Having problems with your Briggs & Stratton Pressure Washers ?

Where would I find availability of parts in QLD Australia to suit a pressure cleaner 3200 psi coupled to a Briggs & Stratton motor pressure washer number 020225-0 part required chemical injection kit FIG E on general assembly part number 192914GS


Answers :

Wayne,

Any Pressure Washer dealer should be able to sell you what is called a "Down Stream Injector". What you need to know is the flow rate. Like, at low pressure, see how many Gallons/Liters Per Minute actually comes out the wand. That is what the seller needs to know in order to sell you one the proper sized internal orifice. Also, you need to know that these devices only **** chemical at low pressure. They make special tips and/or wands so you can easily revert to low pressure to apply your cleaning chemical. This stuff is generic. It will come with standard pipe threading. Close is good enough on "flow-rate". Just use a bucket or something and get a reasonably close estimate.
Repair Help & Product Troubleshooting for Briggs & Stratton Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where would I find availability of parts in QLD Australia to suit a pressure cleaner 3200 psi coupled to a Briggs & Stratton motor pressure washer number 020225-0 part required chemical injection kit FIG E on general assembly part number 192914GS


Wayne, Any Pressure Washer dealer should be able to sell you what is called a "Down Stream Injector". What you need to know is the flow rate. Like, at low pressure, see how many Gallons/Liters Per Minute actually comes out the wand. That i ... Briggs & Stratton Pressure Washers

Just need a part number, I have a CA-2003-HDHB pressure washer and I need the part number for the valve kit. also if you could direct me to where I might find a parts breakdown online for my machine, in case I need more part numbers. Thank you. Joe G.


... Mi T M Pressure Washers

Replacing chemical injection kit on Troybilt 020292 pressure washer


... Pressure Washers

I have a Troy Built Pressure Washer Model # 01903. It has snapped a bolt off in the pump head area and is leaking H2O. What is the part number of the repair kit for this problem and where can I order it??


... Pressure Washers

I have a Troy Built Pressure Washer Model # 01903. It has snapped a bolt off in the pump head area and is leaking H2O. What is the part number of the repair kit for this problem and where can I order it??


... Pressure Washers

I have a power washer that needs a wand for the high pressure, the low pressure wand is part number PA6630GF. I need the part number and where tp urchase the high pressure wand.


... McCulloch FHH18A Electric Pressure Washer

WHAT ARE THE THERMAL FUSE SPECIFICATIONS FOR KENMORE ELITE MODEL 66513122K701SERIAL NUMBER FY1211868 AND WHAT IS THE PART NUMBER FOR A THERMAL FUSE KIT? WE HAVE HAD TWO FUSES BLOW AND THERE DAMAGE TO THE WIRING ON THE LEFT HAND SIDE OF THE CONTROL PANEL THAT CONNECTS O THE SWITCH. THEIR IS DISCOLORATION ON THE PARTS AND WIRING. WE HAVE SEEN EXPERTS STATE THAT IN ORDER TO CORRECT OUR ISSUE WITH THE FUSE BURNING OUT WE NEED A THERMAL FUSE KIT AND WE NEED THE SWITCH AND THE WIRING THAT CONNECTS TO


Http://appliancejunk.com/ge/dishwasher/31-9137.pdf\015\012\015\012A ... Dishwashers

The slide on the upper basket keeps falling out. It's been fixed twice but doesn't hold. The second repair man who put the slide back in the rollers said he couldn't see anything wrong with it, but it still didn't hold, so he called your tech dept. who said they had roller and slide kits at a total cost of $66 for this model. The slide kit had a new part number but the tech department didn't tell the repair man why they'd changed the part. The roller kit was one for dishwashers the sides o


One option is installing stainless steel washers on the rack supports that screw into the side of the tub. The rack falls down because there is too much "slop" with the rack...a couple small washers to space them tighter normally does the trick. ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a kenmore dishwasher 665.16529000. When I opened the dishwasher this am the pressure tower part number 8268862 was not connected-it was off. The exposed part is a black rubber thing. It looks like a doughnut. I can't figure out how to get the pressure tower re-connected.


The tower attaches to the bottom rack and when the bottom rack is pushed in the tower sits on top of the following part. Check for cracks in the tower. It may explain why you cannot fit it back in place.\015\012\015\012 ... Kenmore Dishwashers

I have a model 665.1576 or 1676 my paperwork does not have the number on it and no part number on he machine, but I ordered parts from the catalog which matched. about 7 years old, stopped draining, so I changed the Seal kit, pump base seal, impeller, plus drain cover gasket but not the pump gasket could not find it, reinstalled, pump works but much slower and times out, have to hit drain button to get all water out. Keith


... Kenmore Dishwashers

My Honda pressure washer is leaking out of the thermal relief valve and I am looking for a part,I also do not have the manual. The model number is WGC 3030 and it is 3.0 gpm 9.0HP. The number on the thermal valve is 33120004,where can I find a part?


Does the thermal valve just screw into the pump head, if so what size thread is it? I have 1/4, 3/8, 1/2 in stock. ... Honda Pressure Washer PSI 3000

North Star Pressure washer Model 157370C Coupler Part broken between engine and garden hose. Need new part with all the interfaces. Where can I purchase and what are the part numbers? Thanks **** McGuire ****[email protected]


... Pressure Washers

2000 epw Northstar Item # 157942E 230v 2000 psi 3.5 gal/min #5 nozzle Problem: No pressure. Motor running...seems to be in bypass. Checked starter...but not finding power to the pressure regulator. May need a new starter/relay/contactor. Was working fine..May wish to order a starter and a possibly a pressure regulator...I have photo's of the complete set up if needed. Need to know part numbers to order and what company to order from. Thanks, Greg Scott


... North Star Stainless Steel Under Car Cleaner 16in

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Hi, Karcher calls the unloader valve a spill valve, this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps ... Karcher 2500 PSI Pressure Washer

Pressure washer part plug with a b stamped cannot find part number


... Pressure Washers

I need the owners/operators manual with parts listing and parts numbers for the K'A'RCHER HDS 750 hot high pressure washer.... PLEASE.......


I found this manual but it is not free.\015\012http://www.industrialmanuals.com/karcher-series-instruction-operatio ... Karcher 2500 PSI Pressure Washer

Looking for manual for honda pressure washer,its a GX 340 11.0 HP that I can view online without buying so I can find the part and part number


Go to this page: \015\012\015\012http://www.jackssmallengines.com/help.cfm\015\012\015\012You must have your exact engine model number lis ... Honda Pressure Washer PSI 3000

I have a Karcher GCV 160 5.5hp 2500psi Model G2500VH pressure washer What is the replacement pump part number..is it 35328320 ?


Yes that is correct ... Karcher 2500 PSI Pressure Washer

Do you know the part number for the whole kit to repair the pulley/cord system that controls whether or not the door falls down when you open it?


Hello, welcome to FixYa.\015\012\015\012If you can provide the model number (usually on inside of door frame or tub frame around door opening) and make/brand name, I'll see what I can find for you.\015\012 ... Dishwashers

I require a karcher hds745 pressure washer as i cant seem to get the chemical to work


Hi, this can be a problem with the hds745 machine, there are a few different versions on the market.\015\012you first need to put a piece of pipe direct to the pump and bypass the chem valve and filter.\015\012if still no look then you wi ... Karcher Pressure Washers

Model: 1578201D PSI 4000 3.5 GPM The machine is only 2-3 years old and has always worked fantastically (with very limited usage). The inlet fitting got broken and we replaced it with a new inlet filter (part number 35169) and now it has low pressure. Is there something else we should check or replace?


Hi there,A "chattering" pressure washer pump can be caused by many things. You could have a bent or damaged inlet line, or the water supply might be too low. Fixing these is simple, but checking on the water supply is critical. Never let ... Pressure Washers

I have a Generac MC660 pressure washer with a chemical injector on it The head bolt has broken where it bolts on to the pump. Do you carry parts?


This is a Help forum but you should be able to find a service dealer from Comet. Here is a link to their web site. LINK ... Comet BXD2527 Pressure Washer Pump

I have a SMEG DWF614 SS dishwasher. I continue to get an E8 error message. The diverter valve motor turns freely & the motor turns freely when they are seperated. However, when they are assembled, the motor turns the valve & continues to try turning the valve when the valve is on its stop position. Is the motor & valve faulty or is it the control. If you can answer, what part number would I require. Regards Leighton Davies


... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

Coleman power washer PW0912201. Water is blowing out of the chemical pickup tube when water hose is turned on prior to starting. After starting the water realy blows out from there. Would the unloader be faulty? I tried to pull out the unloader stem assembly from the manifold but it appears to be pressed in. Do I need a new manifold kit? or am I looking at the wrong part to correct this?


... Coleman Pressure Washers

Hot point dishwasher model 7841a require part number for the main wiring loom from door to all main components


Doubt this is available as a spare.\015\012faults in the wiring loom where it flexes with the door opening are common\015\012usual repair is to splice the broken wires ... Hotpoint Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1135 seconds