Having problems with your Briggs & Stratton Prosumer 20324 Gas Pressure Washer ?

The pull cord on gas pressure washer wont allow me to pull it as though it is tangled up, But when i removed the housing, it woorks just fine


Answers :

Sometimes the housing gets bent slightly. A lot of the housings have little taps or prongs that get slightly bent. I would take the housing off make sure it not bent or warp, to make sure there is nothing to block the free flow of then cord flowing. If it pulls fine with housing off, and hangs up when installed it slightly bent. Use small needle nose pliers and gently bend tabs away from area where cord is hanging up.
Repair Help & Product Troubleshooting for Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The pull cord on gas pressure washer wont allow me to pull it as though it is tangled up, But when i removed the housing, it woorks just fine


Sometimes the housing gets bent slightly. A lot of the housings have little taps or prongs that get slightly bent. I would take the housing off make sure it not bent or warp, to make sure there is nothing to block the free flow of then cord flowing. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

GE gsd2350r00cs fine filter removal. Once the spray arm is removed how do I remove the fine filter? does it pop out of the back? Don't wat to break it if I pull too hard and it's not supposed


... GE Dishwashers

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

KitchenAid 24 in KUDM0IT JWH0 auto test mode? Starts, fills, but doesn't wash or rinse, just hums, drains fine. There was **** in the screen with the chopper under the filter (clogged) a piece of glass got caught under there, I removed it, it worked fine until I removed the glass. I just did the auto test mode thing and it did some filling and then drained. Still not working though


... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

I purchased my KARCHER G2500VH last summer. I used it one time for about an hour. I tried to start it today, seems like its not getting gas. I checked the gasline to make sure gas was flowing. I removed the sparkplug, poured a little gas into the engine through the plug hole. Replaced the plug, pulled the rope and it started for about two seconds. I also poured fresh gas in tank. Cannot get to start.


Have tried to start our BlackMax 2700psi pressure washer, it is not getting gas to the carburetor, what to do? ... Pressure Washers

I pull the Ripcord and doen not start. The ripcord feels very hard when pulling. When I remove the chamber and inspect the cord mechanism, it seems to be working fine. thanks for the Solution


... Honda Pressure Washer PSI 3000

Engine will not turn-over. It is a Honda 11 HP, OHV on a Karcher Pressure Washer. It was running fine for about 45 minutes. All of a sudden it stopped. When I tried to start it again, the engine is bound up so that the pull rope will not pull out at all. It has plenty of gas. The crank case is full of oil, not over full.


Pull the spart plug out and see if you can pull it. Sometimes the carb will flood the engine to a point that they get hydrolic lock.If it does free up then I suggest cleaning the carburator before trying to start it again.If it does not free up the y ... Karcher 2500 PSI Pressure Washer

Hi I have a brand new Honda Power washer GC 160,2600 psi 2.3 GPM my husband taught me how to use it last night and I think I have followed all of steps: 1. hose free of kinks 2. connected to machine 3. purged pw handle of air and made sure water from house coming through 4. pulled out choke 5. turned red button to "ON" position 5. pulled T handle enging starter and it sounds like it will start but doesnt what am I doing wrong??? yes it does have gas in the fuel tank.


... Karcher 2500 PSI Pressure Washer

My pump is gone on my pressure washer. The honda engine is GC 160. The pump is a model VRX2527G. How do I pull the pump off the engine to replace it. I removed the four bolts from the pump housing, but the pump is still tight to the shaft. Please explain the removal process.


Hello,Your pump sits on a keyed shaft, versus a taper fit. This is good, since tapered shafts will require a puller to remove the pump.Since the pump is already bad, you have a few options available to you. 1) W ... Honda Pressure Washers

I have a Troybuilt pressure washer which has a Honda GC160 engine. The engine starts easily but quits after about a minute. One pull and it re-starts, then quits in a minute....... This goes on for as long as I want to keep re-starting it. Anyone know what it might be? I pulled the carb off and blew out all of the various ports I could find. I did not remove the carb adjustment screws as I have not had any luck getting them back in place during previous problems with other gas engines.


... Karcher 2500 PSI Pressure Washer

I have a Fisher and Paykel dishdrawer model ds603. Not sure eactly what happened but my son says that the cycle stopped last evening (and only tells me this morning!). Dishes though appeared to be clean and there was a small amount of water at the bottom. I tried opeing the washer and it was hard to open as though the drawer was stuck on something. I removed the drawer and checked the rollers and they are fine. I realised then that the drawer is getting stuck on the inside lid that provides the


The best thing to do is to remove the rack,drawer completly,and close it up,see if it will come on,and run all threw the cycle.If it does,then put the rack,drawer on the track.The rollers could be,well,not snapped all the way on.It will be in that ar ... Fisher Dishwashers

Leaking Dishwasher seems to be leaking. Otherwise it's performing fine. I have laminate floors, and there are water seeping out along the seams of the flooring area near the dishwasher. The dishwasher is captured by the floor (dishwasher was installed first then floor was put in at 1/2" higher level), so we can't pull it out to check where the leak is coming from. Can dishwasher be repaired from the inside w/out removing it from where it is? Only way to pull it out seem to be cutting a part of


This is a huge problem for you. when you have a leak coming from the bottom of the dishwasher the machine will have to come out. but first check the door gasket to make sure the leak is not coming from there. ... Jenn-Air 24 in. JDB4950 Built-in Dishwasher

I have an Excell VR2500 pressure washer with B & S 6.5 HP engine. It was running fine, but then stalled out and now will not start. Has clean gas and full oil. I pulled the spark plug it is producing a sufficient spark when starter cord is pulled. Any ideas what might be causing the problem? Please help.


The key things to check are the spark plug, the air filter, the fuel. If those are all new and in good shape then you probably have gum in the carburator. Get a can of starter fluid and a helper. One person squirt the starter fluid into the air in ... Briggs & Stratton Pressure Washers

Hard starting 6hp Briggs and Stratton power washer engine. I poured a teaspoon of gas into the cylinder; reinserted the spark plug and with one pull in ran fine. This is a choke start engine and it may take 12 to 15 pulls to start on a cold engine. The unit is clean. The air cleaner is new. The spark plug is new. The unit is 2 years old with very little use.


Hello. I have this same machine. Go to the auto parts store and get an aerosol can of starter fluid. Have a helper squirt some into the air intake while you start it. Then continue to squirt a little starter fluid as it runs for the first two mi ... Campbell Hausfeld Pressure Washers

Engine does not start. I ran it about two weeks ago and it worked fine. I took the spark plug out and it was dry. I made sure there was gas in it. I tried some starting fluid by spraying into air intake and it start running for a short time until the starting fluid ran out. I removed the carb bowl and there was gas in it. However the inside of the bowl and the float had brown deposits and looks like rust. So I think the main jet has been clogged up with a particle. How do I clear it? Where do I


Try cleaning the carb with gumout spray and a little compressed air, be careful to reassemble the float and needle valve exactly as you found it. ... Northstar Pressure Washer 3000 PSI

Hi, I have a 10yr old Neff s5543 built-in dishwasher, it is has been working fine but recently has stopped fully draining. I have removed it from the housing and checked all pipe work is unblocked and not kinked, have also blown back down drain tube to free any blockages from drain pipe, have also removed pump cover and checked around impellor for any foreign bodies etc. Everything seems clean and free. I ran a complete heavy cycle (empty dishwasher) and allowed drain pipe to drain into a


Hello there and thank you for choosing fixyaOk there are acouple of things that can be checked on this along with what you have already checkedDrain solenoid\015\012 \015\012 \015\012 \015\ ... Neff 24 in. S5543X2 Built-in Dishwasher

Unable to start gas engine on a NorthStar pressure washer


Disassemble and clean the carb. If it ran briefly with the starer fluid then gasoline is not coming through the carb. ... Northstar Pressure Washers

Power washer Briggs & stratton model 2200 from sears. Just pulled out of my shed. Runs fine but water pressure is really low. I cleaned everything that may be blocked. Water pressure from house is ok.. I'm lost Help thank you.


... Pressure Washers

I have a 2300 psi gas pressure washer, campbell hausfeld, runs fine but water comes out the nozzle like a hose , no high pressure. inlet filter is clean and when you pull the trigger on the nozzle water comes out like a hose but no pressure


If you no longer have High Pressure coming out while machine is running, it's a pump issue. ... Campbell Hausfeld PW2575 Pressure Washer

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

My dishwasher so my dishwasher seemed to have quitworking during a cycle. like breaker triped or something. i checked the breaker and thats fine. it seams like its hard wired in though. Would that be right? and is there a fuse or something that could/would blow during a wash? I dont know what model it is or anything it was in the house when i got it. The dishwasher is built in and it seems decently old its a kenmore ultra wash and it has like 10 buttons for the differend cycles on the left and a


Sounds like the fuse on the control blew. you can replace the fuse for\015\012around $20 or you can cut and splice the wires for free. If that doesnt\015\012work then you may have a loose conection in your junction box under the\015\012dishwasher. ... Kenmore 24 in. 15932 Built-in Dishwasher

Bosch SHU4302 WITH REPAIRED PC BOARD has been working fine for several years now seems stuck in rinse/drain mode and is not quite pumping cabinet dry. I have removed the screens and located the small impeller at bottom below cover. The impeller rotates as though it has multiple spring loaded stop positions. When I turn on the unit and open the door water is trickling from the sprayer arms at low pressure. It seems stuck in rinse mode and will not advance cycles or reset when shut off.


... Bosch Dishwashers

Hi I've inherited a Zanussi DA6142 Dishwasher from a recent house move. It was treated quite poorly by students who I suspect ran it without the filters in place. I've used a dishwasher cleaner and was able to pull out the lower spray arm and rinse out all the crud that was blocking it (small stones, food, plastic, pieces of glass, paper, etc) but I cannot for the life of me work out how to get the upper spray arm out. The PDF manual I've downloaded for this model says DO NOT remove upper spra


... Zanussi Dishwashers

With pump removed engines runs fine. When new pump is installed it is very hard to pull with water flowing but will not start. Engine was just tuned up late year.


Chances are that your new pump is generating good pressure. Because of this, the engine is trying to turn over against the pressurized system. Try pulling the handle on your wand when pull starting the engine to see if this eliminates your problem. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a kohler command pro 8.5 on a porter cable pressure washer. Yesterday it started just fine. Today I pulled the start rope and there was no resistance and the engine did not turn over. The pull rope rewound just fine and I tried again with the same result. After several tries it caught just a little near the end of the pull and the engine started. What is the cause of this problem?


... Porter Cable Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0631 seconds