Having problems with your Briggs & Stratton Prosumer 20324 Gas Pressure Washer ?

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


Answers :

Repair Help & Product Troubleshooting for Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

Pressure Washer I have a Porter Cable pressure model no.PCH2401.It works fine for 5 minutes,then I can hear the motor loading down and then it stalls out. I tried to start it and it was very hard to pull on. disconnected the water supply and if was very easy to pull and started right up. I noticed the pump was very hot.This unit has a thermal relief valve on it,shouldn't it have released when it gets to a certain temperature .I was thinking maybe this is why it might be shutting the motor


Any leaks from connection at pump to gun and wand assembly if so the valve is detecting leakage and open up again without u squeezing trigger it builds up in the head.if your trigger gun is leaking internally then you will need to replace the gun thi ... Pressure Washers

My pressure washer starts fine, shoots water OK. After running for 5-10 minutes cleaning siding I shut off machine. I go to start it again within a minute or two and the thing feels like it's just about seized. If i wait until the motor is completely cool, it will pull start freely and start right up. I think something is wrong with the pump, not the engine.


Your pressure washer may not have an ez-start valve installed from the factory. Without the ezstart valve, you will need to hold the trigger on the wand open to release the pressure to easily start your engine. This link will show you wh ... Briggs & Stratton Pressure Washers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

Troy- Bilt pressure washer #020209 , 7.25 Briggs & Stratton, AR water pump #SJV 3G27-1. Boggs down an cuts off acts as if motor is getting tight with wand in use or not. After shut down its easily starts up an repeats itself. Removed pump motor runs fine.


... Briggs & Stratton Power Products 1539 Pressure Washer

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

I have a Karcher G2600 OR Pressure Washer, 2600 psi, 2.5 gpm. PN 1.194 506 0. gas engine works fine and water flows fine but pump is not adding pressure to stream. Checked and cleaned inlet water filter.


... Pressure Washers

Water pump I have a porter cable pressure washer model# 2425. I let my presure washer in the garage during the winter(no heat) and now i have a probem with the pump. I start the motor everything is find but when i put the water in the motor stop. Can you help me


... Pressure Washers

I have a Karcher K5.86m pressure washer and the electric motor wont start. I've done the obvious like fuse in the plug etc. It was working fine one day, then got it out again and everything seems fine except the pressure pump wont start when I press the on button.


... Karcher Pressure Washers

Troy Built pressure washer starts up fine and idles nice. Start spraying and everything is fine for about 30sec to 1min then the engine just shuts off. Seems like pressure is building up and choking the engine out. If I dont spray it will idle all day long. I have cleaned the unloader area, still shuts off. I have the pump off the machine, what should I do? Model number 020208 Troy Built. Rev # 01


... Pressure Washers

I have a troybilt 3300 psi pressure washer with a gx390 honda engine. Replaced carb with new one . washer now will start and runs fine under load but let off water and carb goes up and down and backf


... Pressure Washers

I have a Dewalt 3800 pressure washer fitted with a 67DX39G11 pump. Started unit up for the first this year, has pressure for 15 seconds then nothing. Water is flowing through okay, everything seems in order but no pressure. Unit is 2 years old but has only 15 hours of total running time. I think the pump has failed, is it normal for a pump to fail with only 15 hours on the clock?


... Dewalt 3800 PSI Pressure Washer

I have a Briggs Stratton Model# 020228 Gasoline Pressure washer with a Faip Brand Pump. The engine starts, the water supply goes thru the pump under its' own pressure. When I pull the trigger on the handle, there is not increase of force nor does the pump engage. I had this same problem several years ago and sent it to a dealer for service. His service tag indicated a stuck unloader. Where is the unloader located on this pump. The indentification on the pump is MTPV90736 191693 Order # 52


... Briggs & Stratton Pressure Washers

I have a Troy-Bilt GCV160 pressure washer. While I was pressure washing the water pressure just decreased. The unit will start and runs fine, but there is no pressure when sqeezing the trigger. I purged the water system with no positive results.


Hi and welcome to FixYa. I am Kelly\015\012\015\012First off let me say that the GCV160 is the engine model number and not the unit model number. \015\012\015\012It appears that your model number is 020415 (2600 PSI) as it is ... Pressure Washers

I have a campbell hausfeld 2450 pressure washer with water coming out of a brass hose nozzel right next to where you screw the high pressure to the pump as soon as you turn the water on from the house, start it up and high pressure comes out of it and the hose about half pressure, any ideas?


This is called the chemical injector which enables you to insert the hose for you to dispense the soap and or chemical by utilizing a soap nozzle .apparently inside this barb you will find a ball a spring and a o-ring,find the replacement parts or ki ... Campbell Hausfeld Pressure Washers

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started.


Ok I wasnt satisfied w/ the previous answer so I did some digging. I took off all the hose attachments and drained the line. I then checked for any clogging in ALL the screens. As usual the wand screen was clogged. this is an easy fix w/ a safety pin ... Pressure Washers

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

Bosch shu9925 At the start of the cycle, the washer is in pump mode. It remains that way. No water flows into the washer.. It just continues to pump. We checked the drain, some debris and checked to see how the pump was working, it is fine. Any suggestions?


Take bottom front panel off to expose the bottom tray. you will find there is water in it. mop water out and appliance will operate ok. turn off at mains first.\015\012\015\012if fault reoccurs, you have a leak which will have to be trace ... Bosch SHU9925UC Built-in Dishwasher

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244

I have a zr2700 pressure washer. As soon as it is started, water pumps through very forcefully. Pressing and releasing the triger on the wand does not control the water. Do I need a new wand or is there a problem with the pump


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1369 seconds