Having problems with your Campbell Hausfeld Elec pressurewasher 1600psi ?

Elect. motor dosnt turn off when i release triger


Answers :

High pressure cut out switch is faulty or not enough pressure to activate switch . more likely the first.
\012it migh be a simple micro switch . inside a platic housing on the end of the pump inside cover.
Repair Help & Product Troubleshooting for Campbell Hausfeld Elec pressurewasher 1600psi

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Elect. motor dosnt turn off when i release triger


High pressure cut out switch is faulty or not enough pressure to activate switch . more likely the first.\012it migh be a simple micro switch . inside a platic housing on the end of the pump inside cover. ... Campbell Hausfeld Elec pressurewasher 1600psi

Pressure washer runs fine until I turn hose on, runs for a minute than motor stops, I release garden hose connecton and motor will run fine....


... Karcher 2500 PSI Pressure Washer

Dear Sir, I have a Karcher water pressure mod.299. In the past when I did release the trigger,turning off the water jet, the motor would automatically stop now it stays on. Why? Please help if you can. Regards Oscar


... Karcher 2500 PSI Pressure Washer

I have a SMEG DWF614 SS dishwasher. I continue to get an E8 error message. The diverter valve motor turns freely & the motor turns freely when they are seperated. However, when they are assembled, the motor turns the valve & continues to try turning the valve when the valve is on its stop position. Is the motor & valve faulty or is it the control. If you can answer, what part number would I require. Regards Leighton Davies


... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

Whirlpool dishwasher part #3385181. Machine had gone thru wash cycle and was starting to dry. Smelled electrical burning smell, opened washer door and washer was filled with smoke. Turned everything off, cleared smoke, and the washer water dispenser is very hard to turn. Washer has symptoms of burnt up motor that turns water dispenser. Machine is 12 years old. With cost of replacement motor and possible part (pump?) that might have clogged and caused motor freeze up, is it worth fixing or junk


... Dishwashers

Maytag DWU6402AAB dishwasher hums but motor does not run. I've taken the inside apart down to the disk-shaped impeller. It turns freely so the pump and motor are not stuck. When control knob is turned motor hums at the places where it normally should run. The water valve & heating coil seem to be operationg normally. i assume the next step is to test the motor &/or motor relay. Is this correct and how do I do that?


... Dishwashers

I have a Whirlpool dishwasher (model DU890SWKQO). I turned it on and for a few minutes only the motor was running, no water. I opened the dishwasher to stop it and turn it off, then on again. When I opened it, the was an odor (burning or heat smell) and it was foggy (steam or smoke, not sure which) inside. I am assuming I did not turn the dial correctly so it only 'clicked' on the motor. Concerned now that the dishwasher is broken or concerned that it's not safe to use. Was the steam/smoke


... Dishwashers

Hi i have a karcher hds 745 and when i turn the switch on the motor runs all the time and dose not stop


... Karcher Pressure Washers

Stalls when triger released


The problem may be the oil. if the oil is fine then try crimping your hose to let less water pressure through. if that still does not work lowes or home depot will fix the problem cheap. thank you for using fixya ... Pressure Washers

I have a kitchenaid kuds01flss5 and i replaced the grinde assembly, but for some reason it does not reach the motor that is supose to turn it. i found this out due to it continuing to get clogged. i am pretty sure i have it installed correctly but it is clear that when i turn the blade it is not connected to the motor. any ideas?


... KitchenAid Dishwashers

Karcher K3.92 M 1750 PSI poweer Washer motor won't start. Followed Reset/Test/Reset sequence with cord plugged directly into outlet. Light on cord near Reset comes on when Reset pressed down but goes off when Reset released (Normal?) Switch ON and trigger pressed releases water stream but no motor action.


They are sensitive to large extention cords. My father in laws pops reset when a small cord is used. If internally shorted- motor will continually pop the reset even plugged direct to outlet. Check voltage at outlet. ... Karcher 2500 PSI Pressure Washer

Ld-1416T I have an LG LD-1416T dishwasher and the lower spray arm does not turn. The top arm turns and the top rack is washed well. I pulled everyting out and cleaned all the filters (which weren't that dirty) but still no luck. I could only get so much stuff out to clean before it looked like to go any further, I would need to gain access through the bottom. Are there more filters in the motor area which might need cleaning? I read that it could be the vario motor. Can I test this? and if s


If you have one spray bar working then there is enough pressure. There is only one pump. So you should check the spray bar to see if it is plugged. Also check the seals to see if they are bad. ... LG Dishwashers

Hi- I have a Simoniz S1600 pressure washer and usually when I first turn it on, the motor turns on to build up pressure. Now the motor won't kick in no matter what I do. Water still comes out of the gun as a small stream but there is no pressure. There are no reset buttons on the exterior of the machine. Thanks!


... Pressure Washers

Upper & bottom arms are not turning even though the motor seems OK, pump for draining seems OK too. rcently I changed the pump kit plus some gasket and seals. My Maytag is about 14 yold and was very good for me untill I changed the parts. Could it be a weak motor pump. The water splashes very much in the machine but no arm turning!? Help me thank you Ben


Hi Ben, had the motor impellor shattered in the old pump ie-chunks broken off ? if so there is every possibility that these pieces have lodged in the wash delivery pipework at an elbow or indeed at the arm boss itself -i would try to check as much of ... Dishwashers

When i turn my Viking dishwasher on the motor starts to run but no water comes out. It was humming along for several hours before i realized that nothing was really happening. I turned it of and then tried again but the same thing happened. It sound like a motor and/or pump working but no water enters the chamber. Thanks, Jonathan


It sounds like the Water Supply Solenoid is bad. I would change that and let all of us know what happens. ... Dishwashers

Brand new Stanley 1800 power washer - just bought it yesterday. Powered it on - realized I hadn't turned the water on - so turned it off - turned the water on and turned the Stanley back on - it ran for a second and powered off. Now it won't turn on again. Did I burn out the motor?


... Stanley Pressure Washers

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti


I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

Water stays in dishwasher goes through cycle but motor not going if turn propelers at back of motor pump kicks in for few seconds.is it pump motor ,is there brushes in these motors


Yes there are brushes in dishwasher motors it sounds like they are either worn out or stuck try tapping motor with the wooden end of a hammer at the rear of motor as brushes clog up as they wear hope this helps ... Tricity Bendix 24 in. BDW53 Free-standing Dishwasher

Both drawers of dishwasher have the motor running but nothing happens. I turn them off and they turn back on.


... KitchenAid 23 in. KUDD01DPPA Stainless Steel Dishwasher

GSD2200G00WW. When starting washer, part of the time the machine will not start, other times if machine has been running for a while and you open the door and try to restart the machine it will not restart. You can hear the motor humming as if it wants to go but it will only restart if you turn the motor shaft even just a little. I am wondering if the electric motor is dying??


... GE GSD2200G Built-in Dishwasher

My karcher k2.180 is surging when water and motor turned on. I've disconnected the hose and water is flowing and the motor running smoothly. However when I've reconnected again the motor is


... Karcher K2.26 Electric Power Washer

The motor is making a loud humming noise when turning on, water comes out, then stops, and the fan shuts off, then motor keeps making the humming souond? Does the motor need to be replaced?


... GE Dishwasher Mechanism Assembly - WD26X10045

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

I have a kenmore 15951793 it refuses to drain. I've metered the drain line into the motor and it is there but it will attempt to run but seems to trip a thermal breaker. the motor doesn't turn at all but the motor shaft is free, so I'm assuming bad coil. Any thoughts??


... Kenmore 24 in. 15932 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0876 seconds