Having problems with your Briggs & Stratton Gas Pressure Washer 20244 ?

I think I may have put too much oil in the unit. How do I drain it?


Answers :

Should be 20 oz of oil...there`s a drain plug on base or open up the oil fill cap and tilt engine over into a bucket will work also good luck
Repair Help & Product Troubleshooting for Briggs & Stratton Gas Pressure Washer 20244

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I think I may have put too much oil in the unit. How do I drain it?


Should be 20 oz of oil...there`s a drain plug on base or open up the oil fill cap and tilt engine over into a bucket will work also good luck ... Briggs & Stratton Gas Pressure Washer 20244

I have a sears pressure washer, model 580752300. The pump on the underside vibrated lose and broke a couple screws. It came off and the oil drained out. I replaced the screws and it's ready to go except I can't find out how much replacement oil to put back in. Sears has larger containers but won't tell you how much oil to put in. However, there's a pricey pre-measured container they want to make you buy. Anybody know how much oil goes in that pump?


... FAIP Non Marking Pressure Washer Hose 4000 Psi, 50ft. Length

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Won start Was using the pressure washer 1st time this year and started on the second pull. Ran out of gas shut-off also noticed it needed oil. Believe, I put too much oil so, I drained some and added gas. At first, there was no resistant in the pull so waited an hour and tried again. This time the resistant was there on the pull but still would not start; no attempt even to turn over. It's been a couple of days...changed the spark plug although, hardware guy said nothing was wrong with it..still


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Hotpoint hda 3420 dishwaher. when turning, on the motor hums and doesn't kick in like usual. manual says caused by non use. "must keep the seal moist" put water in the unit, thinking it might get the seal moist. bottom filled and unit has not worked for days. assuming it's this seal: where is it? how do i get at it? what is replacement difiiculty? how much is the part? thanx ron [email protected] or [email protected]


Hi,Before thinking about replacement... pour a couple of cups of water in the dishwasher and let them soak the seal for overnight...Then if it don't go give the motor a spin...just to make sure it will go...if that don't work ... Dishwashers

Dishwasher filling up and over flowing. switch to turn on pump comes on late or when I manually put pressure on drain. Have hard water and found much scale. could sensor/float scale cause this? Thinking about filling with white vinegar and letting sit so I don't have to take apart. Thoughts?


Take a packet of unsweetened lemonade any brand and run it through a cycle. This will clean all the scale and calcium from the pump and spray arm to improve the circulation of water in the machine. ... Asko Dishwashers

Kenmore 665.16762000 We were washing dishes the other night and my husband walked into the kitchen to find water pouring out of the "air gap" in the sink. Now we cant get the unit to come on. Ive tried some of the various combinations of button pushing to re-set, but so far still not operating. I am thinking it may be the "thermal fuse" due to some other questions here, but how can i confirm.... and the biggest question... how much is that gonna cost me to replace if i do it myself?


... Kenmore 16762 Dishwasher

My washer will not drain the water I think that the pump has gone out in it is it going to be cost efective to put a new pump in it or should i just replace the entire unit


You could just need to clean out the sump if the drain pump impeller is jammed. Below is a link to a video you can download that will show you how to repair a Bosch Dishwasher that isn't draining. ... Bosch 24 in. SHU43 Built-in Dishwasher

Hi - I've been all over your web site and keep getting rejected - alas. I have one of those wonderful Fisher Paykell double drawer dishwasher unit Model # 88445 (I think but also see another number LIM725367) I bought in new in 2007 worked fantastic but tore down my b ungalow now have a new kitchen ready for it. Carol 303 320 1697 [email protected] May 6 2011 11:30 AM MDT I would like to obtain an installation manual so I can make sure I packed all the parts and then put it in m


Hello Carol - \015\012\015\012\015\012The full model number for future reference is DD603-88445. I've uploaded the installation manual for all Fisher & Paykel DD603 double-drawer dishwashers to Rapidshare. Please follow the instruc ... Dishwashers

SHU66C05 Unit will not drain at the end of a cycle. I can use the cacel/drain to manually get dishwasher to drain so don't think it is the motor/ drain pump. I replaced the air trap and the hose to the disposal, (neither appeared clogged) so I think it a problem with the swiching board.


Yes it appears to be in the micro controller board. Try to get the same version board being software driven. Better to take the help of the BOSCH service provider. ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

Hello, it seems that my maytag does not drain properly anymore.it leaves a puddle of water at the base all the time...I think its because particles of the dirt may have clogged the output of the drain. what can I do to fix this problem...many thanks in advance. you may reply at my email address at [email protected]


... Maytag Dishwashers

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

My whirlpool motor does not sound like it kicks on when started. The dishes are not getting cleaned...and water remains in the bottom. When I hit drain, it will drain. I also recently noticed that I am having to use my garbage disposal much more often and do not even put much food down it. Could it all be related? PLEASE HELP!!!


Yes it's most likely related. Your dishwasher dumps all the debris it washes off the dishes into the garbage disposal. I'm not a dishwasher distributor so I can't tell by the model number just what dishwasher you have.\015\012 Most people dump ... Whirlpool GU2400XTP Built-in Dishwasher

We have a bosch she4am dishwasher and just recently the unit doesn't rinse all the soap out of the glasses of the top rack and also a film is being left on the dishes. i have checked the top spinner and it works fine, cleaned out the drain, only use recommended soap tablets and use jet dry. we recently put in new counter tops but i didn't move the unit itseld only the drain- would this have any effect?please help


Check the top of the cabinet after the unit has started to wash the water droplets is the key. if you see water droplets on the very top all over then the unit circulation pump is working. If that checks out then check the jet dry compartment. here ... Bosch SHE4AM06UC 24 in. Built-in Dishwasher

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Installed an older model dishwasher for a friend power works oes throuth the cycles but its not pumping water into the uniT there is no clogs and i hear the pump turn on. unsure why its not getting water into the unit another friend thinks its cause the air tube isnt hooked up but i think it may be something more then that any ideas


You will need to disassemble the bottom part where the bottom rotary spray nozzle is(the part that shoots water upwards). The impeller might have come loose or it is clogged in that area. ... Hotpoint Dishwashers

I just replaced the drain pump in my bosch shu3307uc dishwasher.When I turned it on it filled with water and then I put it in the drain mode' It drained but it would not allow me to advance to start the wash cycle from the beginning. How do I advance this unit? It was working fine until drain pump went out.


You have to allow the drain cycle to finish completely, or find cancel drain dot points and press both at the same time, to reset program, open the door and close it to make sure the micro-switch activate properly ... Dishwashers

There is water in the bottom of dish washer after finishing. If I start another cycle, everything drains, so it's not a problem with the hose. I hear water draining. I think it is the drain time. When the machine was under warranty, the service guy came and changed the drain time to longer. He told me how to do it, via the buttons, but have now forgotten where I put such great information. I have a 1996 built in model.


We have come up on this many many times. It is not drain time. There is a flapper in the drain hose located where the hose attaches to the pump with towels remove the hose and stick you finger in. It is and angled piece of rubber so it will be dif ... Whirlpool GU2400XTP Built-in Dishwasher

After putting too much down the garbage disposal, the sink will not drain and the dish washer (Whirlpool Quiet Wash) will not drain. I have disconnected all sink drain pipes and snaked the main line to be sure lines are clean. The drain hose from the disposal to the washer seems clear. What should I try next?


You need a longer snake had one on friday that wa about 40 feet out it took two trys to get it good luck ... Dishwashers

I've had my Nautilus for 6 years and it cleans very well - but now, it won't drain fully and pools at the bottom of the unit. I have made sure that my garbage disposal was cleared first, too. and that water was draining properly in the sinks. I will need special tools to unscrew the drain filter in the dishwasher, right, or can I just use a pair of pliers to turn the little knobs? I am always careful to rinse all food off the dishes before putting them in the washer, but I guess I wasn't careful


If your model has the screen across the back with the filter, then yes use your fingers or a plier to unscrew the pop up valve assembly at the very back center of the dishwasher. Most likely, the cone shapped part has deteriorated and is not sealing ... GE Nautilus 24" Built-in Dishwasher

Brown scum accumulates under the large circular aluminum plates on the bottom of the drawers. Has to be cleaned out every 1-2 weeks. We have never had a dishwasher that required so much maintenance. We think it is the size of the drain. Can this be fixed by installing a larger drain hose. We have cleaned out the drain hose and it doesn't stop the problem.


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a KitchenAid dishwasher kuds01djss0 and it will not drain at all. i have checked the drain hose and there is no clog. Any ideas? I think it may be the drain pump........


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

Water will not drain out of bottom of dishwasher.It will go through the whole cycle but will not drain. This is a Frigidaire model no.FDB510LCS3 Serial no.is:noth70219331.Pump hose was disconnected and drained completely,dishwasher was put through another cycle and still ended up with water puddled in the bottom!! Could this dishwasher be called a lemon??? Does the pump need replacing?? I have noticed on your website that many others are having the same problem.To me it appears that it may be sh


Check the input to the drain hose to make sure it is not blocked by something like a cherry pit.  That could cause the water to not drain fully. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Kitchen Aid Dishwasher KUDR24SEBLO does not drain 100%. I have removed the drain hose and chcked the sink P-Trap, [it drains thru the garbage disposer]. Unit is 10 years old, otherwise works fine. I am having difficulty removing the impeller and items above the pump to see if it is clogged. Do you think I have a partially clogged pump or a timer issue that prevents the pump from completely emptying the bottom of the dishwasher? We have run the dishwasher 20-30 times since observing the problem.


Hi there,\012Please check out the following -Pump - Your dishwasher pump ejects the water. The pump is usually mounted directly to the motor, then attached to the bottom of the dishwasher. You can reach the pu ... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0876 seconds