Having problems with your Briggs & Stratton Pressure Washer Projectpro Spray Nozzle ?

Briggs & Stratton CleanShot model 020206-0 - Low pump output

\015 I have a Briggs & Stratton CleanShot model no: 020206-0 with very low pump output. The engine starts and runs fine. I have water flow through the pump and fair dicharge volume and pressure when operated without the pressure nozzle and hose but very low output when nozzle attatched. Both of which have been checked for obstructions. Also when engauging and releasing the trigger you can hear the engine speed change momentarily from the pump load. Any suggestions? Thanks in advance...\015

Answers :

Repair Help & Product Troubleshooting for Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Briggs & Stratton CleanShot model 020206-0 - Low pump output


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

I have a leak from the pressure washer output manifold and sears model 580752050. (pump model mtpv93517) The check valve kit Briggs and Stratton # 193806gs I ordered was correct from but the check valves are too tall to seat into the output manifold and be flush when reinstalling. Did I order the wrong check valve kit or is there another problem?


... Pressure Washers

I have a Briggs Stratton Model# 020228 Gasoline Pressure washer with a Faip Brand Pump. The engine starts, the water supply goes thru the pump under its' own pressure. When I pull the trigger on the handle, there is not increase of force nor does the pump engage. I had this same problem several years ago and sent it to a dealer for service. His service tag indicated a stuck unloader. Where is the unloader located on this pump. The indentification on the pump is MTPV90736 191693 Order # 52


... Briggs & Stratton Pressure Washers

My briggs and stratton pressure washer model 020206 runs but no water thru the gun..what could it be?


... Pressure Washers

Campbell Hausfield Pressure washer model 1549. After a few years of storage, I cannot prevent the powerful spray leaking from the connection between the Gun and the Lance. I replaced the O-Ring, and tried other means unsuccessfully. Spray from the joint is almost as powerful as spray from the lance nozzle. The Briggs and Stratton engine has been cleaned and operates well. The pump operates well. But the lance connection refuses to seal.


Hello,Most likely, the housing has split and seal is not being made. There is a chance that the hose is leaking where the fitting is crimped on (my experience, but different pressure washer). Are you able to see a leak when turned off b ... Campbell Hausfeld Pressure Washers

Power washer Briggs & stratton model 2200 from sears. Just pulled out of my shed. Runs fine but water pressure is really low. I cleaned everything that may be blocked. Water pressure from house is ok.. I'm lost Help thank you.


... Pressure Washers

My briggs and stratton pressure washer model 020206 starts and runs good but no water pressure coming out of gun...any solutions?


... Pressure Washers

NO water pressure. I have a Briggs& Stratton Model 020274


... Pressure Washers

The Hom Model No. 308653045 gas-operated cold-water pressure washer has a spring-loaded control on it and I am assuming that this control regulates the output pressure of the water from the pump . . . for example, 1500 psi to 2700 psi. Is it correct to assume that this control regulates the output pressure of the pump. If the control is a pressure regulator, how does one use it and, EVEN MORE IMPORTANT, can one under-adjust or over-adjust the control to a point where THE CONTROL OR THE PUM


... Homelite Pressure Washers

We have and older Jackson model 10 AB at church, used 10 to 20 times per year. The pump motor quit this summer and was replaced by a local appliance service company. About $700 job. Upon using it recently, the first time since the new pump was installed, the RINSE cycle seems very anemic, that is, low volume and low spin rate. The dishes were not completely rinsed. Temperature was correct, 185 degrees. The service person came back to look with no improvement and now the Heaters will not co


Sounds like a wiring problem but it is controled by a thermo to make sure you get to the proper tempt . so ck the connections and mke sure the thermo is good . . and the element is good . ..hope this helps mm . ... Jackson 10A Free-standing Dishwasher

Pump is pulsating , not pumping full pressure , water supply and screens checked out ok pump model sjv3g627-1 on a briggs 6.5 hp


Pulsating is usually due to a leak. It could be the pump leaking or the hose, gun or wand leaking. Is there water coming out of these anywhere it is not meant to? It could also be a valve is not closing properly or a seal needs replacin ... Pressure Washers

Honda 11 hp, model GX340, Cat pump model 5DX40GL; Low on hydrolic oil need to know what type of hydrolic oil to use.


... Honda Pressure Washer PSI 3000

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a murray lawn mower powered by briggs and stratton, i'm trying to fing a manual on the internet but it says to put my model number, and on my engine it says that my model number is lev100 but nothing on the internet comes up, i need help. it also has a date (1995-1998). i don't know how many horse power it is.


The model numbers on a briggs engine are stamped into the metal cover above the spark plug and are the first 6 digits the rest are engine codes and type. ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

I will have low water pressure supply from source. how do i adjust for this? model GX200 with model Annovi Reverberi xtv 3g.22 pump


Low water pressure from source is generally not a problem unless water hose to washer collapses when use. You only need to supply the pump just 3 to 5 gallons of water per minute. Easy to check. Just open water supply to hose and captur ... Honda Pressure Washer PSI 3000

Troy- Bilt pressure washer #020209 , 7.25 Briggs & Stratton, AR water pump #SJV 3G27-1. Boggs down an cuts off acts as if motor is getting tight with wand in use or not. After shut down its easily starts up an repeats itself. Removed pump motor runs fine.


... Briggs & Stratton Power Products 1539 Pressure Washer

Briggs & Stratton 2300 PSI 6.0HP EXVRB2321 Pump


The cause could be 1 of two problems:1.) The seals are worn out or broken. IF you remove the head of the pump and find the broken seals, they can be replaced with this kit: ... Pressure Washers

Briggs stratton 2700 psi 2.3 gpm pump 311553gs


... Pressure Washers

Briggs and stratton generac pressure washer not getting high pressure model 1908


... Briggs & Stratton Briggs Stratton 2000 Psi Pressure Washer Freeshp

Briggs & Stratton WAP 9300P pressure washer pump oil brand


... Briggs & Stratton Pressure Washers

I have a Briggs & Stratton pressure washer, Model # 20292 (True Bilt 2200). I have no problem getting it to turn over and it will run for 3-5 seconds, but then die. Any suggestions.


If #1 doesn't work, the ports in your carb could be clogged. I just dealt with this problem this weekend. This is a relatively easy fix. Locate your carburetor and find the aluminum bowl underneath. On the bottom of the bowl, you'll find a bolt. ... Briggs & Stratton Gas Pressure Washer 20244

I have a Briggs and Stratton power washer Quantumpower 5hp water driver series 1750 PSI 2.0 gal min model # WGV1721 . I got it used and it was always a bit hard to start but always started. Pull cord frayed and broke I bought new cord and a neighbor replaced for me. Now it does not want to do anything when pulled. I can't get top cover off that has screws with round holes instead of phillips or standard slots to get to pull cord winding


Spray well with WD-40 or similar, and take a small chisel, on it's edge, and hit hard enough to allow chisel to dig in to head of screw, making a "V" like slot in the head, then angle chisel slightly and start tapping in direction of loosening(counte ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

How do i set the timing on a 6hp briggs and stratton pressure washer? mODEL g23


The only timing is the flywheel key and the air gap on the ignition coil. Air gap should be 0.010-0.012" ... Briggs & Stratton Pressure Washers

Need manual for a model 050032 generator - Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Where do you find the model number on a elite series 6.75 hp 2450 psi briggs and stratton pressure washer?


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1055 seconds