Having problems with your Briggs & Stratton Pressure Washers ?

Not much pressure,after building pump

\015 Craftsman 3.8hp lavorwash 1500 pump pressure washer,did rebuild kit,an bearing on it,problem is 300psi to 600psi on 1500psi unit need help?\015

Answers :

It sounds like one of the pressure valves is leaking
Repair Help & Product Troubleshooting for Briggs & Stratton Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

Not much pressure,after building pump


It sounds like one of the pressure valves is leaking ... Briggs & Stratton Pressure Washers

No pressure i have a karcher g 2600 vh i wasnt getting pressure and i found that my spill valve was faulty it was actually broken i bought a new one installed it and im still not getting much better pressure ive taken the pump apart and checked for build ups blew thru the valves wirh the compressor and there appear to be no blockages


... Karcher G 2600 VH Gas Pressure Washer

Builds up to much pressure in hose and stalls engine


Sounds like the unloader is not working. try replacing it and see if that helps. ... Campbell Hausfeld PW2102 Gas Pressure Washer

My karcher 3100 professional pressure washer build pressure at random, when I take the nozzle of the gun the pump works when the nozzle is on the pump wont build pressure or if I hold the gun in an on possition after 5-7 min it build up the pressure, what is wrong?


... Karcher Pressure Washers

I have a sears pressure washer, model 580752300. The pump on the underside vibrated lose and broke a couple screws. It came off and the oil drained out. I replaced the screws and it's ready to go except I can't find out how much replacement oil to put back in. Sears has larger containers but won't tell you how much oil to put in. However, there's a pricey pre-measured container they want to make you buy. Anybody know how much oil goes in that pump?


... FAIP Non Marking Pressure Washer Hose 4000 Psi, 50ft. Length

Pump leaks not to much pressure and when i you the prime pump


Hello rr61If the pump is leaking you will not get pressure. You need to get the leak fixed. Where is it leaking from?Leaning back to star and run sounds like the motor oil is low. You are "tricking " the low oil sensor. I would change ... Briggs & Stratton Pressure Washers

Pumpoil started to leak out after a few hrs of use. i have pump oil that i originally got over 12 yrs ago with the pump---is that unopened can still good? and how do you add and how much pump oil do you add? thanks----gary


12years doesn`t have the effect on oil that it does on women,so you should be right.has the machime ever done this before?is the oil white?i think you should drain the oil completely there will be an indicater the some where to tell you how mch,I don ... Pressure Washers

HI, I have a Karcher Model K2400 and the pump stopped working. I took it apart and found the 'cheese head' screw had broken. there didn't appear to be any other problem with the pump so i am replacing the screw only. my question is how much pump oil should be put in the reservoir upon assembly as there doesn't appear to be a fill/drain plug?


... Karcher 2500 PSI Pressure Washer

Plastic Pieces We purchased our ASKO 1385 dishwasher 7-8 years ago. Over the years, I have found "small square, thin, pieces of gray plastic" inside. Where are these coming from? Also, we have replaced the drain pump 2 years ago and looks like we'll be replaced the main pump within the next few days as no water is going through. We are looking at paying big $$$ for that pump. Almost half as much as purchasing a new dishwasher. Is this a common problem?


Yes, I have the same problem and it is the upper bearing rack, not the pump impeller. The new bearing kit is $30.00 (another is available for $123.00-the same!!). ... Asko 1385 Dishwasher

I have two questions and would greatly appreciate some help: - What oil to use in the pressure pump of a Ryobi Pressure Washer RY80030? - How much to put in? The pump model is MTP092150 from FAIP. As per the manufacturer, the oil is not to be changed or topped up by the end-user, I know, I know, but brought to a service center instead - I certainly don't want to do that, and there is none close to my place anyway. The reason I need this is that I had to take the pump apart and a


... FAIP Non Marking Pressure Washer Hose 4000 Psi, 50ft. Length

My Karcher K3.48M pressure washer remains in the low pressure mode even when I return the pressure nozzle to the high pressure position. How can this be corrected. The pump seems to build up the pressure because when I release the handle the pump motor stops. This is a fairly new pump which was purchased in the latter part of last year(2010). Could this have been caused by the detergent I have been using which is an automotive shampoo? Please help I love this washer and for the times that I u


... Karcher PSI Electric Pressure Washer

Upper & bottom arms are not turning even though the motor seems OK, pump for draining seems OK too. rcently I changed the pump kit plus some gasket and seals. My Maytag is about 14 yold and was very good for me untill I changed the parts. Could it be a weak motor pump. The water splashes very much in the machine but no arm turning!? Help me thank you Ben


Hi Ben, had the motor impellor shattered in the old pump ie-chunks broken off ? if so there is every possibility that these pieces have lodged in the wash delivery pipework at an elbow or indeed at the arm boss itself -i would try to check as much of ... Dishwashers

Noisy pump This is supposedly the quietest washing machine. It is until the pump comes into operation. It pumps incessantly for up to ten minutes before the spin operates and it is extremely noisy. I have had an Hotpoint engineer visit and he brusquely said that this is normal. I wouldn't have purchased it if I had known this. My previous Zanussi was much better. Was the engineer correct?


It depends on the design, the way it is mounted on the machine matters a lot.Sometimes pump makes noise due air trapping. Check your water flow. Add 10 liters of water in the chamber direct and close the door. start the machine in usual w ... Dishwashers

I have a model 665.1576 or 1676 my paperwork does not have the number on it and no part number on he machine, but I ordered parts from the catalog which matched. about 7 years old, stopped draining, so I changed the Seal kit, pump base seal, impeller, plus drain cover gasket but not the pump gasket could not find it, reinstalled, pump works but much slower and times out, have to hit drain button to get all water out. Keith


... Kenmore Dishwashers

AT FIRST WITH JUST THE WATER ON (PUMP OFF) I SQUEEZE THE WAND AND WATER COMES OUT ABOUT 3 FT. THEN WHEN I START THE PUMP AND SQUEZE THE WAND ONE STRONG SQUIRT COMES OUT THEN GOES BACK TO ABOUT 4 FT. NOT MUCH PRESSURE. CHECKED THE CHECK VALVES, AND THE 3 PISTONS THEY ALL WORK. PUMP NO.AXD 3020


Hi, W/D here.Leave the water on, and hold the trigger down for about 5 minutes to get all of the air out of the system. Letting off of the trigger occasionally and then opening it up will help displace any air in the chambers. While still hol ... Comet Axd3020g Pressure Washer Pump 27 Gpm 2000 Psi

Our Asko D1796 dishwasher has all lights flashing and is displaying a F2 message, which according to the good book means there is too much water in the machine. I have followed the instructions for a normal inlet time but the indicators will not change. Is it trying to tell me the Drain Pump is dead? A new drain pump was fitted three years ago. There is no eidence of water in the machine. Can anyone help? Thanks. Alan


Hi Alan,\015\012\015\012The F2 on Asko means it's sensed an overfill, that in itself though can be provoked by a couple of thing's. First, check for blockage at the end of the drain hose where it connect's to your household plumbing, be it under the ... Asko D1796FI Built-in Dishwasher

My dishwasher keeps trying to pump water out. The pump is continually trying to extract water. It doesn't make any difference where the dial is in the program. Any help much appreciated.


Make sure your drain hose from the bottom of the dishwasher goes up higher than the drain connection under the sink. if it does not this could cause a siphon problem. good luck If this is not the problem then sounds like your pump is getting power al ... Dishwashers

I have a bosch shv99a13uc. i rescued this from a thrift store so i am not sure of the history . i have installed it . all the controls work . it fills and trys to work it dosen't spray much and grinds like a very loud timer what tests should i do and can i get a manual that shows me ho to get the pump out. I think it sounds like something in the pump any help would be great Thanks


Hello &\015\012Welcome to FixYa\015\012\015\012Please check\015\012this video on how to clean the pump filter:\015\012\015\012 ... Bosch 24 in. SHV99A13UC Dishwasher

Hobart LXI you seem to know a lot about the hobart, maybe you can help me. My hobart Lxi high temp is just now out of warranty, i am mechanically inclined, and need to adjust my detergent and rinse aid pumps. How difficult is this and how can i go about doing so. Both the pumps are running too much product.


Question--As of today if you look at the display does it read add detergent or add rinse aid?Im asking you this because theres a chemical pump circuit board that senses the chemicals on this d/w.And if the d/w displays those the d/w will keep dumping ... Dishwashers

I have a honda pressure washer. Cart serial # 2151076370 cart model # 2221SCVH pump serial # 0000231983 pump model # D2150231983 The problem I am having is that it will not build pressure.


... Honda Pressure Washers

My GE Nautilus DW doesn't fully drain. When it is drained as much as it will it leaves water in the sump at the rear right. If you run the pump at that point, it sucks water out of the sump, but when you open the door and the pump stops water flows back into it. It seems like there is a check valve that isn't working. I have cleaned the sump and the screen which runs accross the rear. I also have taken the plunger out and cleaned it. Then I took the housing for the plugner off the bottom. I don'


HI. check the following areas for fualts.1. Air gap / Drain hosesIf there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: I ... Dishwashers

The Pressure Builds up the machine can't be maintained on, unless the spray gun is pressed. The pressure build up so much that it blew out a unloadervalve bolt.


... Pressure Washers

I have a model 5000g. it might have 15 hrs. total running time on it. when i tried to use it last it would not build pressure. i took the pump apart and cleaned and regreased it. everything looked good. ive got good pressure to the pump but just a small spray out the wand. when running there is no real load on the engine. it has always been kept inside in a warm enviorment.


... Karcher Pressure Washers

Water pours out the other end of the pump opposite the pressure hose connection. It has a clear plastic cap with a small **** in it. Looks like water should escape here but way too much water being pumped out.


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0744 seconds