Having problems with your Briggs & Stratton Pressure Washer Projectpro Spray Nozzle ?

Oil in carb

\015 Turned upside down\015

Answers :

Repair Help & Product Troubleshooting for Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I had gas problems cleaned the carb,brass tube,filter many times. engine would start run for 20 to 40 sec.start to hunt than stop oil is new at correct level even unplugged the level device, the same results. ordered a new carb. installed it same results taken cap off tank to check if it is not a vent problem.I have tried everything, HELP


Try to start it and then start spraying with it to make sure that your pressure relief valve is working. My son-in-law had this problem and it was because the pump built up so much pressure that the engine couldn't overcome it and it would stall out ... Honda Pressure Washers

Gas got into the oil through carb. changed oil. rope won't pull. 13hp briggs on a generator.


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

I have a Baldor 6000W generator with a gx340 11hp engine. I have drained the tank and carb and put new gas and sea foam in it. Also I have replaced the spark plug and fuel filter. The engine will start/run as long a I spray starting fluid in the carb. But it will not continue to run without it. Also I just checked the oil level and that is good. Please help!!!


It sounds like the engine is not getting enough fuel for it to run. First check that you have the fuel tap in the on position. If the fuel tap is on then the carby might be blocked or the needle & seat are not working properly. Turn the ... Honda 8 HP Engine

I'm using a Dewalt 2800 power washer and someone set it on its side. And now it will not start. The air cleaner is full of oil. I think there is oil in the carb. I took the air filter off and almost get it to start. Any help?


Take the air filter off and wash in petrol.allow to dry,and put back on. then take the fuel bowl off and clean.turn fuel tap on and drain fuel from carby for a few seconds.turn fuel tap off.put fuel bowl back on.then take spark plug out and turn moto ... Dewalt 3800 PSI Pressure Washer

I have a 7 hp B&G craftsman Pressure washer , if I place an air filter on it ,it wound't start or run , if I remove the air filter it would run like a champ, but after 10 mints , oil would shoot out off the carb like a running faucet , why is it not running with the filter on,.Now am not so sure if the air filter is the correct size , because when I put it on it seem to be a bit on the taller size rather than a perfect fit, thanks for your help , in Hollywood , Reinaldo Roman .


First,It sounds like the air filter is full of dirt preventing air from flowing through, starving the engine of air.As for the oil shooting through, are you certain the oil is coming from teh carb?. Makes no sense the engine w ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Karcher hd 2500 ... starts up great, but when handle is engaged it surges and cuts out. i have cleaned carb, in line water filter, checked the oil. Any ideas?


... Karcher 2500 PSI Pressure Washer

Karcher 2400R I have not used my pressure washer for 6 months. It was left full of gas in the garage. I tried to start it but it would not fire up so I change the gas, oil, and spark plug, took apart the carburator and cleaned it out with carb cleaner. I went ahead and put everything together, pull the cord and wanted to start. While trying to start it after I sprayed starting fluid in the air cleaner I noticed that gas was coming back from the crankcase breather hose into the air filter choking


You have a poor signal to the spark plug usually caused by a rusty fly wheel found underneath the pullcord casing. clean it with releasing ajent such as wd 40. common when not in use for a while. ... Karcher 2500 PSI Pressure Washer

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a excell 2500 psi max honda 5.5 ho vr2522 2.2 gpm presser washer and has been stored for about a year, still looks brand new and has only been used twice before, it has oil and was stored with no gas in the tank, i put fresh gas in the tank and blead the fuel bowl until fuel ran out like it should, the washer wont start, ive checked the turn on switch as well and the fuel cut off knob, i spayed gas in the carb and it fired up but stopped running as fast as it began to run, its not getting


... Honda Black Max 2600 PSI Pressure Washer

Pressure washer will not stay running. Have put in new fuel, new plug, new oil. Will not start until I spray some ether in carb, then it will start and run for about 3 seconds, then stall. will not restart without another shot of ether. What should I try next? thanks


... Briggs & Stratton Gas Pressure Washer 20244

Motor will start on choke setting and then it immediately dies when moving the choke lever to the run position. Cleaned carb, new plug new air cleaner and checked all linkages. the motor has new oil and runs rough on choke like it should. any help


You say you cleaned the carb. If you did that by spraying cleaner in through the choke, that's good, but it doesn't get to the root of the problem. The problem is getting the gas into the carb. Try this. drain the gas. Put a small amount of c ... Honda Pressure Washers

Gas leaking from carb on Briggs and Stratton engine


`v already answerd this,are you slow? with oil in the sump you can do no damage by running the engine with abit of smoke,it will clear up very quickly. i find it hard to believe youhave done the things you claim if you dont know what a carby bowl is! ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

It looks like gas getting into the crankcase oil,


Here`s the go ,good possibility that you didn`t turn the gas tap off at the last time you used it.If the needle isn`t seating properly the gas wii over flowinto the carburetterif the inlet valve is open ,fuel can ,if the macine is on uneven ground ... Karcher 2500 PSI Pressure Washer

Replace oil seal GCV160


... Honda Black Max 2600 PSI Pressure Washer

Sca petrol pressure washer just stopped. How does the low oil switch work?


... Pressure Washers

I have a keihin carb on a honda engine, used on a power washer, that only runs with choke fully engaged. I have taken the carb apart and cleaned it thoroughly to no avail. the part # on the carb can't be found online. I don't know enough about carbs, theory of operation, to continue and can't find a technical ref for the keiwin being used, any suggestions as the only # on the carb yeilds no hit on the web. # stamped on carb is 65bbkf7


... Honda Pressure Washers

Have a PD2800 that has started to leak oil. lowered the oil level slightly but it started to again leak oil after just a minute or two of running from a cold start. Oil seems to be coming either from around the oil drain plug or from underneath the motor mounting plate. any ideas? Richard


Hi,There is a nice Troubleshoot article :-http://www.the-power-washer-advisor.com/pressure-washer-pump-repair.htmlHope i helped you.Thanks for using "Fixya". ... Dewalt Pressure Washers

I have a sears pressure washer, model 580752300. The pump on the underside vibrated lose and broke a couple screws. It came off and the oil drained out. I replaced the screws and it's ready to go except I can't find out how much replacement oil to put back in. Sears has larger containers but won't tell you how much oil to put in. However, there's a pricey pre-measured container they want to make you buy. Anybody know how much oil goes in that pump?


... FAIP Non Marking Pressure Washer Hose 4000 Psi, 50ft. Length

I borrowed my nieghbors power washer. It worked the first day all day. In the morning i filled the gas with a fuel stabiler, and 30 oil. I may have over filled it. Upon turning it on the oil started leaking from the air filetr compartment. It starts, but then smokes starts to fume and all the oil leaks. Did I break it or is it a easy fix. I cleaned the filter housing. Also the filter was soaked with oil. should i get a new filter and install it or what is the solution. need help.


You will need to get a new filter, and drain some of the oil out of the machine. If you over fill these this will happen. 90% of the time nothing is broken. ... Karcher 2500 PSI Pressure Washer

There are 2 different places to add oil to my 3500 Honda engine pressure washer (cold). Do I use SAE 30 for the motor oil and gear oil for the other oil?


You can use sae 30 in the motor and hydraulic oil or gear oil in the pump.\015\012just note that there may be two oil filler holes on the motor. ... Honda Landa PG 3500 PSI Pressure Washer

I just purchased a RMV2.5G27D Universal pump. Installation was easy, but I have two questions. 1. No where in the booklet does it say to put oil in it, does it come with oil already inside? There was no oil in the box but the instructions kept refering to 2.2 ounces of oil. 2. It had a red plastic plug opposite the water intake, included was a brass plug that fits into that area, does the plastic plug stay or do I put the brass plug in it?


The red plastic plug comes off, that is the plug that is only used for shipping. You should have got a ventable oil plug to replace that one in the box. The oil you would need is this ... Annovi Reverberi RMV2.5G27D Pressure Washer Pump

Honda GX 240 on woodsplitter stopped running. Tries to fire a couple of times each pull but dies. Found debris in gas tank. Cleaned out the tank and hose to carb. Cleaned out the sediment cup. Cleaned out the rust and debris from the bottom of the float bowl. sounds like debris in carb jets? Is it worthwhile taking the carb apart and cleaning it, or just order a new carb?


Install a new plug, and make sure your gas mixture is not to rich, And you air cleaner is clean ... Honda 8 HP Engine

I got the pressure washer started - lots of smoke etc after not having used 3 years. I then poured in wrong oil to top it off - my brother's chain saw bar oil. DARN. After 3-4 minutes it started rattling and stopped. Can't pull the chord to get started. Did it seize the engine? I have drained all oil. Can I try using a cleaner, light weight oil to try to unlock it?


Nope! you have blown the seals and most likely the cylinder is full of water. You will need to take it to the repairer to have it cleaned checked and new seals fitted. $200 ... Karcher 1750 psi Electric Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0151 seconds