Having problems with your Briggs & Stratton Pressure Washers ?

Husky 2600 PSI Pressure Washer low pressure tap water flows thru the pump and out the nozzel but no high pressure flow

\015 Husky 2600 pasi SN AXL-1030187\015

Answers :

Repair Help & Product Troubleshooting for Briggs & Stratton Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Husky 2600 PSI Pressure Washer low pressure tap water flows thru the pump and out the nozzel but no high pressure flow


... Briggs & Stratton Pressure Washers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

Hi ..I have an Excell gas pressure washer model no. Exwgv2121-3 with Faip 2100 psi 2 gpm vertical shaft pump..the problem is that there is water leaking from every weep hole at the bottom of the pump when running. Oddly enough,the pump still puts out significant pressure but less than it should due to the leaking water. What is the most likely cause of this?..is it the high pressure water seal(s)? If so,how do I repair it?


... Pressure Washers

I have a campbell hausfeld 2450 pressure washer with water coming out of a brass hose nozzel right next to where you screw the high pressure to the pump as soon as you turn the water on from the house, start it up and high pressure comes out of it and the hose about half pressure, any ideas?


This is called the chemical injector which enables you to insert the hose for you to dispense the soap and or chemical by utilizing a soap nozzle .apparently inside this barb you will find a ball a spring and a o-ring,find the replacement parts or ki ... Campbell Hausfeld Pressure Washers

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244

I have a Karcher G2600 OR Pressure Washer, 2600 psi, 2.5 gpm. PN 1.194 506 0. gas engine works fine and water flows fine but pump is not adding pressure to stream. Checked and cleaned inlet water filter.


... Pressure Washers

Had the Northstar 3000 psi Pressure Washer for 2 months and it started leaking oil from the pump during use. Took it to Northern and they are replacing the pump under warranty but said it was likely because I was using quick connects on my garden hose coupling and that was restricting the water flow making the pump overheat. They said never to use quick connects on the garden hose unless the opening is at least 5/8". Does anyone make such a quick connect? I hate having to screw the garden hose o


It is easy to check if your hose and quick connects are supplying enough water to the pump. Your pressure washer gallon per minuite requirements are printed on the machine and also on the pressure tips in GPM. Your post indicates 2.5 gpm but check yo ... Northstar Pressure Washer 3000 PSI

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

I have a husky 2200 psi pressure washer, the water flows freely through the unit until started, then there is no water out of the nozzel.


... Briggs & Stratton Gas Pressure Washer 20244

Model 01902 2350 psi . engine runs fine , sprays out nozzle but lower pressure and water sprays out plastic elbow on relief valve , that is supose to **** in soap if used , cant hold finger over spray from elbow , high pressure , took apart relief valve and plastic valves all orings are ok , brass pump seals look ok , all back together , still blows out elbow . ?? plastic spools were out by somebody else , not sure if they are in right , cant find picture to compare .


It sounds as if the non return valve in the elbow is the wrong way around .The o-ring normally goes in first then the ball then the spring. Try it and good luck. ... Pressure Washers

The Hom Model No. 308653045 gas-operated cold-water pressure washer has a spring-loaded control on it and I am assuming that this control regulates the output pressure of the water from the pump . . . for example, 1500 psi to 2700 psi. Is it correct to assume that this control regulates the output pressure of the pump. If the control is a pressure regulator, how does one use it and, EVEN MORE IMPORTANT, can one under-adjust or over-adjust the control to a point where THE CONTROL OR THE PUM


... Homelite Pressure Washers

Kenmoore Quiet quard 3 Model #665.74363K1 Serial #FS3502091 The unit will not drain properly. When in drain mode, it will drain slowly when diconnected from the disposal and lowerd to floor, and drains even slower at disposal level, or hooked to disposal. Disposal nipple is clear. I removed the hose and flushed it out with high pressure, found no blockages, hose flows freely and did not fix the problem. The motor is turning and seems to pump water fine, all wands are truning with powerfull spray


... Kenmore Dishwashers

Low pressure While I initially get high pressure, when I resume washing after having released the trigger, water pressure is low. By removing the nozzel tip and reinstalling, high water pressure is resored. What is happening?


If this keeps happening repeatedly it sounds like you need a new seal kit put in it can be done easily enough by you or you can get a shop to do it , if you live in a cold winter climate be sure to winterize the washer every year or keep it somew ... Karcher 2500 PSI Pressure Washer

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

Dear Sir?madam, I bought a CV-240 4 MBC HONDA PRESSURE WASHER , 2400 PSI , 5.5HP, It is 4 stoke overhead, cam single cylinder , October, 2010 from NATIONAL HARDWARE SUPER CENTRE – GUYANA. I used this equipment sparingly during this year. I have 2 – 450 gallons plastic water tanks to supply the pressure with water. Recently, water is not coming out through the pressure hose. I talked to a technician, and he opened the water pump and there is some white plastic valve, one was broken and he repl


... Karcher 2500 PSI Pressure Washer

My Karcher, Powered by Honda, High Pressure Spray Cleaner, 2600 PSI, will not pump high pressure. It has a "G 2600 VH" pump


... Karcher G 2600 VH Gas Pressure Washer

Hi have a Karcher 6.91 and I cant get any high water pressure. It has power, I have checked the o-rings, filter and lances but it does not build up high pressure. The water also appears to flow back


... Karcher Pressure Washers

It appears that there is not enough water pressure through the sprayers to to wash food 'deposits' off the plates and dishes.We have well water and it has a some what high lime content so I suspact that there is some calcium / lime clogging in the machine. I thought of removing the pressure pump to see if that is clogged up but before doing this, have you any other sugestions(i.e run vinegar through the pump? ). The holes in the sprayer . rotating arms appear to be clean.The machine has been e


The water-inlet valve lets water enter the machine. Make sure it’s not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. There is a video of this at ... Kenmore 24 in. 16032 Built-in Dishwasher

Hi have a Karcher 6.91 and I cant get any high water pressure. It has power, I have checked the o-rings, filter and lances but it does not build up high pressure. The water also appears to flow back


... Pressure Washers

North star eletric hot 2000 psi 3.5 gal per min oil pump had blown shaft seal. replaced with new pump. put small allen plug in return port. I have oil flow to the pump but none comes out port leading to burner even with shutoff switch removed and pump turning. Installed test gage 0 pressure. Took off bypass line and ran into can. pumps small amount of fuel into can that way but with uneven flow & small bubbles. nomatter what I do I just can't get fuel outlet port to burner. pump # A2VA-7116 pl


... Northstar Pressure Washers

I have a Dewalt 3800 pressure washer fitted with a 67DX39G11 pump. Started unit up for the first this year, has pressure for 15 seconds then nothing. Water is flowing through okay, everything seems in order but no pressure. Unit is 2 years old but has only 15 hours of total running time. I think the pump has failed, is it normal for a pump to fail with only 15 hours on the clock?


... Dewalt 3800 PSI Pressure Washer

I have a Briggs Stratton Model# 020228 Gasoline Pressure washer with a Faip Brand Pump. The engine starts, the water supply goes thru the pump under its' own pressure. When I pull the trigger on the handle, there is not increase of force nor does the pump engage. I had this same problem several years ago and sent it to a dealer for service. His service tag indicated a stuck unloader. Where is the unloader located on this pump. The indentification on the pump is MTPV90736 191693 Order # 52


... Briggs & Stratton Pressure Washers

Cat pump 3200 psi problem- plz help! I hook up the hose and no water will come out of the pump out let with or with out the hose the pressure waser hose hooked up!


... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1692 seconds