuild kit in the pressure pump assembly, and now, when i reinstall the assembly back on the engine, i cant even pull start the engine over. its too tight! when i loosen back on the pump assembly, i'm able to pull the engine over. what have i installed wrong from the rebuild kit??


The pump is correctly oiled and lined up on the camshaft, correct? ... Karcher 2500 PSI Pressure Washer

Pressure Washer I have a Porter Cable pressure model no.PCH2401.It works fine for 5 minutes,then I can hear the motor loading down and then it stalls out. I tried to start it and it was very hard to pull on. disconnected the water supply and if was very easy to pull and started right up. I noticed the pump was very hot.This unit has a thermal relief valve on it,shouldn't it have released when it gets to a certain temperature .I was thinking maybe this is why it might be shutting the motor


Any leaks from connection at pump to gun and wand assembly if so the valve is detecting leakage and open up again without u squeezing trigger it builds up in the head.if your trigger gun is leaking internally then you will need to replace the gun thi ... Pressure Washers

Honda gc160 when I first pull it. It wants to start. Then dies in 1/2 second. I have put a new fuel punp, plug, and coil on it and opened the carb at float. cleaned it there. it will not do anything after the first pull untill 15 min latter, then it does the same thing ?


... Pressure Washers

I cant pull the cord in my pressure washer it feels like it stuck thiere is no pressure in it it wont pull


Take the sparkplug out and see if you can pull the cord then. If fuel comes out of the sparkplug hole the carburetor is leaking gasoline in to the engine filling up the cylinder causing the lockup. The carb has to be rebuilt. Another problem mice lik ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

I have Honda pressure washer.Inorder to start the pressure washer you have to pull the cord. THe cord is stuck and I am not able to pull the cord. Why it and what should I do to start the washer.


... Honda 2500 PSI Gas Pressure Washer

I have a mi-t-m pressure washer in the ca-series.The problem is the motor shuts down at times with out any reason. The first time I used it was on a house with a well supplied water. It worked fine,brought it home where I used it with no problem. It was used twice that first year. I then winterized it.The second year brought it out to the same house,I was using it for about a half hour when it just shut off with out any notice. I noticed there was back pressure in the engine when I tried to rest


Mi-t-m pressure washers have a Low Oil shutdown feature that turns off the motor, this is often causing similar problems on this kind of appliance.Have oil checked, if oil is fine , then the sensor that controls oil pressure and activate ... Pressure Washers

Pressure issues My pressure washer builds pressure and has a powerful first burst and then no pressure


Sounds like the pump is damaged; most likely from freezing. Needs anti-freeze if stored in cold temps. Repair or replacement of pump may be close to replacement cost. ... Troy-Bilt 020528 Gas Pressure Washer

No pressure i bought a used 2800 psi pressure washer has a 190 honda engine i can't fine the model number it has no pressure i pulled it all apart the only thing that i found was the pressure adjustment was stuck i freed it up.


... Pressure Washers

I have the Coleman powermate 2400 PSI pressure washer and on initial start it sprays and has great pressure. But once I release the spray handle it will not spray again, not even one drop of water. I have verified water pressure, bought 3/4 hose, and also changed the spray handle with no help. Pressure washer was bought new at Lowes, but did not use for first three years of ownership, should have tested it. Thanks for any help on this. Ted Miller


Sounds like the valve in the handle is sticking closed. May have a broken spring, or maybe a part is stuck..\015\012I say take it apart, and the answer will present itself.. Play with it with nozzle out too... Maybe something is stuck after st ... Coleman Pressure Washers

I have 2400psi washer gas will run w/hi pressure, when i release trigger and then pull trigger for hi pressure it will take minutes to get hi pressure, longer i run longer for pressure to come back.


Hi and welcome to FixYa. I am Kelly. \015\012\015\012First off check to see if there is an inlet screen at the house water hose connection point. Remove it and clean it then reinstall. If the screen was clean.......\015\012The u ... Honda Karcher G2400HH-R Pressure Washer

My pressure washer has no pressure. this is the first time this year i have used it, hooked it up properly, turned it on and no pressure other than hose pressure.


... Karcher 1750 psi Electric Pressure Washer

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0842 seconds