Having problems with your Cam Spray 25006HT 2500 PSI Cold Water Gas Trailer Mounted Pressure Washer with 6.5 HP Honda Engine ?

Will not release pressure and dies

\015 Having trouble keeping the pressure washer started. you have to hold the handle in on the nozzle in order to keep the pressure washer running. when you release the handle the pressure washer dies\015

Answers :

Your unloader valve is not functioning. Take it apart and make sure it all the parts are able to move freely under the spring. You may need a new o-ring or two if you see damaged ones.
Repair Help & Product Troubleshooting for Cam Spray 25006HT 2500 PSI Cold Water Gas Trailer Mounted Pressure Washer with 6.5 HP Honda Engine

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Will not release pressure and dies


Your unloader valve is not functioning. Take it apart and make sure it all the parts are able to move freely under the spring. You may need a new o-ring or two if you see damaged ones. ... Cam Spray 25006HT 2500 PSI Cold Water Gas Trailer Mounted Pressure Washer with 6.5 HP Honda Engine

I have a troy built power washer powered by honda. It runs for 10 - 15 minutes and then dies. I have replacced the ignition coil, spark plug, rebuilt the carburetor, checked fuel flow and placed the unloader valve and it still dies. Once it dies and the pressure is released it repeats the problem. Any suggestions?


... Honda Pressure Washer PSI 3000

Pressure washer dies when trigger is released.


... Craftsman 2550 MAX PSI Briggs & Stratton Powered

Engine dies when pressure washer trigger is released-kickback


... Pressure Washers

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

I have a Mi T M job pro 3500psi pressure washer that may have a clog in the nozzle, how do I release the pressure in the line? All the pressure fittings are stuck (probably from the pressure in the line), even the one at the nozzle. Is there a pressure release somewhere on the machine?


... Mi T M WP-2700-4MHB Pressure Washer

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

I have a Simoniz S2800, it will only start with the trigger depressed to release the pressure and when it starts the engine seems laboured and there doesn't seem to be the ame pressure as it used to have, also if it isn't used after a min or so it will release water pressure from the bottom, do I need a seal kit or a pump kit to correct this problem.


Where is the unloader valve on these machines? ... Pressure Washers

My 3.99 Karcher pressure cleaner seems to keep going on,off,on,off when i release the trigger.It used to keep going momentarly when the trigger was released until the pressure built up,then cut off until the trigger was pressed .Now it goes on ,off,on,off and has decreased pressure.


Hi! robcarrollDid you purge the air from the pump before starting the motor.InMrFixIt ... Karcher 2500 PSI Pressure Washer

Karcher 620M.To obtain high pressure I have to Move pressure control on nozzle several times until pressure kicks on. As soon as I release trigger and then pull it again, I have same problem -- giggl


... Pressure Washers

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Engine dies when wand trigger is released


Re-kit the unloader. ... Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer

I just purchased a Simpson Megashot V3000 Pressure Washer and noticed the engine would stop running every time I released the wand trigger. Also, water was constantly spraying out of a valve underneath the unit - I assume it's some type of pressure release valve but there is no mention of it in the owners manual. I am thinking about returning it to Costco for a refund.


... Simpson Pressure Washers

Deville Excel Model # EXHA2425 Pressure washer I have a deville excel Model # EXHA2425 pressure washer. I went to the deville website (devap.com) which forwarded me to the dewalt site w/ exploded diagram below. I am having problems with intermittent pressure production. If I squeeze the trigger sometimes it will have pressure, somethings it will not. If I repeatedly squeeze, then release the trigger sooner or later I will get pressure. Someone on hear had told me it was a "bypass valve sticki


You\015\012need toput antifreeze in the out/outlet or/oil then start it up you are driing out the seals allways put away with repeating this step ... Karcher 2500 PSI Pressure Washer

My Karcher K3.48M pressure washer remains in the low pressure mode even when I return the pressure nozzle to the high pressure position. How can this be corrected. The pump seems to build up the pressure because when I release the handle the pump motor stops. This is a fairly new pump which was purchased in the latter part of last year(2010). Could this have been caused by the detergent I have been using which is an automotive shampoo? Please help I love this washer and for the times that I u


... Karcher PSI Electric Pressure Washer

Pressure washer When I crank the pressure washer it will provide great pressure. When I release trigger and press it again it will not pressure up. what's wrong?


... Karcher 2500 PSI Pressure Washer

Kranzle 160t pressure washer works but full pressure drops off I then release the pressure trigger for a while and it will work at full pressure again for half a minute.


... Pressure Washers

Low pressure While I initially get high pressure, when I resume washing after having released the trigger, water pressure is low. By removing the nozzel tip and reinstalling, high water pressure is resored. What is happening?


If this keeps happening repeatedly it sounds like you need a new seal kit put in it can be done easily enough by you or you can get a shop to do it , if you live in a cold winter climate be sure to winterize the washer every year or keep it somew ... Karcher 2500 PSI Pressure Washer

North star petrol pressure washer. working fine, then no high pressure, checked water feed, water filter , pressure relief valve and gun nosall well work sometimes and keep working, when you release the trigger and try in again the pressure gone again. please help, many thanks, richard


Sounds like the regulator is sticking or is airbound. loosen the water connection and then tighten it back. Could also be that the trigger gun is faulty or needs adjustment. Hope this helped ... Karcher 2500 PSI Pressure Washer

My Karcher 411A seems to have lost pressure. Behaviour is this, when you press the water release on the spray gun you get 100% pressure for like 10 seconds and then it seems to dwindle down to 30-40% of its total pressure. When the pressure cuts down I can hear more noise coming from the gun sprayer aswell. So not sure if the problem is in the gun or the main pump unit ?


Sounds more like a clog on the intake side. Check the filter and the hose on that side. ... Pressure Washers

I have the Coleman powermate 2400 PSI pressure washer and on initial start it sprays and has great pressure. But once I release the spray handle it will not spray again, not even one drop of water. I have verified water pressure, bought 3/4 hose, and also changed the spray handle with no help. Pressure washer was bought new at Lowes, but did not use for first three years of ownership, should have tested it. Thanks for any help on this. Ted Miller


Sounds like the valve in the handle is sticking closed. May have a broken spring, or maybe a part is stuck..\015\012I say take it apart, and the answer will present itself.. Play with it with nozzle out too... Maybe something is stuck after st ... Coleman Pressure Washers

Fluctuating pressure I have a brand new Northstar 4000 psi, which I started using today. I start the PW and the pressure is great, then the pressure drops. If I release the trigger the problem repeatsand if I hold the trigger the pressure remains low. Very frustrating when you are trying to work.


... Northstar Professional Series Pressure Washer 4000 PSI

I have 2400psi washer gas will run w/hi pressure, when i release trigger and then pull trigger for hi pressure it will take minutes to get hi pressure, longer i run longer for pressure to come back.


Hi and welcome to FixYa. I am Kelly. \015\012\015\012First off check to see if there is an inlet screen at the house water hose connection point. Remove it and clean it then reinstall. If the screen was clean.......\015\012The u ... Honda Karcher G2400HH-R Pressure Washer

Deville Excel Model # EXHA2425 Pressure washer. Is "unloader" the same as "bypass valve"? I have a deville excel Model # EXHA2425 pressure washer with a 5.0 Honda enginr. I went to the deville website (devap.com) which forwarded me to the dewalt site w/ exploded diagram below. I am having problems with intermittent pressure production. If I squeeze the trigger sometimes it will have pressure, somethings it will not. If I repeatedly squeeze, then release the trigger sooner or later I will get p


... Pressure Washers

Need pressure release valve knob for cooks essential electric pressure cooker


... Cook's Essentials 5-Quart Multi-Function Pressure Cooker Refurbished K34186
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0638 seconds