Having problems with your Briggs & Stratton Prosumer 20324 Gas Pressure Washer ?

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


Answers :

If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you dont see any spark between wire and spark plug, tehre its not spark ,it will never start.you will have to remove the start recoil on the botton is like a damper whitch will have to be remove also ,on botton of it its like a coil whitch with the rotation of the damper when you pull the starter rope provoke the spark and send it to spark plug along with the gas combution get the engine started.that coil some time goes bad and have to be change.if you have electric starter. check the starter also.good luck
Repair Help & Product Troubleshooting for Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Home Depot has a lawn mower with the Honda GCV160 Electric start version engine. They also have a pressure washer with the Honda GCV160 engine. I have a disability that makes it difficult to pull the starter rope. I would like to get the electric start on the pressure washer. My local Honda bike shop service center said they use different blocks. Can I get a pressure washer pump mounted to the Honda GCV160 Electric start version engine? If necessary, are there adapter plates that can be purchase


... Karcher 2500 PSI Pressure Washer

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.


... Karcher 2500 PSI Pressure Washer

I have a dewalt dp3100 pressure washer, i was using it for about an hour then it ran out of gas. After adding some gas it refuse to stop, it start for a few seconds then it would stop. its full of oil (but the oil is a little dirty) and the gas is half full. what could be the problem?


... Dewalt DPD3100 Gas Pressure Washer

Hi ..I have an Excell gas pressure washer model no. Exwgv2121-3 with Faip 2100 psi 2 gpm vertical shaft pump..the problem is that there is water leaking from every weep hole at the bottom of the pump when running. Oddly enough,the pump still puts out significant pressure but less than it should due to the leaking water. What is the most likely cause of this?..is it the high pressure water seal(s)? If so,how do I repair it?


... Pressure Washers

I have a excell 2500 psi max honda 5.5 ho vr2522 2.2 gpm presser washer and has been stored for about a year, still looks brand new and has only been used twice before, it has oil and was stored with no gas in the tank, i put fresh gas in the tank and blead the fuel bowl until fuel ran out like it should, the washer wont start, ive checked the turn on switch as well and the fuel cut off knob, i spayed gas in the carb and it fired up but stopped running as fast as it began to run, its not getting


... Honda Black Max 2600 PSI Pressure Washer

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

Hi i would like to thank the experts who gave me lot of hepl regarding my HOBART AMX-70 dishwaser. Final question the pressure switches b3 and b4 do they work with water or air pressure [meaning how do they get activated. Once again thanks for all the help.


Hi,\015\012 \015\012Thanks for writing to Fixya.com.\015\012 \015\012The inlet valve is energized directly by pressure switches B4 (31-32) and B3 (21-22). These contact ... Dishwashers

I would like to get a user manual for LG dishdrawer model DD603, Australian model. Failling that what I really need to know at present is how to use the lock button - just pressing it doesn't seem to work. I need to be able to stop my toddler starting and stopping the dishwasher at her own whim! The front display has three buttons, 'power', LED display then 'Start/pause', & 'lock'. Thanks Shelley


Opps wrong make & model. Searched for fisher & Paykel and found what I needed! No longer need a solution. ... LG Dishwashers

I have gcv 160 5.5 hp power washer my problem is that the high pressure pump is not working properly when the engine is running the output pressure is very low so i would like to know could be the possible cause of that problem


look for a black plastic cover with a silver snap on top; pry off the silver snap and lift off the plastic cover; next remove the two screws on the top plate then pull out the piston inside - if unable to lift out, start unit and watch it pop ... Karcher 2500 PSI Pressure Washer

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

Hello , we have a blanco BFDWC65 dishwasher supplied to us by our builder , The dishwaser fills with water ok then once in cycle it starts (with all operating lights ) then stops , it continues to start then stop for the rest of the cycle , Quiet some time later it finished and then drained the water ok , now it struggles to get to the end of the cycle. have checked all filters , water pressure and for clogged hoses , everything is ok in that department. Any help would be apprieciated


I would suspect the control board in this type of behaviour. As the machine is new I advise no interference, but to open a claim under warranty. You would have all the warranty papers for this unit, or should have received them from your builder. The ... Dishwashers

I have a Whirlpool Gold Quiet Partner III that is 8 years old and recently stopped cleaning top rack dishes. I remember finding a mylar like piece in the bottom of the tub and threw it away thinking it came off of something we washed (I know, bad thinking.) The mylar piece measured roughly 3-4inx2in and was folded in half. Anyways....the upper arm does not spin and the detergent doesnt get fully dispensed so dishes dont get fully cleaned. I am guessing not enough water pressure to upper arm. Wou


I'm having a similar issue. Are you sure the arm isn't moving at all?\015\012\015\012Generally what I'm finding is either you have a clog or the pump motor is bad.\015\012Hear is the service manual.\015\012 ... Dishwashers

Stopped working no power light come on like it's dead.The power supply is fine to the plug and the fuse is ok it just stopped why? is there a reset button anywhere?what would cause this? no hint of a problem before


Check where the pig tail the plug going into the wall follow the plug wire to the connection at the dishwasher. You will need to remove the bottom panel of the dishwasher at the floor. This access panel allows you to see the underneath of the dishwas ... Dishwashers

It looks like gas getting into the crankcase oil,


Here`s the go ,good possibility that you didn`t turn the gas tap off at the last time you used it.If the needle isn`t seating properly the gas wii over flowinto the carburetterif the inlet valve is open ,fuel can ,if the macine is on uneven ground ... Karcher 2500 PSI Pressure Washer

My motor will not start?? It gets spark, I see the piston fire, Is it out of time. seems like there is too much gas. How would I check for timing. Or other problem. Mike [email protected] thanks for the help.


Has it been sitting for a long time? 9 times out of 10 the carburetor is dirty and just needs to be cleaned. you could soak it in some carb cleaner sold by auto parts stores or go so far as to buy a rebuild kit for it and replace gaskets and such. ... Honda Pressure Washer PSI 3000

I have a NorthStar pressure washer M157471A.It has started leaking from the pump. I have stripped it down and would like the valve kit A and the piston seal kit B item 5026 0257 and 5026 0256 . Were will I get these from?


NorthStar is a Northern Tool housebrand. You can contact them using the information below, and order the parts that you need.Contact a Northern Tool Product Expert:Call 24/7: 1-800-221-0516Alternatively, you can also or ... Northstar Pressure Washers

My dishwasher top washer is not spinning....What causes it to turn (water pressure)? and if so does it recirculate the water...my inlet could be stopped up...dishes on top rack are not getting cleaned


Water is just circulated by a pump motor, Check to make sure it is getting enough water (just around the element) ... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

What would cause a pressure washer to cut off after you pull the handle to get the water started


We used power washers for yearsWhen you pull the trigger, the engine is supposed to accelerate because the back-pressure on the pump is released.The back-pressure is why you're supposed to keep the gun trigger open when starti ... Pressure Washers

I have an Electrolux dishwasher model DX102SJ*02. One of the roller assemblies that hold the top tray on the rails has broken causing the tray to droop. I would like to know what part number I need and where I can get it. I live in Darwin NT, Australia.


Sir/mam\015\012\015\012\015\012 try www.partnship.com.au ... Dishwashers

My Husky HU 80709 gas pressure washer starts (most of the time) but if I shut it off to answer a phone call, etc.,I cannot get it started again. It's like it has a vapor lock or something. Any ideas what is wrong, suggestions to fix it, will be very appreciated. Thanks! [email protected]


I have the same power washer. \015\012\015\012When you go to restart it you need to hold the sprayer nozzle so the their is no pressure in the hose. It is even better if you take the tip off the spray nozzle and then while holding the spray no ... Honda Pressure Washer PSI 3000

Dishwasher 66513752K601 keeps blowing the thermal fuse. (Bi-Metal W10258275). I have replace the Thermal fuse several times. After i replace the fuse for some reason after a few months or less it will blow it out again. I have also replace the front panel assembly after it stopped working correctly. I would like to know how to test the dishwasher to find out the root cause of the fuse issue. I don't want to be replacing the fuse every time and don't have the $$ to buy a new dishwasher. Everythin


... Dishwashers

We have a Kenmore Ultra Wash Dishwasher, several years old. The lock light went on yesterday and we could not put it on wash or anything. We hit cancel, unplugged the machine, left the door open so it would stop the cycle...nothing worked. How do you get the lock off when it goes on like that? I just went into the kitchen, shut the door and the lock was off, strange.


There is a key (usually the dry key) that needs to be held for 4 seconds to turn the child lock on or off. If it comes on again try holding this key for 4 seconds.If it was pressed and held by mistake this could cause the lock to activate ... Kenmore Dishwashers

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

KitchenAid dishwasher: KUDS01FL - I have had to replace the fuse every year and now I can't even get through on cycle with the fuse going. It is now dead again! It almost makes it through the full cycle and then stops (fuse blows)- no power - and there is some water left in the bottom which I have to physically remove. I spent a fortune on repairs every year since I bought it and would like to try to avoid another charge. I appreciate any help that you can offer. Thank you, Carol


I would check the pump. It may be slightly jammed or have debris which is causing it not to fully move or cause it to move very hard popping the breaker. Also with a jammed or broken pump, that can also cause water to be left in the bottom of the mac ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1042 seconds