Having problems with your Briggs & Stratton Gas Pressure Washer 20244 ?

Pressure Washer 11P902-0127-BI 10072262 TroyBilt help

\015 Used one time and now won't start. Replaced spark plug, oil and replaced gas...\015

Answers :

Repair Help & Product Troubleshooting for Briggs & Stratton Gas Pressure Washer 20244

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pressure Washer 11P902-0127-BI 10072262 TroyBilt help


... Briggs & Stratton Gas Pressure Washer 20244

I have the Coleman powermate 2400 PSI pressure washer and on initial start it sprays and has great pressure. But once I release the spray handle it will not spray again, not even one drop of water. I have verified water pressure, bought 3/4 hose, and also changed the spray handle with no help. Pressure washer was bought new at Lowes, but did not use for first three years of ownership, should have tested it. Thanks for any help on this. Ted Miller


Sounds like the valve in the handle is sticking closed. May have a broken spring, or maybe a part is stuck..\015\012I say take it apart, and the answer will present itself.. Play with it with nozzle out too... Maybe something is stuck after st ... Coleman Pressure Washers

Have a Husky Pressure Washer 2200 psi, HU80931. I don't have an owner manual. It has set for about a year. When I started the washer there was very little pressure. Did some cleaning and it was a little better, but now there is no pressure and I am having trouble keeping it started. Can you help? The washer was purchased at Home Depot and it has Briggs and Stratton the the washer too. Thank You, RJ


Look at eReplacementParts.com and the parts diagrams ... Briggs & Stratton Pressure Washers

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

My Karcher K3.48M pressure washer remains in the low pressure mode even when I return the pressure nozzle to the high pressure position. How can this be corrected. The pump seems to build up the pressure because when I release the handle the pump motor stops. This is a fairly new pump which was purchased in the latter part of last year(2010). Could this have been caused by the detergent I have been using which is an automotive shampoo? Please help I love this washer and for the times that I u


... Karcher PSI Electric Pressure Washer

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

I have a honda 2600 pressure washer. After running fine for a couple of seconds the water will stop flowing out the tip. It is receiving water,but will not flow it to the pressure hose. I even disconnected the pressure hose and no wate was flowing out. When I shut the pressure washer off it would then flow water to the hose again. Please help


This is a symptom caused by a sticking Unloader valve. The Unloader valve is inside the pump outlet body under the large black knob. \015\012Example picture : ... Honda Black Max 2600 PSI Pressure Washer

I have a Karcher K2.26 1500PSI electric pressure washer and I cannot squeeze the trigger when the water is on. I have to relieve pressure on the line to the gun to be able to squeeze the trigger. I bought this reconditioned from CPO and they are no help, even though they said it was warranted for 30 days. Help!


... Karcher K2.26 Electric Power Washer

I have a briggs & stratton pressure washer that every time I engage the spray hose my pressure washer stops. Why???? I have left it running for a couple mins. before engaging, doesn't seem to help


PROBABLY the valve that admits the water to the pump is sticking. USUALLY bad O-Rings. If the valve sticks closed, the pressure won't build up. If it sticks open, the washer will stall. Most other problems are engine problems due to bad gas, carb ... Briggs & Stratton Pressure Washers

My pressure washer is 3 years old, never had a problem with it until now. It runs for 2 seconds only on choke. It will not start or turnover at all with out the choke on. Please help, I miss my pressure washer. Thanks Andrea M. Conzet


It sounds like could be one of the problems listed below or a combination of those things.1) The exhaust is partially blocked. Check the screen covering exhaust port for carbon and dirt build-up. High-speed exhaust air must pass freely. W ... Honda Black Max 2600 PSI Pressure Washer

What oil for troybilt 020207 pressure washer - Pressure Washers


... Pressure Washers

My TroyBilt Pressure Washer 2500 PSI 2.3 max gpm will not pull detergent through the tube. I have the correct tip on the nozzle and the tube connected to the pressure washer and in the bottle of detergent but I'm getting nothing. Any ideas? Thanks! -Carson


If you follow the chemical hose back to the pump it will be attached to a barbed nipple, behind the nipple there should be an o-ring, spring and a ball.A lot of the time if you are using the proper nozzle in the low pressure setting and still c ... Briggs & Stratton Pressure Washers

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

I have a troybilt pressure washer when i crank it up it builds pressure when i engange the pressure it takes about 5 seconds and pressure goes away if i let off the trigger it will build pressure again it only has about 20 hours of use on it (i did run a acid solution through it for my driveway wonder if that ate up a seal)


Unloader valve is the most likely suspect here.\015\012Remove and clean with penetrating oil then reinstall.\015\012\015\012Also add some LIGHT oil into your supply hose via a small funnel. 3-in-1 household oil or power steer ... Pressure Washers

Troybilt pressure washer low pressure


... Pressure Washers

North star petrol pressure washer. working fine, then no high pressure, checked water feed, water filter , pressure relief valve and gun nosall well work sometimes and keep working, when you release the trigger and try in again the pressure gone again. please help, many thanks, richard


Sounds like the regulator is sticking or is airbound. loosen the water connection and then tighten it back. Could also be that the trigger gun is faulty or needs adjustment. Hope this helped ... Karcher 2500 PSI Pressure Washer

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

I have a karcher 3.80 md electric pressure washer that keeps running when not in use and the pressure is low. Any help please?


... Pressure Washers

I recently purchased a Dewalt DXPW 3835 Pressure Washer from Home Depot.... After 4 hours use I no longer get any pressure. After depressing the trigger, I get a second of pressure and then it just dies. I called DeWalt and they couldn't help and to take it to the Warranty Shop. They informed that they wouldn't be able to look at for 2 weeks so I took it back to HD and got a new one and this one does the same thing. I'm pretty sure it's probably a pretty quick fix but no one seems able to te


... Dewalt DXPW3835 - 3800 PSI Professional Gas-Cold Water Pressure

Clean and unloader valve on Karcher hd3500 pressure washer -intermittent pressure on and off. Cleaned inlet screen. Think unloader valve is is under pressure knob? Will cleaning help?


Hi:Cleaning it is not enough. You need to make sure the o-rings are in good shape and grease it with a very very good waterproof grease. ... Karcher Pressure Washers

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

I have a tpw 2200 pressure washer that has lost high pressure. i have low pressure but not high pressure.rn The machine i have is a titan tpw 2200 if some body can tell me what is wrong please help. Thank john


Pour a large amount of liquid TSP into the fresh water inlet where the garden hose connects and let is sit for a couple of days.\015\012This is how I fixed my pressure problem ... Pressure Washers

I left my craftsman pressure washer (the big one) running while i went for detergent. The pressure hose blew off and now the threads are stripped. can u help me?


You have more problems then just a stiped thread. the machine shouldnt be producing that sort of pressure if you dont have the trigger pulled.sounds to me like the pressure switch is faulty ... Pressure Washers

Have a troy built pressure washer and the gas is leaking out help


The float is stuck you can either take it apart and clean it or you might get by by just tapping lightly on the fuel bowl on the bottom of the carburator to unstick the float ... Pressure Washers

Have a troy built pressure washer and the gas is leaking out help


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1274 seconds