Having problems with your Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer ?

I have a troy/built pressure washer it somking what could b the problem

\015 Its smoking from the exhaust\015

Answers :

Repair Help & Product Troubleshooting for Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Troybuilt pressure washer which has a Honda GC160 engine. The engine starts easily but quits after about a minute. One pull and it re-starts, then quits in a minute....... This goes on for as long as I want to keep re-starting it. Anyone know what it might be? I pulled the carb off and blew out all of the various ports I could find. I did not remove the carb adjustment screws as I have not had any luck getting them back in place during previous problems with other gas engines.


... Karcher 2500 PSI Pressure Washer

I have a troy/built pressure washer it somking what could b the problem


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely. the oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any. I will


There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing. Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. It is v ... Dewalt DPH3100 Gas Pressure Washer

I have gcv 160 5.5 hp power washer my problem is that the high pressure pump is not working properly when the engine is running the output pressure is very low so i would like to know could be the possible cause of that problem


look for a black plastic cover with a silver snap on top; pry off the silver snap and lift off the plastic cover; next remove the two screws on the top plate then pull out the piston inside - if unable to lift out, start unit and watch it pop ... Karcher 2500 PSI Pressure Washer

I borrowed my friends pressure washer and it was working when i had it but she says its not now, could u tell me what u think it could be please. Could it be a motor problem and if so can u explain how a motor would go without me touching it as i dont like the idea im being acussed of breaking it when it was working when i gave it back


The water has emptied out of the machine in transport you may have to bleed the air out of the pump ... DeVilbiss Pressure Washer Hose 25' 38" Id Rubber Has

I have a G2500VH pressure washer that has started to pulse when the trigger is squeezed. This happens if I use the 0,25, and 40 degree nozzles BUT if I use the one for low pressure(detergent use) it will hold pressure fine. I have changed the unloader valve, checked all the valves and seals ad they seem to be fine. What could be the problem?


Do you mean pressure on and off with the hp tips and smooth and steady with chemical tip? ... Pressure Washers

No pressure what could be the problem - Campbell Hausfeld Pressure Washer Gun - Electric/Gas Up To 2200 Psi - PW102400AJ


... Campbell Hausfeld Pressure Washer Gun - Electric/Gas Up To 2200 Psi - PW102400AJ

Rockworth Powertask Pressure Washer : model no AROW4P seems to rev flat out, hav to put choke in middle to use so not to fast revs. Im sure it used to rev higher and lower according to use of lance. could it be something to do with 3 valve things if so how could i tell if ok. put clean fuel in. oil level ok.another problem is when switched on water comes straight through lance,trigger makes no diffrence. please help


... Pressure Washers

Power washer starts no problem but when turned on and activating the trigger on the pressure washer gun, water no longer comes out. The gun itself was replaced not long ago. What could be the cause?


The tip could be plugged up ... Honda Pressure Washers

When using my pressure washer john deere 3800 at the time i press the triguer, it looses pressure. What could be the problem?


... Dewalt Pressure Washers

I have no pressure coming out of my Craftsman 2150 pressure washer. It is only about 2 years old and I only used it about 4-5 times. I hooked it up today and it only has the strength of a garden hose. what could be my problem?


IS THE MOTOR RUNNING? IF SO THE PROBLEM IS IN THE PRESSURE CONTROL VALVE OR PUMP PISTON ITSELF, IN MOST CASES THIS IS ALL ONE PART SO IT MAKES NO DIFF WHICH ONE IS AT FAULT, REPLACE THE PUMP. ... Pressure Washers

I have used my Honda Pressure washer 3 times over a period of 1-2 years. I could not get it to start today. I did not drain the old gas but added some new gas (which was probably a few months old). I have never had problems with a lawn mower sitting for a few months; but my guess is, this is the problem? How can I repair this?


Check the oil level in the crankcase if it just spills out the oil fill hole it fine\015\012\015\012drain tank and drain float bowl and clean fuel tap make sure the carb is not green and blocked if so give it a good clean out ... Honda Pressure Washer PSI 3000

Hi, I have a problem starting my Craftsman 2450 PSI Pressure Washer, Model 580.752310, could you help? I've changed the spark plug.


... Craftsman 2500 PSI Briggs Stratton Powered Pressure Washer

I have a dewalt dp3100 pressure washer, i was using it for about an hour then it ran out of gas. After adding some gas it refuse to stop, it start for a few seconds then it would stop. its full of oil (but the oil is a little dirty) and the gas is half full. what could be the problem?


... Dewalt DPD3100 Gas Pressure Washer

Start problems The 1st time I tried to start my Honda 2400 pressure washer the pull cord came all the way out with no resistance and it wouldn't recoil. I took it to a repair shop and they said atyhe engine was shot due to a broken piston. How could this have happened and is a new engine the only fix?


... Honda Pressure Washers

My Troybilt pressure Washer Model 020207. runs forabout 30 seconds then the motor stops. Acts like motor is locked up. Motor can't be pulled until water hose is disconnected. Took the water pump off and the 6.75 Briggs starts and runs like new. What could be the problem.


It sound like a digafame problem/or/carborater bowl has some water or needel valae is sticking cheack them if not the problem then you may have a crank shaft problem good luck see if there is oil in motor ... Briggs & Stratton Pressure Washers

I have a John Deere pressure washer with the AR RSV 4G40 pump; it will not pull up the soap any longer. I have only used it a few times, which it worked great, and now it doesn't work! Anyone have any ideas what the problem could be


... Annovi Reverberi AR Pressure Washer Pump RKV4G40-PKG

I have a Whirlpool Dishwasher model gu1200xtlq1 and the issue we are having is that the water pressure while the washer is on is very low? We were wondering what the problem could be.


... Dishwashers

I have had 3 Karcher pressure washers all experience the same problem and so have two of my neighbors. Our area has very hard water and it causes problems with the washer not bringing up the pressure when the trigger is pulled (or surges up and down) and the nozzles clogging, etc. The service repair facilities cannot tell me how to prevent this. Many attempts to contact Karcher for advice have been ignored. I have been thinking that perhaps running the engine for a few seconds with no hoses a


If your water is that hard (and it appears it is) WD40 will NOT solve the problem. You should look into a water softener. However, chances are that a small, inexpensive model will not have the flow capacity required for a pressure washer. You'll like ... Karcher K2.26 Electric Power Washer

The last time I used the pressure washer was running fine. A few minutes later I tried to start it up and could barely turn it over. I removed the recoil and could turn it a little easier backwards. The motor is a Honda GC190 on a karcher pressure washer and has 20 -30 hours of running time. Thanks Clint


... Karcher 2500 PSI Pressure Washer

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

Deville Excel Model # EXHA2425 Pressure washer I have a deville excel Model # EXHA2425 pressure washer. I went to the deville website (devap.com) which forwarded me to the dewalt site w/ exploded diagram below. I am having problems with intermittent pressure production. If I squeeze the trigger sometimes it will have pressure, somethings it will not. If I repeatedly squeeze, then release the trigger sooner or later I will get pressure. Someone on hear had told me it was a "bypass valve sticki


You\015\012need toput antifreeze in the out/outlet or/oil then start it up you are driing out the seals allways put away with repeating this step ... Karcher 2500 PSI Pressure Washer

My Karcher K3.48M pressure washer remains in the low pressure mode even when I return the pressure nozzle to the high pressure position. How can this be corrected. The pump seems to build up the pressure because when I release the handle the pump motor stops. This is a fairly new pump which was purchased in the latter part of last year(2010). Could this have been caused by the detergent I have been using which is an automotive shampoo? Please help I love this washer and for the times that I u


... Karcher PSI Electric Pressure Washer

If while pressure washing I let off the wand trigger it looses pressure and I have to turn of the washer motor and wait for the pressure to return.(seems like some kind of vapor lock problem)When the pressure returns I hold the trigger and restart the washer. If I let off the trigger we go through the same process again. this is a g3050


Hi and welcome to FixYa, I am Kelly. \015\012 This is most often caused by the bypass / un-loader valve located on the high pressure output side of the pump. The valve will either have a stem type valve with a knurle ... Karcher 2500 PSI Pressure Washer

Deville Excel Model # EXHA2425 Pressure washer. Is "unloader" the same as "bypass valve"? I have a deville excel Model # EXHA2425 pressure washer with a 5.0 Honda enginr. I went to the deville website (devap.com) which forwarded me to the dewalt site w/ exploded diagram below. I am having problems with intermittent pressure production. If I squeeze the trigger sometimes it will have pressure, somethings it will not. If I repeatedly squeeze, then release the trigger sooner or later I will get p


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1255 seconds