Having problems with your Briggs & Stratton Pressure Washers ?

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


Answers :

A leaking gun will kill all the pressure. You may need to repair or replace the gun
Repair Help & Product Troubleshooting for Briggs & Stratton Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

No pressure McCullough pressure washer has no pressure after siting all winter. I took apart the assembly and the oil leaked out, also I noticed yhe o-ring that seals the two pieces together seems to have been blown out. Where can I get parts and oil. Thanks for any advice.


... McCulloch FH140A Electric Pressure Washer

Had the Northstar 3000 psi Pressure Washer for 2 months and it started leaking oil from the pump during use. Took it to Northern and they are replacing the pump under warranty but said it was likely because I was using quick connects on my garden hose coupling and that was restricting the water flow making the pump overheat. They said never to use quick connects on the garden hose unless the opening is at least 5/8". Does anyone make such a quick connect? I hate having to screw the garden hose o


It is easy to check if your hose and quick connects are supplying enough water to the pump. Your pressure washer gallon per minuite requirements are printed on the machine and also on the pressure tips in GPM. Your post indicates 2.5 gpm but check yo ... Northstar Pressure Washer 3000 PSI

Karcher K3.91, lost some pressure and pulsing when trigger is release. stripped it down and checked all six valves and there all sealing as they should. i took apart the unloader valve cleaned and inspected and thats fine. there is NO water leeks anywhere or oil. preasure washer is 2 years old and gets used once a week for ten minutes. i really dont understand why its playing up


... Pressure Washers

Karcher 2400R I have not used my pressure washer for 6 months. It was left full of gas in the garage. I tried to start it but it would not fire up so I change the gas, oil, and spark plug, took apart the carburator and cleaned it out with carb cleaner. I went ahead and put everything together, pull the cord and wanted to start. While trying to start it after I sprayed starting fluid in the air cleaner I noticed that gas was coming back from the crankcase breather hose into the air filter choking


You have a poor signal to the spark plug usually caused by a rusty fly wheel found underneath the pullcord casing. clean it with releasing ajent such as wd 40. common when not in use for a while. ... Karcher 2500 PSI Pressure Washer

Low Pressure with no hose attached, pressure is good, attach hose without wand and pressure drops 50%. Have had pump apart 10 times, have checked bypass valve, have even removed bypass and filled passage way so water could not bypass wihout any change. Am down to thinking pump casting is cracked allowing bypassing to happen. Does each of the three piston chambers have a check valve so one piston is not pumping back into another piston chamber?


I worked at a tool rental while attending college and had the opportunity to work on a variety of pressure washers, however, they were of the commercial type. Commercial washers are slightly different in that they usually have seperated components fo ... Karcher 2500 PSI Pressure Washer

Hose connections I have a McCulloch FHH18A pressure washer. Does anyone have a diagram showing where the ends of the hoses for the two tanks should be attached at the tank selector? I took it apart and neglected to make a diagram for reference.


... McCulloch FHH18A Electric Pressure Washer

Runs fine gc160 wont give me any pressure. i took the pump apart and cleaned it then put it all back together the pressure was intermediate but now nothing at all


If you give us a bit more information we may be able to assist!is it a pressure washer you are trying to get running.the number you give is the model number of the honda engine. 5.5 hp honda domestic use.what does the pu ... Karcher 2500 PSI Pressure Washer

I have a troy built 2450 pressure washer. The engine runs fine but I have no pressure out of the hose. Does the pump require that you put oil in it?


Do you live where it is cold in the winter? And did you winterize the pump this past winter if it is cold? They need to be winterized or pump damage can occur. ... Pressure Washers

Model 01902 2350 psi . engine runs fine , sprays out nozzle but lower pressure and water sprays out plastic elbow on relief valve , that is supose to **** in soap if used , cant hold finger over spray from elbow , high pressure , took apart relief valve and plastic valves all orings are ok , brass pump seals look ok , all back together , still blows out elbow . ?? plastic spools were out by somebody else , not sure if they are in right , cant find picture to compare .


It sounds as if the non return valve in the elbow is the wrong way around .The o-ring normally goes in first then the ball then the spring. Try it and good luck. ... Pressure Washers

Motor runs fine but not pressure other that from garden hose.


You have a unloader or bypass valve on the machine & it sounds like that is sticking.\015\012take out and lubricate ... RTO 1800 PSI Pressure Washer

No pressure HOSE IS BIG ENOUGH,NO KINKS, FILTER IS CLEAN. TOOK THE PUMP APART AND CHECKED ALL THE CHECKS, THEY WERE ALL OK.WHAT ELSE CAN I LOOK FOR? THE PUMP IS A KARCHER-MODEL G 1800 LB Thanks, Art


Brother Art,\015\012\015\012Try this trick; it always works for me. Assemble the garden hose to the washer, install the HP hose, turn on the water. Now, make sure that there is no air trapped in the garden hose. Manipulate so as to dir ... Karcher Pressure Washers

Coleman Powermate pressure washer. Model PW0751310 A lot of water leaks out in the handle where you squeeze for the unit to work, thus the power spray is weak at best. Took handle/arm apart and didn't see any issues. Possible "O" ring worn out (if i was looking at "O" ring. Any ideas?


There may be orings in gun but usually not available as a repair kit. Replace the gun with a 5000 to 6000 psi. You will get a much longer life by over sizing gun. If you like to tinker, you can by orings at Lowes in the plumbing department. Lube th ... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

I have a JD 3300 psi 1150 Briggs n Stratton pw. It is leaking from the oil cap/ dipstick seemingly from high pressure. The cap dipstick is about 10 inches long, so this is a real squirt goin on. There is no rubber oring or gasket in the cap. I bought it from a pawn shop new, or at least seemed new as the hose and tips were still factory wrapped. Any ideas?


Either there is compression from cylinder getting into crankcase pushing the oil out or the oil level is too high. ... Briggs & Stratton Pressure Washers

My pressure washer leaks oil out the air filter. I have removed the filter and it still pours out. it only happens when i engage thw hose.


Hi and welcome to FixYa, I am Kelly. \015\012 [ First check and make sure someone did not over service the engine oil level. ] #1 Cause of oil blow by that happens out of the blue. \015\012\015\012This is happening ... Karcher 2500 PSI Pressure Washer

Rebuilt honda GC160 5hp engine for a power washer and only got the engine to start once. Just took apart and saw that the cylinder and piston was all scored up again.


... Honda Pressure Washers

Pressure washer vent cap leaking oil


... Pressure Washers

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

I have a honda 2600 pressure washer. After running fine for a couple of seconds the water will stop flowing out the tip. It is receiving water,but will not flow it to the pressure hose. I even disconnected the pressure hose and no wate was flowing out. When I shut the pressure washer off it would then flow water to the hose again. Please help


This is a symptom caused by a sticking Unloader valve. The Unloader valve is inside the pump outlet body under the large black knob. \015\012Example picture : ... Honda Black Max 2600 PSI Pressure Washer

Assembly plans for karcher 2400 psi pressure i recently had a problem, with my pressure washer. i was cleaning out my hose and took the hose assembly and brass fitting off. run water threw it thought i had cleand it out, put it back together and now when i hooked my water hose back up the water comes out of the despencer instead of the pressure wand. does eny one no what i need to do to revurse this?


... Honda Karcher G2400HH-R Pressure Washer

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

I have a Kracher K 4000 GS pressure washer and it seems to have been fine until today. When I start it and squeeze the trigger there is nor pressure, water comes out but as it would normally from the hose. The engine does not even seem to be under load. I used it the other day and got pressure when I picnhed off the soap hose but that did not work this time.


... Karcher G3025OH Pressure Washer

I have a 2300 psi gas pressure washer, campbell hausfeld, runs fine but water comes out the nozzle like a hose , no high pressure. inlet filter is clean and when you pull the trigger on the nozzle water comes out like a hose but no pressure


If you no longer have High Pressure coming out while machine is running, it's a pump issue. ... Campbell Hausfeld PW2575 Pressure Washer

My pressure washer was running fine then bogged out.The person who lent it to me said dont worry about the oil it is fine, so i didnt check. I checked the oil and it was almost bone dry. So i filled it with oil but now it wont start, is it possible that the engine is siezed up or, can i get it running.


You probably helped destroy the engine. Honda's are great engines until they run low on oil ... Karcher 2500 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0831 seconds