Having problems with your Briggs & Stratton Pressure Washers ?

Troy built pressure washer engine timing

\015 Replacing piston in a troy built pressure washer 020207 2200psi, need to know how to set the timing. Crank and valve gear are out of engine.Thanks\015

Answers :

Repair Help & Product Troubleshooting for Briggs & Stratton Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I HAVE A BRAND NEW TROY-BUILT 2600PSI pressure washer. I have used it twice for about 1/2 hour each time. It worked perfectly. I tried to use it today with everything hooked up perfectly. The Honda engine started perfectly; how ever when I squeezed the wand trigger, the engine instantley died. I let the engine warm up and slowley pushed the choke in. I let it warm up for plenty of time; but everry time I squeezed the trigger it instantly quit- it even backfired once before dying. I changed the g


Sounds like the governor is stuck. My pressure washer speeds up when it has to pump. Don't know if yours uses vacuum to trigger governor or direct linkage. Good Luck. ... Psi Blue Max 2200 High Pressure Gas Power Washer

Troy built pressure washer engine timing


... Briggs & Stratton Pressure Washers

Troy Built pressure washer starts up fine and idles nice. Start spraying and everything is fine for about 30sec to 1min then the engine just shuts off. Seems like pressure is building up and choking the engine out. If I dont spray it will idle all day long. I have cleaned the unloader area, still shuts off. I have the pump off the machine, what should I do? Model number 020208 Troy Built. Rev # 01


... Pressure Washers

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244

Hose lost pressure every few min. won't hold pressure for very long on a briggs and stranton pressure washer gas 6.5 engine troy built


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

I have a troy built 2450 pressure washer. The engine runs fine but I have no pressure out of the hose. Does the pump require that you put oil in it?


Do you live where it is cold in the winter? And did you winterize the pump this past winter if it is cold? They need to be winterized or pump damage can occur. ... Pressure Washers

Was using pressure washer (Troy Built 2600psi Honda engin 5.0 GC160) when it just stopped! tried to pullstart and flywheel wont turn. any ideas


... Karcher 2500 PSI Pressure Washer

I have a Troy Built 2500 PSI pressure washer with Honda 160 CVG motor. It won't start. I've replaced the gas and spark plug. Every time I pull the spark plug out it's soaked. Not sure


... Pressure Washers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

Have a troy built pressure washer and the gas is leaking out help


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Have a troy built pressure washer and the gas is leaking out help


The float is stuck you can either take it apart and clean it or you might get by by just tapping lightly on the fuel bowl on the bottom of the carburator to unstick the float ... Pressure Washers

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started.


Ok I wasnt satisfied w/ the previous answer so I did some digging. I took off all the hose attachments and drained the line. I then checked for any clogging in ALL the screens. As usual the wand screen was clogged. this is an easy fix w/ a safety pin ... Pressure Washers

Troy built pressure washer will not run unless the choke is out


... Pressure Washers

I have a mi-t-m pressure washer in the ca-series.The problem is the motor shuts down at times with out any reason. The first time I used it was on a house with a well supplied water. It worked fine,brought it home where I used it with no problem. It was used twice that first year. I then winterized it.The second year brought it out to the same house,I was using it for about a half hour when it just shut off with out any notice. I noticed there was back pressure in the engine when I tried to rest


Mi-t-m pressure washers have a Low Oil shutdown feature that turns off the motor, this is often causing similar problems on this kind of appliance.Have oil checked, if oil is fine , then the sensor that controls oil pressure and activate ... Pressure Washers

New honda pressure washer maybe had it 2 years and only has about 3 hours on it, I was using it yesterday and it started fine and after running for about 10 min it shut down like i turned the kill switch, it has oil and gas but seems to have lost compression. It is a Honda overhead cam GCV 160, pressure washer is a Troy Built model


... Pressure Washers

Troy built pressure washer won't start. It has a Honda 160 CVG motor. I used it for about a year and then it stopped working. I've replaced fuel and spark plug. Spark plug is soaked every


... Karcher 2500 PSI Pressure Washer

2550psi Troy bilt with Briggs engine. Pressure washer runs ok and builds pressure. But, when the nozzle lever is depressed the pressure is strong and then drops to a much lower pressure and a fine spray.


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers

Troy Bilt pressure washer 2600psi. Engines running fine with supply line, wand, and pressure line hooked up but no water or pressure is coming from pump. pressure line is limp. What is the problem?


... Troy-Bilt Pressure Washers

Troy built pressure washer model 020209


... Briggs & Stratton Pressure Washers

Troy Built Pressure washer


... Pressure Washers

NO water coming out troy built 2200 pressure washer


Did you install the key on the flywheel ... Pressure Washers

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.


This is a piston seal issue. You can get a kit to rebuild the pump. ... Comet AXD 3020 G Pressure Washer Pump

Won't start I have checked the spark plug and I have good saprk. I have checked the fuel sysstem and the primer bulb injects fuel. I have removed the head and cjecked for engine damage and all cycle correctly. Vaves opne on time piston shows no dmagae. side walls are smooth and not damaged. This engine was working fine but the pressure washer needed some O rings replaced. I have tried to start it with and without the pump attahced. Evrything on the engine looks fine. I removed the spark plug and


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1197 seconds