Having problems with your Briggs & Stratton Pressure Washers ?

Engine starts but immediately quits.

\015 Suspect fuel delivery problem. Primer works fine but no additional fuel comes up from the tank. Tank was dry when I looked this spring. Sprayed carb treatment into empty tank and carb. Put fresh fuel in tank but problem is still same. Thoughts.\015

Answers :

Check the float or needle and seat valve inside the carb. One of those is probably stuck. If its a vacu-jet carb then check the diaphram on the side of the carb. It would be a small plate held on by 2 to 4 small screws. A stiff Diaphram means that it wount pump fuel.
Repair Help & Product Troubleshooting for Briggs & Stratton Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Engine starts but immediately quits.


Check the float or needle and seat valve inside the carb. One of those is probably stuck. If its a vacu-jet carb then check the diaphram on the side of the carb. It would be a small plate held on by 2 to 4 small screws. A stiff Diaphram means that it ... Briggs & Stratton Pressure Washers

I have a Troybuilt pressure washer which has a Honda GC160 engine. The engine starts easily but quits after about a minute. One pull and it re-starts, then quits in a minute....... This goes on for as long as I want to keep re-starting it. Anyone know what it might be? I pulled the carb off and blew out all of the various ports I could find. I did not remove the carb adjustment screws as I have not had any luck getting them back in place during previous problems with other gas engines.


... Karcher 2500 PSI Pressure Washer

I have a older simpson 3000 power washer, 11 hp honda,been a great machine, owned since new, seems like the pressure is building up to a point where it has blown 2 hoses, i turned the throttle down and started to wash, engine quit after about 15 min. it restarted and quit again, tried starting fluid , nothing, what might be the issue


... Honda Pressure Washer PSI 3000

Engine starts easy. engine revs up and down but does not maintain a constant. Preasure tries to come up and then quits. the governor eeps moving back and forth. I have cleaned everything including the unloader. I used lithium grease on the o rings and still it does the same. Could this be caused by bad gas, even though it starts and runs very easy


Hi And welcome to FixYa. I am Kelly I doubt that it is caused by bad gas.-It can be caused by a dirty float bowl nut or a restricted orifice in the bottom of the carburetor venturi. - Also a broken or very worn governo ... Karcher 2500 PSI Pressure Washer

I HAVE A BRAND NEW TROY-BUILT 2600PSI pressure washer. I have used it twice for about 1/2 hour each time. It worked perfectly. I tried to use it today with everything hooked up perfectly. The Honda engine started perfectly; how ever when I squeezed the wand trigger, the engine instantley died. I let the engine warm up and slowley pushed the choke in. I let it warm up for plenty of time; but everry time I squeezed the trigger it instantly quit- it even backfired once before dying. I changed the g


Sounds like the governor is stuck. My pressure washer speeds up when it has to pump. Don't know if yours uses vacuum to trigger governor or direct linkage. Good Luck. ... Psi Blue Max 2200 High Pressure Gas Power Washer

EX-CEL PRESSURWE WASHER MODEL EXH2425. HONDA 5 HP GC160 ENGINE. THE ENGINE STARTS EASY. RUNS WITH GREAT HIGH PRESSURE. WHEN WAND IS RELEASED ENGINE WILL QUIT IN 30 SECONDS OR LESS.


... Devilbliss DeVILBISS Devap DVH2600 Gas-Powered Pressure Washer

Engine starts runs good for 2 or 3 min the quites, will start right back up and run for 3 or 3 minutes, then shut off, will restart and run for 4 or 5 min then shut off.,


... Pressure Washers

STARTS AND RUNS FINE BUT WHEN I START WASHING IT QUITS SPRAYING AND THEN BUILDS PRESSURE AND KILLS ENGINE


The reason it stops spraying might be a clogged gun, hose or nozzle-tip.\015\012The reason for pressure buildup killing the engine might be a stuck unloader valve in the pump.\015\012\015\012While you are checking each component of ... Honda Pressure Washer PSI 3000

I can start it but then it quitsi i have a troy bilt honda engine power washer that will start but then quits what am i doing wrong


Sounds like the fuel pump which are made cheap. Temporarily mount gas tank up higher should do the trick. I hung my tank on handle, to lazy to replace pump so left gas tank hanging works fine. ... Karcher 2500 PSI Pressure Washer

ENGINE STARTS BUT QUITS RUNNING AFTER ABOUT A MINUTE


... Honda GCV160 5.5HP 2300PSI GAS-POWERED POWER WASHER

Engine quits running after start


It can be probably the spark plug,change the spark plug. ... Honda Pressure Washer PSI 3000

I have a mid 60's 6 hp Tecumseh engine on a Troybilt tiller. I used it to till my front yard and it ran fine. I let a friend use and it quit on him after a few minutes. It will not start. It has spark at the spark plug. I have thoroughly cleaned the carburetor by taking it apart, soaking it in cleaner, blowing out all holes and passages. I made sure the tiny holes in the power valve at the bottom of the fuel bowl are open. I have taken this carburetor apart five or six times over the years an


... Karcher 2500 PSI Pressure Washer

Have a 2400 karcher press. washer engine starts runs fine for 15 sec . then quits .I walk away and come back in 10 minutes does same thing. Checked tank and it is not plugged. Appears to have vacuum fuel pump. could that be problem?


It sounds like the fuel bowl is not filling quickly enough. Turn the fuel tap off. Then take the fuel bowl off the carby. You will see a plastic float. Above the float is a needle (small pin like) that should shut the fuel off & let it run also. Turn ... Karcher G3025OH Pressure Washer

I have the karcher 432 model and was using the round attachment to clean my paving.I then swopped for the nozzle and at this point i lost pressure. I also noticed that the engine started to vibrate quite loud and this has not stopped.


It sounds like the engine is broke ... Karcher Pressure Washers

My briggs and stratton pressure washer starts up fine but when in hit the trigger the engine cuts off immediately, does anyone know what could be causing this?


... Briggs & Stratton Pressure Washers

ENGINE STARTS FINE BUT ALMOST IMMEDIATELY DIES, CLEAN PLUG & NEW GAS APPEARS THAT IT'S NOT GETTING ANY GAS BUT CHECKS OUT OK


You may have some condensation trapped in your carburator. I don't know about your make and model, but small engine 101, gas and spark ought to make something happen. If you have good gas and good spark, there's something denying the gas access to th ... Pressure Washers

I have a Coleman powermate clean machine pressure washer 2500 psi 2.36gpm and has a 6x200 honda 6.5 horse motor. I just bought at a garage sale.It started just fine when I got home and in less that 2 minutes quit. It says the engine will stop automatically when low on oil. what kind of oil should I use and for the pump what kind of oil do you use?


... Coleman Pressure Washer PW0881800

Unable to start gas engine on a NorthStar pressure washer


Disassemble and clean the carb. If it ran briefly with the starer fluid then gasoline is not coming through the carb. ... Northstar Pressure Washers

Home Depot has a lawn mower with the Honda GCV160 Electric start version engine. They also have a pressure washer with the Honda GCV160 engine. I have a disability that makes it difficult to pull the starter rope. I would like to get the electric start on the pressure washer. My local Honda bike shop service center said they use different blocks. Can I get a pressure washer pump mounted to the Honda GCV160 Electric start version engine? If necessary, are there adapter plates that can be purchase


... Karcher 2500 PSI Pressure Washer

Hard starting 6hp Briggs and Stratton power washer engine. I poured a teaspoon of gas into the cylinder; reinserted the spark plug and with one pull in ran fine. This is a choke start engine and it may take 12 to 15 pulls to start on a cold engine. The unit is clean. The air cleaner is new. The spark plug is new. The unit is 2 years old with very little use.


Hello. I have this same machine. Go to the auto parts store and get an aerosol can of starter fluid. Have a helper squirt some into the air intake while you start it. Then continue to squirt a little starter fluid as it runs for the first two mi ... Campbell Hausfeld Pressure Washers

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Engine will start with the choke fully on, will then die


... Pressure Washers

The engine starts just fine. Everything goes okay until I pull the trigger on the spray gun and then the engine stalls out within 2-3 seconds after the water starts coming out. It is a 2700 Briggs and Stratton engine.


One thing I have found about pressure washers...you need to run water through the hose and everything until you get all the air out...or they will bog down and such until the air is out. ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Hello, I own a Honda Pressure Washer (Porter Cable Model) with a Cat pump 2600psi and 6.5 hp. An Excellent machine for the past 7 years. Last fall I noticed it was not producing the full pressure but still Engine was running strong. This past weekend. started it up and used it for about 1 hour still with minimal pressure at full throttle. Then pressure was totally cut off. I stopped and started the engine the engine and it had minimal pressure again. Same thing happened again. I stopped the engi


... Honda Pressure Washers

Won't start I have checked the spark plug and I have good saprk. I have checked the fuel sysstem and the primer bulb injects fuel. I have removed the head and cjecked for engine damage and all cycle correctly. Vaves opne on time piston shows no dmagae. side walls are smooth and not damaged. This engine was working fine but the pressure washer needed some O rings replaced. I have tried to start it with and without the pump attahced. Evrything on the engine looks fine. I removed the spark plug and


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0984 seconds